Mazda CX-9 Grand Touring. Manual — part 307
availability.
Is any related Service Bulletins
available?
step.
No
Go to the next step.
3
INSPECT THROTTLE BODY
CONNECTOR FOR POOR
CONNECTION
Turn the ignition switch to the ON
position (Engine off).
Disconnect the throttle body
connector.
Inspect for poor connection (such
as damaged/pulled-out pins,
corrosion).
Are there any malfunction?
Yes Repair or replace suspected part, then go to Step 9.
No
Go to the next step.
4
INSPECT THE THROTTLE
ACTUATOR
Inspect the throttle actuator. (See
THROTTLE BODY
INSPECTION [MZI-3.7] .)
Is there malfunction?
Yes
Replace the throttle body, then go to Step 9. (See
INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [MZI-3.7] .)
No
Go to the next step.
5
INSPECT PCM CONNECTOR FOR
POOR CONNECTION
Turn the ignition switch off.
Disconnect the PCM connector.
Inspect for poor connection (such
as damaged/pulled-out pins,
corrosion).
Is there any malfunction?
Yes Repair or replace suspected part, then go to Step 9.
No
Go to the next step.
6
INSPECT THROTTLE ACTUATOR
CONTROL CIRCUIT FOR OPEN
Disconnect the PCM connector.
Inspect for continuity between the
following terminals:
Throttle body terminal A and
PCM terminal 2BO
Throttle body terminal B and
PCM terminal 2BR
Are there continuity?
Yes Go to the next step.
No Repair or replace suspected part, then go to Step 9.
INSPECT TP SENSOR SIGNAL
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 361
© 2005 Mitchell Repair Information Company, LLC.
7
CIRCUITS FOR SHORT EACH
OTHER
Turn the ignition switch off.
Disconnect the throttle body and
PCM connector.
Measure resistance between throttle
body terminal A and B.
Is the resistance more than 10
kilohms?
Yes Go to the next step.
No Repair or replace suspected part, then go to Step 9.
8
INSPECT HROTTLE ACTUATOR
CONTROL CIRCUIT FOR SHORT
TO POWER SUPPLY
Turn the ignition switch to the ON
position (Engine off).
Measure the voltage between the
following terminals:
Throttle body terminal A and
body ground.
Throttle body terminal B and
body ground.
Are there voltage B+?
Yes
Repair or replace suspected part, then go to the next
step.
No
Go to the next step.
9
VERIFY TROUBLESHOOTING OF
DTC P2100 HAS BEEN COMPLETED
Verify that all disconnected
connectors reconnected.
Clear the DTC from the PCM
memory using the M-MDS.
Perform the KOEO or KOER self-
test using the M-MDS.
(See KOEO/KOER SELF TEST
[MZI-3.7].)
Is the PENDING CODE for the
DTC present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
10
VERIFY AFTER REPAIR
PROCEDURE
Perform "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 362
© 2005 Mitchell Repair Information Company, LLC.
DTC P2101 [MZI-3.7]
DTC P2101 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DIAGNOSTIC PROCEDURE
3.7].)
Are any DTCs present?
No
Troubleshooting completed.
DTC P2101
Throttle actuator circuit range/performance
DETECTION
CONDITION
A PCM malfunction flag is set indicating the motor circuit is open, and may
require cycling the key.
POSSIBLE CAUSE
Throttel actuator circuit are cross-wired
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 363
© 2005 Mitchell Repair Information Company, LLC.
DTC P2101 (MZI-3.7) DIAGNOSTIC PROCEDURE
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins and/or
on-line repair information availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
If the vehicle is not repaired, go to the
next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE
OR STORED DTCs FOR ALL OF
VEHICLE MODULE
Turn the ignition switch off then to the
ON position (Engine off).
Verify related pending code or stored
DTCs.
Is other DTCs present?
Yes
Go to the appropriate DTC troubleshooting. (See
DTC TABLE [MZI-3.7].)
No
Go to the next step.
4
INSPECT THROTTLE BODY AND
PCM CONNECTOR FOR POOR
CONNECTION
Turn the ignition switch off.
Disconnect the throttle body and PCM
connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Are there any malfunction?
Yes
Repair or replace suspected part, then go to Step
6.
No
Go to the next step.
5
INSPECT FOR CORRECT PCM
OPERATION
Disconnect all the PCM connectors.
Visually inspect for:
Pushed out pins
Corrosion
Connect all the PCM connectors and
verify that they seat correctly.
Retrieve DTCs using the M-MDS.
Yes Go to the next step.
No
The system is correctly. Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 364
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст