Mazda CX-9 Grand Touring. Manual — part 330
DIAGNOSTIC PROCEDURE
NO.5 ENGINE STALLS-AFTER START/AT IDLE (MZI-3.7) DIAGNOSTIC PROCEDURE
POSSIBLE
CAUSE
Fuel leakage from fuel injector
Fuel injector clogging
Ignition coil malfunction
Improper air/fuel mixture ratio control
Improper valve timing
Improper operation variable valve timing control system
Immobilizer system and/or circuit malfunction
Immobilizer system operating property. (Ignition key is not registered.)
Pressure regulator malfunction (built-in fuel pump unit)
WARNING:
The following troubleshooting flow chart contains the fuel system diagnosis
and repair procedures. Read the following warnings before servicing the fuel
system:
Fuel vapor is hazardous. It can easily ignite, causing serious injury
and damage. Always keep sparks and flames away from fuel.
Fuel line spills and leakage are dangerous. Fuel can ignite and cause
serious injuries or death and damage. Fuel can also irritate skin and
eyes. To prevent this, always complete "BEFORE SERVICE
PRECAUTION" and "AFTER SERVICE PRECAUTION" described in this
manual.
(See BEFORE SERVICE PRECAUTION [MZI-3.7] .)
(See AFTER SERVICE PRECAUTION [MZI-3.7] .)
CAUTION:
Disconnecting/connecting quick release connector without cleaning it
may cause damage to fuel pipe and quick release connector. Always
clean quick release connector joint area before
disconnecting/connecting, and make sure that it is free of foreign
material.
STEP
INSPECTION
RESULTS
ACTION
1
Connect the M-MDS to the DLC-2.
Do the following conditions appear?
The engine is not completely started.
DTC P1260 is displayed.
Yes
Both conditions appear:
Go to Step 3.
No
Either or other condition appears:
Go to the next step.
Yes
Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE Symptom Troubleshooting (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:10:05 AM
Page 26
© 2005 Mitchell Repair Information Company, LLC.
2
Does the engine stall after approx. 2 s
since the engine is started?
No
Immobilizer system is normal.
Go to Step 9.
3
Is coil connector securely connected to
coil?
Yes
Go to the next step.
No
Connect the coil connector securely.
Return to Step 2.
4
Does the security light flush?
Yes
Go to the next step.
No
Inspect and repair or replace the following:
Wiring harnesses and connectors
from keyless control module
terminal 3W and instrument cluster
terminal 1W
Wiring harness and connectors from
keyless control module terminal 3X
and instrument cluster terminal 1X
Instrument cluster
(See INSTRUMENT CLUSTER
INSPECTION .)
5
Connect the M-MDS to the DLC-2 and
retrieve DTC for PCM, instrument cluster
and keyless control module (with advanced
keyless entry system).
Are any of the following DTCs displayed?
DTC
PCM: B1342, U0073, U0155
Instrument cluster: B1213, B1600,
B1601, B1602, B1681, B2103, 2139,
B2431, U0110, U0214
Keyless control module (with advanced
keyless entry system): B1681, B2103,
B1213
Yes
Go to the appropriate DTC inspection.
(See DTC TABLE [MZI-3.7] .)
No
Go to the next step.
6
Inspect for the following wiring harnesses
and connectors:
With advanced keyless entry system:
Between coil terminal A and keyless
control module terminal 3V
Between coil terminal B and keyless
control module terminal 3U
Without advanced keyless entry system:
Yes
Repair or replace the suspected wiring
harness and connector.
Go to the next step, (with advanced
2008 Mazda CX-9 Grand Touring
2008 ENGINE Symptom Troubleshooting (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:10:05 AM
Page 27
© 2005 Mitchell Repair Information Company, LLC.
Between coil terminal A and
instrument cluster terminal 1G
Between coil terminal B and
instrument cluster terminal 1E
Is there any malfunction?
No
keyless entry system.)
Go to Step 8. (without advanced keyless
entry system.)
7
Inspect the following wiring harnesses and
connectors for an open or short circuit:
Between keyless control module
terminal 3W and instrument cluster
terminal 1W
Between keyless control module
terminal 3X and instrument cluster
terminal 1X
Is there any malfunction?
Yes
Repair or replace wiring harness and
connectors.
No
Go to the next step.
8
Inspect for the following wiring harnesses
and connectors:
Between PCM terminal 1BG and
instrument cluster terminal 1W
Between PCM terminal 1BL and
instrument cluster terminal 1X
Is there any malfunction?
Yes
Repair or replace the suspected wiring
harness and connector.
No
Go to the next step.
9
Verify the following:
Vacuum connection
Air cleaner element
No air leakage from intake-air
system
No restriction of intake-air system
Proper sealing of intake manifold
and components attached to intake
manifold
Ignition wiring
Fuel quality: proper octane,
contamination, winter/summer blend
Electrical connections
Yes
Go to the next step.
No
Service if necessary.
Repeat Step 9.
2008 Mazda CX-9 Grand Touring
2008 ENGINE Symptom Troubleshooting (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:10:05 AM
Page 28
© 2005 Mitchell Repair Information Company, LLC.
Smooth operation of throttle valve
Are all items normal?
10
Connect the M-MDS to the DLC-2.
Access the APP1 and APP2, APP3 PIDs.
Crank the engine with accelerator pedal
released.
Are the APP1 and APP2, APP3 PIDs
indicating that the accelerator pedal is in
the released position?
Yes
Go to the next step.
No
Inspect for the following:
APP sensor
Wiring harnesses and connectors for
following:
PCM terminal 1AC-APP
sensor terminal B
PCM terminal 1 AH-APP
sensor terminal C
PCM terminal 1Y-APP sensor
terminal D
PCM terminal 1AK-APP
sensor terminal E
PCM terminal 1BA-APP
sensor terminal F
PCM terminal 1 AD-APP
sensor terminal G
PCM terminal 1AG-APP
sensor terminal H
11
Connect the M-MDS to the DLC-2.
Access the TP1, TP2 PID. Crank the
engine with accelerator pedal released.
Are the TP1, TP2 PID indicates the closed
throttle position?
Yes
Go to the next step.
No
Inspect for the following:
TP sensor
Wiring harnesses and connectors for
following:
PCM terminal 2BO-TP sensor
terminal A
PCM terminal 2BR-TP sensor
terminal B
PCM terminal 2AD-TP sensor
terminal C
PCM terminal 2D-TP sensor
terminal D
PCM terminal 2AH-TP sensor
terminal E
PCM terminal 2Z-TP sensor
terminal F
2008 Mazda CX-9 Grand Touring
2008 ENGINE Symptom Troubleshooting (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:10:05 AM
Page 29
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст