Mazda CX-9 Grand Touring. Manual — part 461
TRIM REMOVAL/INSTALLATION .)
4. Remove the bass-box. (BSM control module (LH) only) (Vehicles with Bose®) (See BASS-BOX
REMOVAL/INSTALLATION .)
5. Remove the BSM control module with the connector connected.
6. Measure the BSM control module terminal voltage using the short wiring harness connector in the
position shown in the figure.
Fig. 17: Identifying Trunk End Trim & BSM Control Module Short Wiring Harness Connector
Courtesy of MAZDA MOTORS CORP.
TERMINAL VOLTAGE TABLE (REFERENCE)
NOTE:
The BSM control module connector cannot be connected to a tester
due to its water-resistance processing, therefore the short wiring
harness connector is used for measuring the terminal voltage.
If the terminal voltage is not as indicated in the table, inspect the
short wiring harness connector for continuity. (See CONTINUITY
INSPECTION OF SHORT WIRING HARNESS CONNECTOR.) If the
short wiring harness connector is normal, inspect the parts under
"Inspection items".
If the system does not work properly even though the parts or
related wiring harnesses do not have any malfunction, replace
the BSM control module.
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:42:27 AM
Page 31
© 2005 Mitchell Repair Information Company, LLC.
Fig. 18: Identifying BSM Control Module Short Wiring Harness Connector Terminals
Courtesy of MAZDA MOTORS CORP.
VOLTAGE SPECIFICATION
Terminal
Signal
Connected
to
Measurement condition
Voltage (V)/
Continuity
Inspection item (s)
A
BCM GND
Body ground Under any condition
1.0 or less
Related
wiring
harnesses
B
BSM
indicator
light signal
BSM
indicator
light
Ignition switch is in ON
position and BSM indicator
light is illuminated
B+
BSM
indicator
light
Related
wiring
harnesses
BSM indicator light is not
illuminated
1.0 or less
C
-
-
-
-
-
D
(1)
BSM OFF
switch signal
BSM OFF
switch
Ignition
switch at ON
BSM OFF
switch is pressed
1.0 or less
BSM OFF
switch
Related
wiring
harnesses
BSM OFF
switch is not
pressed
B+
D
(2)
-
-
-
-
-
E
-
-
-
-
-
F
CAN_L
-
Because this terminal is for communication,
good/no good judgment by terminal voltage is
not possible.
Related
wiring
harnesses
G
Power
supply
fuse
Ignition switch at ON
B+
fuse
Related
wiring
harnesses
Ignition switch off
1.0 or less
H
CAN_H
-
Because this terminal is for communication,
good/no good judgment by terminal voltage is
not possible.
Related
wiring
harnesses
(1)
BSM control module (RH) only
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:42:27 AM
Page 32
© 2005 Mitchell Repair Information Company, LLC.
CONTINUITY INSPECTION OF SHORT WIRING HARNESS CONNECTOR
1. Verify that the continuity between the short wiring harness connector terminals is as indicated in the
table.
If the continuity is not as indicated in the table, replace the short wiring harness connector.
(2)
BSM control module (LH) only
NOTE:
Terminal voltage of both the left and right BSM control modules is
equivalent
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:42:27 AM
Page 33
© 2005 Mitchell Repair Information Company, LLC.
Fig. 19: BSM Control Module Short Connector Terminals Continuity Chart
Courtesy of MAZDA MOTORS CORP.
BLIND SPOT MONITORING (BSM) OFF SWITCH REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the dashboard under cover (LH). (See DASHBOARD UNDER COVER
REMOVAL/INSTALLATION .)
3. Remove the hood release lever. (See HOOD LATCH AND RELEASE LEVER
2008 Mazda CX-9 Grand Touring
2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:42:27 AM
Page 34
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст