Mazda CX-30 (2021 year). Manual in english — page 15
Maintenance and Care
Owner Maintenance
The system does not operate and the
3. Insert a tape-wrapped flathead
operation indicator light on the
screwdriver into the gap and slide it
transmitter does not flash when the
in the direction of the arrow.
buttons are pressed.
The system's operational range is
reduced.
Incorrect battery replacement
operation may damage the key.
Replacing the battery at an Authorized
Mazda Dealer is recommended. If
4. Twist the flathead screwdriver in the
replacing the battery by yourself,
direction of the arrow and remove
follow the instruction.
the upper cover.
Replacing the key battery
1. Remove the lower cover while
pressing the knob in the direction
of the arrow.
5. Remove the cap using the
tape-wrapped flathead screwdriver.
2. Press in the tab to unlock the upper
cover.
6. Remove the battery using
tape-wrapped flathead screwdriver.
6-30
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
7. Insert a new battery into the
Tires
transmitter so that the positive pole
is facing up.
▼ Tires
8. Install the cap.
For reasons of proper performance,
safety, and better fuel economy, always
maintain recommended tire inflation
pressures and stay within the
recommended load limits and weight
distribution.
WARNING
9. Install the upper cover.
Using Different Tire Types:
Driving your vehicle with different
types of tires is dangerous. It could
cause poor handling and poor braking;
leading to loss of control.
Except for the limited use of the
temporary spare tire, use only the
same type tires (radial, bias-belted,
bias-type) on all four wheels.
10.Insert the tabs of the lower cover
Using Wrong-Sized Tires:
into the slots of the transmitter and
Using any other tire size than what is
install the lower cover.
specified for the vehicle (page 9-8)
is dangerous. It could seriously affect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size specified for the
vehicle.
▼ Tire Inflation Pressure
WARNING
Always inflate the tires to the correct
pressure:
Overinflation or underinflation of tires
is dangerous. Adverse handling or
unexpected tire failure could result in a
serious accident.
Refer to Tires on page 9-8.
6-31
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
Use only a Mazda-genuine tire valve
▼ Tire Rotation
cap:
Use of a non-genuine part is
WARNING
dangerous as the correct tire air
pressure cannot be maintained if the
Rotate tires periodically:
tire valve becomes damaged. If the
Irregular tire wear is dangerous. To
vehicle is driven under this condition,
equalize tread wear for maintaining
the tire air pressure will decrease
good performance in handling and
which could result in a serious
braking, rotate the tires periodically or
accident. Do not use any part for the
sooner if irregular wear develops.
tire valve cap that is not a
Please refer to Scheduled maintenance
Mazda-genuine part.
for your tire rotation interval.
Inspect all tire pressures monthly
During rotation, inspect them for
(including the spare) when the tires are
correct balance.
cold. Maintain recommended
pressures for the best ride, handling,
and minimum tire wear.
Refer to the specification charts (page
9-8).
NOTE
Always check tire pressure when tires
are cold.
Warm tires normally exceed
recommended pressures. Do not
release air from warm tires to adjust
1. Forward
the pressure.
Do not include (TEMPORARY USE
Underinflation can cause reduced
ONLY) spare tire in rotation.
fuel economy, uneven and
accelerated tire wear, and poor
Also, inspect them for uneven wear
sealing of the tire bead, which will
and damage. Abnormal wear is usually
deform the wheel and cause
caused by one or a combination of the
separation of tire from rim.
following:
Overinflation can produce a harsh
Incorrect tire pressure
ride, uneven and accelerated tire
Improper wheel alignment
wear, and a greater possibility of
Out-of-balance wheel
damage from road hazards.
Severe braking
Keep your tire pressure at the correct
levels. If one frequently needs
inflating, have it inspected.
After rotation, inflate all tire pressures
to specification on page 9-8 and
inspect the lug nuts for tightness.
6-32
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
3. Tread wear indicator
CAUTION
Rotate unidirectional tires and radial
You should replace the tire before the
tires that have an asymmetrical tread
band crosses the entire tread.
pattern or studs only from front to rear,
NOTE
not from side to side. Tire performance
Tires degrade over time, even when
will be reduced if rotated from side to
they are not being used on the road. It
side.
is recommended that tires generally be
replaced when they are 6 years or
▼ Replacing a Tire
older. Heat caused by hot climates or
frequent high loading conditions can
WARNING
accelerate the aging process. You
should replace the spare tire when you
Always use tires that are in good
replace the other road tires due to the
condition:
aging of the spare tire. The period in
Driving with worn tires is dangerous.
which the tire was manufactured (both
Reduced braking, steering, and
week and year) is indicated by a 4-digit
traction could result in an accident.
number.
Refer to Tire Labeling on page 8-24.
Replace all four tires at the same
time:
▼ Temporary Spare Tire
Replacing just one tire is dangerous. It
Inspect the temporary spare tire at
could cause poor handling and poor
least monthly to make sure it is
braking resulting in loss of vehicle
properly inflated and stored.
control. Mazda strongly recommends
that you replace all four tires at the
NOTE
same time.
The temporary spare tire condition
gradually deteriorates even if it has not
If a tire wears evenly, a wear indicator
been used.
will appear as a solid band across the
tread.
The temporary spare tire is easier to
Replace the tire when this happens.
handle because of its construction
which is lighter and smaller than a
conventional tire. This tire should be
used only for an emergency and only
for a short distance.
Use the temporary spare tire only until
the conventional tire is repaired, which
should be as soon as possible.
Refer to Tires on page 9-8.
1. New tread
2. Worn tread
6-33
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
CAUTION
CAUTION
¾ Do not use your temporary spare tire
A wrong-sized wheel may adversely
rim with a snow tire or a
affect:
conventional tire. Neither will
¾ Tire fit
properly fit and could damage both
¾ Wheel and bearing life
tire and rim.
¾ Ground clearance
¾ The temporary spare tire has a tread
¾ Snow-chain clearance
life of less than 5,000 km (3,000
¾ Speedometer calibration
miles). The tread life may be shorter
¾ Headlight aim
depending on driving conditions.
¾ Bumper height
¾ The temporary spare tire is for
¾ Tire Pressure Monitoring System
limited use, however, if the tread
wear solid-band indicator appears,
NOTE
replace the tire with the same type of
temporary spare (page 6-33).
When replacing a wheel, make sure
the new one is the same as the
NOTE
original factory wheel in diameter,
Tires degrade over time, even when
rim width, and offset (inset/outset).
they are not being used on the road. It
For details, contact an Authorized
is recommended that tires generally be
Mazda Dealer.
replaced when they are 6 years or
older. Heat caused by hot climates or
Proper tire balancing provides the best
frequent high loading conditions can
riding comfort and helps reduce tread
accelerate the aging process. You
wear. Out-of-balance tires can cause
should replace the spare tire when you
vibration and uneven wear, such as
replace the other road tires due to the
cupping and flat spots.
aging of the spare tire. The period in
which the tire was manufactured (both
week and year) is indicated by a 4-digit
number.
Refer to Tire Labeling on page 8-24.
▼ Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling could
be affected, leading to loss of control
and an accident.
6-34
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
Light Bulbs
Fuses
▼ Replacing Light Bulbs
▼ Fuses
All the light bulbs are the LED type.
Your vehicle's electrical system is
The LED bulb cannot be replaced as a
protected by fuses.
single unit because it is an integrated
unit.
If any lights, accessories, or controls do
The LED bulb has to be replaced with
not work, inspect the appropriate
the unit. We recommend an
circuit protector. If a fuse has blown,
Authorized Mazda Dealer when the
the inside element will be melted.
replacement is necessary.
If the same fuse blows again, avoid
using that system and consult an
Authorized Mazda Dealer as soon as
possible.
▼ Fuse Replacement
Replacing the fuses on the vehicle's
left side
If the electrical system does not work,
first inspect the fuses on the vehicle's
left side.
1. Make sure the ignition is switched
off, and other switches are off.
2. Open the fuse panel cover.
6-35
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
3. Pull the fuse straight out with the
Replacing the fuses under the hood
fuse puller provided on the fuse
If the headlights or other electrical
block located in the engine
components do not work and the fuses
compartment.
in the cabin are normal, inspect the
fuse block under the hood.
If a fuse is blown, it must be replaced.
Follow these steps:
1. Make sure the ignition is switched
off, and other switches are off.
2. Remove the fuse block cover.
4. Inspect the fuse and replace it if it is
blown.
1. Normal
3. If any fuse but the MAIN fuse is
2. Blown
blown, replace it with a new one of
the same amperage rating.
5. Insert a new fuse of the same
amperage rating, and make sure it
fits tightly. If it does not fit tightly,
have an expert install it. Consult an
Authorized Mazda Dealer.
If you have no spare fuses, borrow
one of the same rating from a
circuit not essential to vehicle
operation, such as the audio or
1. Normal
accessory socket circuit.
2. Blown
CAUTION
Always replace a fuse with a
genuine Mazda fuse or equivalent
of the same rating. Otherwise, you
may damage the electric system.
6. Reinstall the cover and make sure
that it is securely installed.
6-36
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
WARNING
Do not replace the main fuse by
yourself. Have an Authorized
Mazda Dealer perform the
replacement:
Replacing the fuse by yourself is
dangerous because the MAIN fuse
is a high current fuse. Incorrect
replacement could cause an
electrical shock or a short circuit
resulting in a fire.
4. Reinstall the cover and make sure
that it is securely installed.
6-37
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
▼ Fuse Panel Description
Fuse block (Engine compartment)
FUSE RAT-
No.
PROTECTED COMPONENT
ING
F1
―
―
F2
20 A
Windshield wiper de-icer*
30 A
Engine control system
F3
20 A
―
F4
20 A
S-VT
F5
40 A
Engine control system
F6
20 A
―
6-38
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
FUSE RAT-
No.
PROTECTED COMPONENT
ING
15 A
―
F7
20 A
Fuel pump
F8
15 A
Engine control system
F9
15 A
Transmission control system*
F10
15 A
Engine control system
F11
7.5 A
Air conditioner
F12
15 A
Engine control system
F13
15 A
―
F14
20 A
Front seat warmer*
F15
20 A
―
F16
15 A
For protection of various circuits
F17
―
―
F18
15 A
For protection of various circuits
F19
60 A
Power steering system
F20
15 A
Headlight (LH) 1
F21
15 A
Headlight (RH) 1
F22
15 A
Keyless system
F23
30 A
ABS, Dynamic stability control system
F24
15 A
Headlight (LH) 2
F25
15 A
Headlight (RH) 2
F26
7.5 A
On board diagnostics
F27
25 A
For protection of various circuits
F28
25 A
For protection of various circuits
F29
15 A
Windshield washer
F30
15 A
Accessory sockets
F31
15 A
Horn
F32
15 A
Headlights
F33
―
―
F34
―
―
F35
50A
ABS, Dynamic stability control system
F36
―
―
F37
40 A
Rear window defogger
F38
50 A
For protection of various circuits
*Some models.
6-39
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
FUSE RAT-
No.
PROTECTED COMPONENT
ING
F39
―
―
F40
40 A
Air conditioner
F41
―
―
F42
20 A
Windshield wipers
F43
30 A
Cooling fan
F44
30 A
Starter
F45
10 A
Engine control system
F46
15 A
Audio
F47
15 A
For protection of various circuits
F48
7.5 A
Air bag
F49
15 A
Instrument cluster
F50
15 A
Room light
F51
25 A
Audio
F52
10 A
Moonroof*
F53
15 A
Engine control system
F54
15 A
i-ACTIVSENSE
F55
50 A
―
F56
50 A
―
6-40
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
Fuse block (Left side)
FUSE RAT-
No.
PROTECTED COMPONENT
ING
F1
―
―
F2
―
―
F3
―
―
F4
15 A
Power door locks (Driver)
F5
15 A
Power door locks (Passenger)
F6
―
―
F7
25 A
Power liftgate*
F8
―
―
F9
30 A
Power windows (Driver)
F10
30 A
Power windows (Passenger)
F11
30 A
Power seat (Driver)*
F12
―
―
F13
15 A
Audio
F14
―
―
F15
15 A
Liftgate lock
*Some models.
6-41
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Owner Maintenance
FUSE RAT-
No.
PROTECTED COMPONENT
ING
F16
15 A
Illumination
F17
10 A
Brake lights
F18
10 A
Reverse lights
F19
10 A
Rear turn signal lights
F20
10 A
Taillights
F21
10 A
Taillights
F22
7.5 A
Air bag*
F23
―
―
6-42
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
Damage Caused by Bird Dropping,
Exterior Care
Insects, or Tree Sap
▼ Exterior Care
Occurrence
The paintwork on your Mazda
Bird droppings contain acids. If these
represents the latest technical
are not removed they can eat away the
developments in composition and
clear and color base coat of the
methods of application.
vehicle's paintwork.
Environmental hazards, however, can
When insects stick to the paint surface
harm the paint's protective properties,
and decompose, corrosive compounds
if proper care is not taken.
form. These can erode the clear and
color base coat of the vehicle's
Here are some examples of possible
paintwork if they are not removed.
damage, with tips on how to prevent
them.
Tree sap will harden and adhere
permanently to the paint finish. If you
Etching Caused by Acid Rain or
scratch the sap off while it is hard,
Industrial Fallout
some vehicle paint could come off
Occurrence
with it.
Industrial pollutants and vehicle
Prevention
emissions drift into the air and mix
It is necessary to have your Mazda
with rain or dew to form acids. These
washed and waxed to preserve its
acids can settle on a vehicle's finish. As
finish according to the instructions in
the water evaporates, the acid
this section. This should be done as
becomes concentrated and can
soon as possible.
damage the finish.
And the longer the acid remains on the
Bird droppings can be removed with a
surface, the greater the chance is for
soft sponge and water. If you are
damage.
traveling and these are not available, a
Prevention
moistened tissue may also take care of
the problem. The cleaned area should
It is necessary to wash and wax your
be waxed according to the instructions
vehicle to preserve its finish according
in this section.
to the instructions in this section.
Insects and tree sap are best removed
These steps should be taken
with a soft sponge and water or a
immediately after you suspect that acid
commercially available chemical
rain has settled on your vehicle's finish.
cleaner.
Another method is to cover the
affected area with dampened
newspaper for 1 to 2 hours. After
removing the newspaper, rinse off the
loosened debris with water.
6-43
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
Water Marks
Chipped paint can lead to rust
forming on your Mazda. Before this
Occurrence
happens, repair the damage by using
Rain, fog, dew, and even tap water can
Mazda touch-up paint according to
contain harmful minerals such as salt
the instructions in this section.
and lime. If moisture containing these
Failure to repair the affected area
minerals settles on the vehicle and
could lead to serious rusting and
evaporates, the minerals will
expensive repairs.
concentrate and harden to form white
rings. The rings can damage your
Follow all label and container
vehicle's finish.
directions when using a chemical
Prevention
cleaner or polish. Read all warnings
and cautions.
It is necessary to wash and wax your
vehicle to preserve its finish according
▼ Maintaining the Finish
to the instructions in this section.
Washing
These steps should be taken
immediately after you find water marks
on your vehicle's finish.
CAUTION
Paint Chipping
¾ Before lifting the windshield wiper
blades off the windshield, always
Occurrence
follow the procedure for moving the
Paint chipping occurs when gravel
windshield wiper blades. Otherwise,
thrown in the air by another vehicle's
a wiper blade, wiper arm, or the
tires hits your vehicle.
hood could be damaged.
Refer to the Replacing Windshield
How to avoid paint chipping
Wiper Blades (page 6-23) section for
Keeping a safe distance between you
the procedure on how to move the
and the vehicle ahead reduces the
windshield wiper blades to the
chances of having your paint chipped
service position.
by flying gravel.
¾ When the ignition is switched ON
and the wiper lever is in the AUTO
NOTE
position, the windshield wipers may
The paint chipping zone varies with
operate automatically in the
the speed of the vehicle. For
following cases:
example, when traveling at 90 km/h
(56 mph), the paint chipping zone is
¾ The area of the windshield above
the rain sensor is touched or wiped
50 m (164 ft).
In low temperatures a vehicle's finish
with a cloth.
¾ The windshield or the rain sensor
hardens. This increases the chance of
paint chipping.
area in the cabin is hit.
6-44
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
When the ignition is switched ON
Scratches occur on the paint surface
and the wiper lever is in the AUTO
when:
position, do not touch the
The vehicle is washed without first
windshield or the windshield wipers
rinsing off dirt and other foreign
Otherwise, the windshield wipers
matter.
will operate automatically which
The vehicle is washed with a rough,
could catch your fingers or damage
dry, or dirty cloth.
the windshield wipers.
The vehicle is washed at a car wash
When removing ice or snow, or
that uses brushes that are dirty or too
cleaning the windshield, always
stiff.
make sure the wiper lever is in the
Cleansers or wax containing
OFF position.
abrasives are used.
¾ Do not spray water in the engine
compartment. Otherwise, it could
NOTE
result in engine-starting problems or
Mazda is not responsible for
damage to electrical parts.
scratches caused by automatic car
¾ When washing and waxing the
washes or improper washing.
vehicle, be careful not to apply
Scratches are more noticeable on
excessive force to any single area of
vehicles with darker paint finishes.
the vehicle roof or the antenna.
Otherwise, you could dent the
To minimize scratches on the vehicle's
vehicle or damage the antenna.
paint finish:
¾ Make sure that the fuel-filler lid is
Rinse off any dirt or other foreign
closed and lock the doors.
matter using lukewarm or cold water
Otherwise, the fuel-filler lid may be
before washing.
forcefully opened by water pressure
Use plenty of lukewarm or cold
causing damage to the vehicle or
water and a soft cloth when washing
fuel-filler lid.
the vehicle. Do not use a nylon cloth.
To help protect the finish from rust and
Rub gently when washing or drying
deterioration, wash your Mazda
the vehicle.
thoroughly and frequently, at least
Take your vehicle only to a car wash
once a month, with lukewarm or cold
that keeps its brushes well
water.
maintained.
Do not use abrasive cleansers or wax
If the vehicle is washed improperly, the
that contain abrasives.
paint surface could be scratched. Here
are some examples of how scratching
could occur.
6-45
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
When using an automatic car wash
CAUTION
Retract the door mirrors.
¾ Do not use steel wool, abrasive
The automatic car wash brushes
cleaners, or strong detergents
could reduce the paint lustre or
containing highly alkaline or caustic
hasten paint deterioration.
agents on chrome-plated or
anodized aluminum parts. This may
When using a high water pressure car
damage the protective coating; also,
wash
cleaners and detergents may discolor
High water temperature and high
or deteriorate the paint.
water pressure car washers are
Pay special attention to removing salt,
available depending on the type of car
dirt, mud, and other foreign material
wash machine. If the car washer nozzle
from the underside of the fenders, and
is put too close to the vehicle, the
make sure the drain holes in the lower
force of the spray could damage or
edges of the doors and rocker panels
deform the molding, affect the
are clean.
sealability of parts, and allow water to
penetrate the interior. Keep a sufficient
Insects, tar, tree sap, bird droppings,
space (30 cm (12 in) or more)
industrial fallout, and similar deposits
between the nozzle and the vehicle. In
can damage the finish if not removed
addition, do not spend too much time
immediately. When prompt washing
spraying the same area of the vehicle,
with plain water is ineffective, use a
and be very careful when spraying
mild soap made for use on vehicles.
between gaps in doors and around
windows.
Thoroughly rinse off all soap with
Waxing
lukewarm or cold water. Do not allow
soap to dry on the finish.
Your vehicle needs to be waxed when
water no longer beads on the finish.
After washing the vehicle, dry it with a
Always wash and dry the vehicle before
clean chamois to prevent water spots
waxing it. In addition to the vehicle
from forming.
body, wax the metal trim to maintain
its luster.
WARNING
1. Use wax which contains no
Dry off brakes that have become wet
abrasives.
by driving slowly, releasing the
Wax containing abrasives will
accelerator pedal and lightly applying
remove paints and could damage
the brakes several times until the
bright metal parts.
brake performance returns to normal:
2. Use a good grade of natural wax for
Driving with wet brakes is dangerous.
metallic, mica, and solid colors.
Increased stopping distance or the
3. When waxing, coat evenly with the
vehicle pulling to one side when
sponge supplied or a soft cloth.
braking could result in a serious
4. Wipe off the wax with a soft cloth.
accident. Light braking will indicate
whether the brakes have been
affected.
6-46
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
NOTE
CAUTION
A spot remover to remove oil, tar, and
similar materials will usually also take
Do not use steel wool, abrasive
off the wax. Rewax these areas even if
cleaners, or strong detergents
the rest of the vehicle does not need it.
containing highly alkaline or caustic
agents on chrome-plated or anodized
▼ Repairing Damage to the Finish
aluminum parts. This may result in
Deep scratches or chips on the finish
damage to the protective coating and
should be repaired promptly. Exposed
cause discoloration or paint
metal quickly rusts and can lead to
deterioration.
major repairs.
▼ Underbody Maintenance
CAUTION
Road chemicals and salt used for ice
and snow removal and solvents used
If your Mazda is damaged and needs
for dust control may collect on the
metal parts repaired or replaced, make
underbody. If not removed, they will
sure the body shop applies
speed up rusting and deterioration of
anti-corrosion materials to all parts,
such underbody parts as fuel lines,
both repaired and new. This will
frame, floor pan, and exhaust system,
prevent them from rusting.
even though these parts may be coated
▼ Bright-Metal Maintenance
with anti-corrosive material.
Use tar remover to remove road tar
Thoroughly flush the underbody and
and insects. Never do this with a
wheel housings with lukewarm or cold
knife or similar tool.
water at the end of each winter. Try
To prevent corrosion on bright-metal
also to do this every month.
surfaces, apply wax or chrome
preservative and rub it to a high
Pay special attention to these areas
luster.
because they easily hide mud and dirt.
During cold weather or in coastal
It will do more harm than good to wet
areas, cover bright-metal parts with a
down the road grime without
coating of wax or preservative
removing it.
heavier than usual. It would also help
to coat them with noncorrosive
The lower edges of doors, rocker
petroleum jelly or some other
panels, and frame members have drain
protective compound.
holes that should not be clogged.
Water trapped there will cause rusting.
6-47
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
▼ Plastic Part Maintenance
WARNING
When cleaning the plastic lenses of
Dry off brakes that have become wet
the lights, do not use gasoline,
by driving slowly, releasing the
kerosene, rectified spirit, paint,
accelerator pedal and lightly applying
thinner, highly acidic detergents, or
the brakes several times until the
strongly alkaline detergents.
brake performance returns to normal:
Otherwise, these chemical agents
Driving with wet brakes is dangerous.
can discolor or damage the surfaces
Increased stopping distance or the
resulting in a significant loss in
vehicle pulling to one side when
functionality. If plastic parts become
braking could result in a serious
inadvertently exposed to any of these
accident. Light braking will indicate
chemical agents, flush with water
whether the brakes have been
immediately.
affected.
If plastic parts such as the bumpers
become inadvertently exposed to
▼ Aluminum Wheel Maintenance*
chemical agents or fluids such as
A protective coating is provided over
gasoline, oil, engine coolant, or
the aluminum wheels. Special care is
battery fluid, it could cause
needed to protect this coating.
discoloration, staining, or paint
peeling. Wipe off any such chemical
CAUTION
agents or fluids using a soft cloth
immediately.
Do not use any detergent other than
High water temperature and high
mild detergent. Before using any
water pressure car washers are
detergent, verify the ingredients.
available depending on the type of
Otherwise, the product could discolor
high pressure car washer device. If
or stain the aluminum wheels.
the car washer nozzle is put too
close to the vehicle or aimed at one
NOTE
area for an extended period of time,
it could deform plastic parts or
Do not use a wire brush or any
damage the paint.
abrasive cleaner, polishing
Do not use wax containing
compound, or solvent on aluminum
compounds (polish). Otherwise, it
wheels. They may damage the
could result in paint damage.
coating.
In addition, do not use an electrical
Always use a sponge or soft cloth to
or air tool to apply wax. Otherwise,
clean the wheels.
the frictional heat generated could
Rinse the wheels thoroughly with
result in deformation of plastic parts
lukewarm or cold water. Also, be
or paint damage.
sure to clean the wheels after driving
on dusty or salted roads to help
prevent corrosion.
Avoid washing your vehicle in an
automatic car wash that uses
high-speed or hard brushes.
6-48
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
▼ Seat Belt Maintenance
Interior Care
1. Clean the soiled area by lightly
▼ Interior Care
dabbing it with a soft cloth soaked
in a mild detergent (approx. 5%)
WARNING
diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
Do not spray water into the vehicle
and wrung out well.
cabin:
3. Before retracting seat belts which
Spraying water into the vehicle cabin is
have been pulled out for cleaning,
dangerous as electrical devices such as
dry them off thoroughly and make
the audio and switches could get wet
sure there is no remaining moisture
resulting in a malfunction or vehicle
on them.
fire.
WARNING
NOTE
Do not wipe the interior using
If a seat belt appears frayed or has
alcohol, chlorine bleach, or organic
abrasions, have it replaced by an
solvents such as thinner, benzene,
Authorized Mazda Dealer:
and gasoline. Otherwise, it may
If a seat belt is used under such a
cause discoloration or stains.
condition, it cannot function at its full
Rubbing hard with a stiff brush or
capacity which could result in serious
cloth may cause damage.
injury or death.
If the vehicle interior becomes soiled
Use a mild detergent to remove
by any of the following, wipe it off
soiling from a seat belt:
immediately using a soft cloth.
If organic solvents are used for cleaning
Leaving it uncleaned could cause
the seat belts or they become stained
discoloration, stains, cracks, or peeling
or bleached, there is the possibility of
of the coating, and it will make it hard
them becoming weakened and as a
to wipe off later.
result, they may not function at their
Beverage or fragrance
full capacity which could cause serious
Grease or oil
injury or death.
Soiling
NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will
make it difficult to clean them later,
and it may affect the smooth retracting
of the seat belt.
6-49
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
▼ Vinyl Upholstery Maintenance
If the leather upholstery comes into
contact with any of the following,
Remove dust and dirt from the vinyl
clean it immediately.
upholstery using a brush or vacuum.
Leaving it uncleaned could cause
Remove soiling from vinyl upholstery
premature wear, mold, or stains.
using a leather and vinyl upholstery
cleaner.
Sand or dirt
Grease or oil, such as hand cream
▼ Upholstery Maintenance
Alcohol, such as in cosmetic or
hair dressing items
1.
Clean the soiled area by lightly
If the leather upholstery gets wet,
dabbing it with a soft cloth soaked
promptly remove moisture with a dry
in a mild detergent (approx. 5%)
cloth. Remaining moisture on the
diluted with water.
surface may cause deterioration such
2.
Wipe off the remaining detergent
as hardening and shrinkage.
using a cloth soaked in clean water
Exposure to direct sunlight for long
and wrung out well.
periods may cause deterioration and
▼ Leather Upholstery Maintenance*
shrinkage. When parking the car
under direct sunlight for long
1.
Remove dust and sand using a
periods, shade the interior using
vacuum cleaner.
sunshades.
2.
Wipe off the soiled area with a soft
Do not leave vinyl products on the
cloth and a suitable, special cleaner
leather upholstery for long periods.
or a soft cloth soaked in a mild
They may affect the leather quality
detergent (about 5%) diluted with
and coloring. If the cabin
water.
temperature becomes hot, the vinyl
3.
Wipe off the remaining detergent
may deteriorate and adhere to the
using a cloth soaked in clean water
genuine leather.
and wrung out well.
4.
Remove moisture with a dry, soft
▼ Plastic Part Maintenance
cloth and allow the leather to
further dry in a well-ventilated,
CAUTION
shaded area. If the leather gets wet
such as from rain, remove the
Do not use polishing agents.
moisture and dry it as soon as
Depending on the product ingredients,
possible.
they could cause discoloration, stains,
cracks or peeling of the coating.
NOTE
Because genuine leather is a natural
▼ Instrument Panel Top (Soft pad)
material, its surface is not uniform
Maintenance
and it may have natural scars,
Extremely soft material is used for the
scratches, and wrinkles.
soft pad surface. If the soft pad surface
To maintain the quality for as long as
is rubbed harshly with a dry cloth, it
possible, periodical maintenance,
could result in the surface being
about twice a year, is recommended.
damaged and leaving white scratch
marks.
6-50
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Maintenance and Care
Appearance Care
1. Wipe the soiled area with a soft
▼ Cleaning the Window Interiors
cloth soaked in a mild detergent
If the windows become covered with
(approx. 5%) diluted with water.
an oily, greasy, or waxy film, clean
2. Wipe off the remaining detergent
them with glass cleaner. Follow the
using a cloth soaked in clean water
directions on the container.
and wrung out well.
▼ Active Driving Display
CAUTION
Maintenance*
¾ Do not scrape or scratch the inside
The dust-proof sheet has a coating.
of the window glass. It could
When cleaning, do not use a hard or
damage the thermal filaments and
rough-surface cloth, or cleaning
the antenna lines.
detergent. In addition, if a chemical
¾ When washing the inside of the
solvent gets on the active driving
window glass, use a soft cloth
display, wipe it off immediately. The
dampened in lukewarm water, gently
dust-proof sheet could be damaged
wiping the thermal filaments and the
and the surface coating could be
antenna lines.
scratched. Use a fine, soft cloth such as
Use of glass cleaning products could
those used for cleaning eyeglasses.
damage the thermal filaments and
the antenna lines.
NOTE
Use of compressed air when cleaning
▼ Cleaning the Floor Mats
the dust-proof sheet is recommended.
Rubber floor mats should be cleaned
▼ Panel Maintenance
with mild soap and water only.
If a panel becomes soiled, wipe it off
WARNING
with a soft cloth soaked in clean water
and thoroughly wrung out.
Do not use rubber cleaners, such as
If some areas require further cleaning,
tire cleaner or tire shine, when
use the following procedure:
cleaning rubber floor mats:
1. Wipe the soiled area with a soft
Cleaning the rubber floor mats with
cloth soaked in a mild detergent
rubber cleaning products makes the
(approx. 5 %) diluted with water.
floor mats slippery.
2. Wipe off the remaining detergent
This may cause an accident when
using a cloth soaked in clean water
depressing the accelerator, brake, or
and wrung out well.
clutch (Manual transmission) pedal or
NOTE
when getting in or out of the vehicle.
Be particularly careful when cleaning
After removing the floor mats for
shiny surface panels and metallic parts
cleaning, always reinstall them securely
such as plating as they can be
(page 3-51).
scratched easily.
*Some models.
6-51
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
MEMO
6-52
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
7
Helpful information on what to do if a problem arises with the
vehicle.
Parking in an Emergency
7-2
Warning/Indicator Lights and
Parking in an Emergency
7-2
Warning Sounds
7-22
If a Warning Light Turns On or
Flashes
7-22
Flat Tire
7-3
Message Indicated on Multi-
Spare Tire and Tool Storage
information Display
7-34
. . . . . . . . . . . 7-3
Warning Sound is
Changing a Flat Tire
7-5
Activated
7-37
Battery Runs Out
7-13
When Liftgate Cannot be
Jump-Starting
7-13
Opened
7-43
When Liftgate Cannot be
Emergency Starting
7-16
Opened
7-43
Starting a Flooded Engine
7-16
Push-Starting
7-16
Active Driving Display Does Not
Operate
7-44
Overheating
7-17
If the Active Driving Display Does
Overheating
7-17
Not Operate*
7-44
Emergency Towing
7-19
Windshield Wipers Operate at High
Towing Description
7-19
Speed
7-45
Tiedown Hooks*
7-20
Windshield Wipers Operate at
High Speed
7-45
*Some models.
7-1
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
▼ Parking in an Emergency
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffic
hazard and that they must take
extreme caution when near it.
Depress the hazard warning flasher
and all the turn signals will flash. The
hazard warning indicator lights in the
instrument cluster flash simultaneously.
NOTE
The turn signals do not work when
the hazard warning lights are on.
Check local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
7-2
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
▼ Jack
Spare Tire and Tool
To remove the jack
Storage
1. Remove the luggage mat.
▼ Spare Tire and Tool Storage
Spare tire and tools are stored in the
locations illustrated in the diagram.
Type A
2. Remove the jack.
1. Jack lever
2. Spare tire hold-down bolt
3. Tiedown eyelet*
4. Jack
5. Spare tire
6. Flat tire bolt
7. Lug wrench
To secure the jack
Type B
Perform the removal procedure in
reverse.
Maintenance
Always keep the jack clean.
Make sure the moving parts are kept
free from dirt or rust.
Make sure the screw thread is
adequately lubricated.
▼ Spare Tire
1. Jack lever
Your Mazda has a temporary spare tire.
2. Spare tire hold-down bolt
The temporary spare tire is lighter and
3. Tiedown eyelet*
smaller than a conventional tire, and is
4. Jack
designed only for emergency use and
5. Spare tire
should be used only for VERY short
6. Lug wrench
periods. Temporary spare tires should
NEVER be used for long drives or
extended periods.
*Some models.
7-3
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
To remove the spare tire
WARNING
1.
Remove the luggage mat.
Do not install the temporary spare tire
on the front wheels (driving wheels):
Driving with the temporary spare tire
on one of the front driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tire to the front wheel and install the
temporary spare tire to the rear.
2.
(Vehicles with sub-woofer)
Uncouple the sub-woofer
CAUTION
connector.
¾ When using the temporary spare tire,
driving stability may decrease
compared to when using only the
conventional tire. Drive carefully.
¾ To avoid damage to the temporary
spare tire or to the vehicle, observe
the following precautions:
¾ Do not exceed 80 km/h (50 mph).
¾ Avoid driving over obstacles. Also,
do not drive through an automatic
car wash. This tire's diameter is
smaller than a conventional tire, so
the ground clearance is reduced.
NOTE
¾ Do not use a tire chain on this tire
Extra strength may be required to
because it will not fit properly.
uncouple the connector. Be sure to
¾ Do not use your temporary spare
squeeze the tab firmly.
tire on any other vehicle, it has
3.
(Vehicles with sub-woofer)
been designed only for your
Turn the spare tire hold-down bolt
Mazda.
counterclockwise and remove the
¾ Use only one temporary spare tire
sub-woofer and the spare tire.
on your vehicle at the same time.
7-4
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
(Vehicles without sub-woofer)
Changing a Flat Tire
Turn the spare tire hold-down bolt
counterclockwise and remove the
▼ Changing a Flat Tire
spare tire.
NOTE
If the following occurs while driving, it
could indicate a flat tire.
Steering becomes difficult.
The vehicle begins to vibrate
excessively.
The vehicle pulls in one direction.
If you have a flat tire, drive slowly to a
level spot that is well off the road and
out of the way of traffic to change the
1. Spare tire hold-down bolt
tire.
Stopping in traffic or on the shoulder
NOTE
of a busy road is dangerous.
If the spare tire hold-down bolt
cannot be loosened, hold the edge
WARNING
of the tire and turn it
counterclockwise until the spare
Be sure to follow the directions for
tire hold-down bolt rotates.
changing a tire:
Changing a tire is dangerous if not
To secure the spare tire
done properly. The vehicle can slip off
Store the spare tire in the reverse order
the jack and seriously injure someone.
of removal. After storing, verify that the
No person should place any portion of
spare tire is stored securely.
their body under a vehicle that is
supported by a jack.
Never allow anyone inside a vehicle
supported by a jack:
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
NOTE
Make sure the jack is well lubricated
before using it.
1. Park on a hard, level surface off the
right-of-way and firmly set the
parking brake.
7-5
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
2.
Put a vehicle with an automatic
▼ Removing a Flat Tire
transmission in Park (P), a manual
transmission in Reverse (R) or 1,
WARNING
and turn off the engine.
3.
Turn on the hazard warning flasher.
When jacking-up a vehicle, always
4.
Have passengers get out of the
shift the shift lever to 1st or R position
vehicle and away from the vehicle
(manual transmission vehicle) or shift
and traffic.
the selector lever to P position
5.
Remove any luggage, the jack,
(automatic transmission vehicle),
tools, and spare tire (page 7-3).
apply the parking brake, and place
6.
Block the wheel diagonally
wheel blocks in the position
opposite the flat tire. When
diagonally opposed to the jack:
blocking a wheel, place a tire block
Changing a flat tire without using
both in front and behind the tire.
wheel blocks is dangerous because the
vehicle may move and fall off the jack
even with the shift lever in 1st or R
position, or the selector lever is in P
position, which could result in an
accident.
1. If your vehicle is equipped with a
wheel cover, pry off the wheel
cover with the beveled end of the
jack lever.
NOTE
When blocking a tire, use rocks or
wood blocks of sufficient size if
possible to hold the tire in place.
NOTE
Force the end of the jack lever
firmly between wheel and cover, or
removal will be difficult.
7-6
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
3. Place the jack on the ground.
CAUTION
4. Turn the jack screw in the direction
Align the notch on the wheel cover
shown in the figure and adjust the
with the valve stem when installing
jack head so that it is close to the
it.
jack-up position.
1. Jack head
1. Notch
5. Place the jack under the jack-up
2. Tire valve
position closest to the tire being
changed with the jack head
Damage could occur during
squarely under the jack-up point.
installation if the wheel cover is not
properly aligned.
2. Loosen the lug nuts by turning them
counterclockwise one turn each,
but do not remove any lug nuts
until the tire has been raised off the
ground.
1. Jacking position
NOTE
If your Mazda is equipped with the
optional antitheft wheel lug nuts, a
special key must be used to unlock
the locking lug nut for each wheel.
For details, refer to the Locking Lug
Nuts on page 7-10.
7-7
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
6.
Continue raising the jack head
Do not jack up the vehicle in a
gradually by rotating the screw with
position other than the designated
your hand until the jack head is
jack-up position or place any
inserted into the jack-up position.
objects on or under the jack:
Jacking up the vehicle in a position
other than the designated jack-up
position or placing objects on or
under the jack is dangerous as it
could deform the vehicle body or
the vehicle could fall off the jack
resulting in an accident.
Use only the jack provided with
your Mazda:
Using a jack that is not designed for
your Mazda is dangerous. The
vehicle could slip off the jack and
seriously injure someone.
1. Tire blocks
Never place objects under the
2. Jacking position
jack:
Jacking the vehicle with an object
WARNING
under the jack is dangerous. The
jack could slip and someone could
Use only the front and rear jacking
be seriously injured by the jack or
positions recommended in this
the falling vehicle.
manual:
Attempting to jack the vehicle in
NOTE
positions other than those
When raising the jack head into the
recommended in this manual is
jacking position and aligning the
dangerous. The vehicle could slip
groove in the jack head with the rail
off the jack and seriously injure or
under the vehicle body, the top of
even kill someone. Use only the
the jack head contacts the vehicle's
front and rear jacking positions
underbody without the rail
recommended in this manual.
contacting the bottom of the
groove.
7-8
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
If Trouble Arises
Flat Tire
7.
Insert the jack lever and attach the
WARNING
lug wrench to tire jack.
Do not jack up the vehicle higher
than is necessary:
Jacking up the vehicle higher than is
necessary is dangerous as it could
destabilize the vehicle resulting in
an accident.
Do not start the engine or shake
the vehicle while it is jacked up:
Starting the engine or shaking the
vehicle while it is jacked up is
dangerous as it could cause the
8.
Turn the jack handle clockwise and
vehicle to fall off the jack resulting
raise the vehicle high enough so
in an accident.
that the spare tire can be installed.
Before removing the lug nuts, make
Never go under the vehicle while it
sure your Mazda is firmly in
is jacked up:
position and that it cannot slip or
Going under the vehicle while it is
move.
jacked up is dangerous as it could
result in death or serious injury if
the vehicle were to fall off the jack.
9.
Remove the lug nuts by turning
them counterclockwise; then
remove the wheel and center cap.
7-9
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст