Mazda CX-9 Grand Touring. Manual — part 305
3
INSPECT PSP SWITCH CONNECTOR
FOR POOR CONNECTION
Turn the ignition switch off.
Disconnect the PCM connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Is there any malfunction?
Yes
Repair or replace suspected part, then go to
Step 8.
No
Go to the next step.
4
INSPECT PSP SWITCH CIRCUIT FOR
SHORT TO GROUND
Turn the ignition switch off.
Inspect for continuity between PSP
switch terminal A (wiring harness-side)
and body ground.
Is there continuity?
Yes
Repair or replace suspected part, then go to
Step 8.
No
Go to the next step.
5
INSPECT PCM CONNECTOR FOR
POOR CONNECTION
Turn the ignition switch off.
Disconnect the PCM connector.
Inspect for poor connection (such as
damaged/pulled-out pins, corrosion).
Is there any malfunction?
Yes
Repair or replace suspected part, then go to
Step 8.
No
Go to the next step.
6
INSPECT PSP SWITCH CIRCUIT FOR
OPEN CIRCUIT
Inspect for continuity between PSP
switch terminal A (wiring harness-side)
and PCM terminal 21 (wiring harness-
side)
Is there continuity?
Yes Go to the next step.
No
Repair or replace suspected part, then go to
Step 8.
7
INSPECT FOR CORRECT PCM
OPERATION
Disconnect all the PCM connectors.
Visually inspect for:
Pushed out pins
Corrosion
Connect all the PCM connectors and
verify that they seat correctly.
Retrieve DTCs using the M-MDS.
Yes Go to the next step.
No
The system is correctly. Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:41 AM
Page 353
© 2005 Mitchell Repair Information Company, LLC.
DTC P1674 [MZI-3.7]
DTC P1674 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DIAGNOSTIC PROCEDURE
DTC P1674 (MZI-3.7) DIAGNOSTIC PROCEDURE
Is the PENDING CODE for this DTC
present?
8
VERIFY TROUBLESHOOTING OF DTC
P1650 HAS BEEN COMPLETED
Verify that all disconnected connectors
reconnected.
Start the engine.
Clear DTC from PCM memory using
M-MDS.
Perform the "KOEO/KOER Self-Test".
(See KOEO/KOER SELF TEST
[MZI-3.7].)
Is same DTC present?
Yes
Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION
[MZI-3.7] .)
No
Go to the next step.
9
VERIFY AFTER REPAIR PROCEDURE
Perform "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See
DTC TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P1674
Control module software corrupted
DETECTION
CONDITION
Indicates that an error occurred in the PCM. This DTC is set in
combination with P2105.
POSSIBLE CAUSE
Software incompatibility issue
PCM malfunction
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED
Has FREEZE FRAME DATA been
recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to the next step.
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Yes
Perform repair or diagnosis according to the
available Service Bulletins.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:41 AM
Page 354
© 2005 Mitchell Repair Information Company, LLC.
DTC P1703 [MZI-3.7]
DTC P1703 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
2
Verify related Service Bulletins
and/or on-line repair information
availability.
Is any related Service Bulletins
available?
If the vehicle is not repaired, go to the next
step.
No
Perform the PCM reprogramming procedure. (See
PCM CONFIGURATION [MZI-3.7] .)Then go
to the next step.
3
VERIFY TROUBLESHOOTING OF
DTC P1674 HAS BEEN COMPLETED
Verify that all disconnected
connectors are reconnected.
Turn the ignition switch to the ON
position (Engine off).
Clear the DTC from the PCM
memory using the M-MDS.
Start the engine and perform the
KOEO and KOER self-test.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this
DTC present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
4
VERIFY AFTER REPAIR
PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P1703
Brake switch out of self-test range
DETECTION
CONDITION
Indicates that during the KOEO self-test, the brake pedal position signal was high,
or during the KOER self-test, the BPP signal did not cycle high and low.
POSSIBLE CAUSE
Connector or terminal malfunction
Brake switch No.1 malfunction
Brake switch No.1 misinstallation
Brake switch No.1 circuit malfunction
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:41 AM
Page 355
© 2005 Mitchell Repair Information Company, LLC.
DIAGNOSTIC PROCEDURE
DTC P1703 (MZI-3.7) DIAGNOSTIC PROCEDURE
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED
Has FREEZE FRAME DATA
been recorded?
Yes Go to next step.
No
Record FREEZE FRAME DATA on the repair
order, then go to next step.
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Yes
Perform repair or diagnosis according to available
Service Bulletins.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:42 AM
Page 356
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст