Mazda CX-30 (2021 year). Manual in english — page 5
Before Driving
Driving Tips
WARNING
Hazardous Driving
Never stop the engine when going
▼ Hazardous Driving
down a hill:
Stopping the engine when going down
WARNING
a hill is dangerous. This causes the loss
of power steering and power brake
Be extremely careful if it is necessary
control, and may cause damage to the
to downshift on slippery surfaces:
drivetrain. Any loss of steering or
Downshifting into lower gear while
braking control could cause an
driving on slippery surfaces is
accident.
dangerous. The sudden change in tire
speed could cause the tires to skid.
This could lead to loss of vehicle
control and an accident.
Avoid sharp turns, excessive speed
and abrupt maneuvers when driving
this vehicle:
Sharp turns, excessive speed and
abrupt maneuvering of this vehicle are
dangerous as it could result in the
increased risk of loss of vehicle control,
vehicle roll-over, personal injury or
death.
This vehicle has a higher center of
gravity. Vehicles with a higher center of
gravity such as utility vehicles handle
differently than vehicles with a lower
center of gravity.
Utility vehicles are not designed for
cornering at high speeds any more
than low profile sports cars are
designed to perform satisfactorily
under off-road conditions.
In addition, utility vehicles have a
significantly higher rollover rate than
other types of vehicles.
In a rollover crash, an unbelted person
is significantly more likely to die than a
person wearing a seat belt.
3-50
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Driving Tips
When driving on ice or in water, snow,
Floor Mat
mud, sand, or similar hazards:
Be cautious and allow extra distance
▼ Floor Mat
for braking.
We recommend the use of Genuine
Avoid sudden braking and sudden
Mazda floor mats.
maneuvering.
Do not pump the brakes. Continue
WARNING
to press down on the brake pedal.
Refer to Antilock Brake System (ABS)
Make sure the floor mats are hooked
on page 4-75.
on the retention pins to prevent them
If you get stuck, select a lower gear
from bunching up under the foot
and accelerate slowly. Do not spin
pedals:
the front wheels.
Using a floor mat that is not secured is
For more traction in starting on
dangerous as it will interfere with the
slippery surfaces such as ice or
accelerator and brake pedal operation,
packed snow, use sand, rock salt,
which could result in an accident.
chains, carpeting, or other nonslip
material under the front wheels.
Do not install two floor mats, one on
top of the other, on the driver's side:
NOTE
Installing two floor mats, one on top of
Use snow chains only on the front
the other, on the driver's side is
wheels.
dangerous as the retention pins can
only keep one floor mat from sliding
forward.
Loose floor mat(s) will interfere with
the foot pedals and could result in an
accident.
If using an all-weather mat for winter
use always remove the original floor
mat.
When setting a floor mat, position the
floor mat so that its grommets are
inserted over the pointed end of the
retention posts.
3-51
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Driving Tips
Rocking the Vehicle
Winter Driving
▼ Rocking the Vehicle
▼ Winter Driving
Carry emergency gear, including tire
WARNING
chains, window scraper, flares, a small
shovel, jumper cables, and a small bag
Do not spin the wheels at more than
of sand or salt.
56 km/h (35 mph), and do not allow
Ask an Authorized Mazda Dealer to
anyone to stand behind a wheel when
check the following:
pushing the vehicle:
Have the proper ratio of antifreeze in
When the vehicle is stuck, spinning the
the radiator.
wheels at high speed is dangerous. The
Refer to Engine Coolant on page
spinning tire could overheat and
6-19.
explode. This could cause serious
Inspect the battery and its cables.
injuries.
Cold reduces battery capacity.
Use an engine oil appropriate for the
CAUTION
lowest ambient temperatures that
the vehicle will be driven in (page
Too much rocking may cause
6-17).
transmission failure, and tire damage.
Inspect the ignition system for
damage and loose connections.
If you must rock the vehicle to free it
Use washer fluid made with
from snow, sand or mud, depress the
antifreeze―but do not use engine
accelerator slightly and slowly move
coolant antifreeze for washer fluid
the shift lever/selector lever from 1 (D)
(page 6-21).
to R position.
NOTE
Remove snow before driving. Snow
left on the windshield is dangerous
as it could obstruct vision.
Do not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windshield.
Never use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
3-52
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Driving Tips
Drive slowly. Braking performance
NOTE
can be adversely affected if snow or
The tire pressure monitoring system
ice adheres to the brake
may not function correctly when using
components. If this situation occurs,
tires with steel wire reinforcement in
drive the vehicle slowly, releasing the
the sidewalls (page 4-214).
accelerator pedal and lightly applying
▼ Tire Chains
the brakes several times until the
brake performance returns to
Check local regulations before using
normal.
tire chains.
▼ Snow Tires
CAUTION
Use snow tires on all 4 wheels
¾ Chains may affect handling.
Do not go faster than 120 km/h (75
¾ Do not go faster than 50 km/h (30
mph) while driving with snow tires.
mph) or the chain manufacturer's
Inflate snow tires 30 kPa (0.3 kgf/cm2,
recommended limit, whichever is
4.3 psi) more than recommended on
lower.
the tire pressure label (driver's door
¾ Drive carefully and avoid bumps,
frame), but never more than the
holes, and sharp turns.
maximum cold-tire pressure shown on
¾ Avoid locked-wheel braking.
the tires.
¾ Do not use chains on a temporary
spare tire; it may result in damage to
The vehicle is originally equipped with
the vehicle and to the tire.
all season radials designed to be used
¾ Do not use chains on roads that are
all year around. In some extreme
free of snow or ice. The tires and
climates you may find it necessary to
chains could be damaged.
replace them with snow tires during
¾ Chains may scratch or chip
the winter months to further improve
aluminum wheels.
traction on snow and ice covered
roads.
NOTE
WARNING
The tire pressure monitoring system
may not function correctly when
Use only the same size and type tires
using tire chains.
(snow, radial, or non-radial) on all 4
Install the chains on the front tires only.
wheels:
Do not use chains on the rear tires.
Using tires different in size or type is
Please consult an Authorized Mazda
dangerous. Your vehicle's handling
Dealer.
could be greatly affected and result in
an accident.
CAUTION
Check local regulations before using
studded tires.
3-53
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Driving Tips
Installing the chains
Driving In Flooded Area
1.
If your vehicle is equipped with
wheel covers remove them,
▼ Driving In Flooded Area
otherwise the chain bands will
scratch them.
WARNING
2.
Secure the chains on the front tires
as tightly as possible.
Dry off brakes that have become wet
Always follow the chain
by driving slowly, releasing the
manufacturer's instructions.
accelerator pedal and lightly applying
3.
Retighten the chains after driving
the brakes several times until the
1/2―1 km (1/4―1/2 mile).
brake performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected.
CAUTION
Do not drive the vehicle on flooded
roads as it could cause short circuiting
of electrical/electronic parts, or engine
damage or stalling from water
absorption. If the vehicle has been
immersed in water, consult an
Authorized Mazda Dealer.
3-54
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Driving Tips
Overloading
Driving on Uneven Road
▼ Overloading
▼ Driving on Uneven Road
Your vehicle's suspension and
WARNING
underbody can be damaged if driven
on rough/uneven roads or over speed
Be careful not to overload your
bumps at excessive speeds. Use care
vehicle:
and reduce speed when traveling on
The gross axle weight rating (GAWR)
rough/uneven roads or over speed
and the gross vehicle weight rating
bumps.
(GVWR) of the vehicle are on the
Motor Vehicle Safety Standard Label
Use care not to damage the vehicle's
on the driver's door frame. Exceeding
underbody, bumpers or muffler(s)
these ratings can cause an accident or
when driving under the following
vehicle damage. You can estimate the
conditions:
weight of the load by weighing the
Ascending or descending a slope
items (or people) before putting them
with a sharp transition angle
in the vehicle.
Ascending or descending a driveway
or trailer ramp with a sharp transition
angle
This vehicle is equipped with low
profile tires allowing class-leading
performance and handling. As a result,
the sidewall of the tires are very thin
and the tires and wheels can be
damaged if driven through potholes or
on rough/uneven roads at excessive
speeds. Use care and reduce speed
when traveling on rough/uneven roads
or through potholes.
3-55
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Driving Tips
Turbocharger Information
(SKYACTIV-G 2.5T)
▼ Turbocharger Information
(SKYACTIV-G 2.5T)
CAUTION
¾ After driving at freeway speeds or up
a long hill, idle the engine at least 30
seconds before stopping it.
Otherwise, the turbocharger could
be damaged.
¾ Racing or over-revving the engine,
particularly after it's just been
started, can damage the
turbocharger.
¾ To protect the engine from damage,
the engine is designed so that it
cannot be raced just after starting it
in extremely cold weather.
The turbocharger greatly enhances
engine power. Its advanced design
provides improved operation and
requires minimum maintenance.
To get the most from it, observe the
following.
1. Change engine oil and filter
according to Scheduled
Maintenance.
Refer to Scheduled Maintenance
(U.S.A. and Puerto Rico) on page
6-4.
Refer to Scheduled Maintenance
(Canada) on page 6-6.
Refer to Scheduled Maintenance
(Mexico) on page 6-9.
2. Use only recommended engine oil
(page 6-17). Extra additives are
NOT recommended.
3-56
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Before Driving
Towing
Trailer Towing
Recreational Towing
▼ Trailer Towing
▼ Recreational Towing
Your Mazda is not designed for towing.
An example of "recreational towing" is
Never tow a trailer with your Mazda.
towing your vehicle behind a
motorhome.
The transmission is not designed for
towing this vehicle on all 4 wheels.
When doing recreational towing refer
to "Towing Description" (page 7-19)
and "Tiedown Hooks" (page 7-20)
and carefully follow the instructions.
3-57
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
4
Information concerning safe driving and stopping.
Start/Stop Engine
4-4
Rear Window Wiper and
Ignition Switch
4-4
Washer
4-54
Starting the Engine
4-5
Rear Window Defogger
4-55
Turning the Engine Off
4-10
Horn
4-56
Cylinder Deactivation
4-11
Hazard Warning Flasher
4-57
HomeLink Wireless Control
System*
4-57
Instrument Cluster and
Display
4-12
Instrument Cluster and
Brake
4-63
Display
4-12
Brake System
4-63
Instrument Cluster
4-12
AUTOHOLD
4-69
Active Driving Display*
4-28
Hill Launch Assist (HLA)
4-73
Manual Transmission
ABS/TCS/DSC/Off-Road
Operation
4-30
Traction Assist
4-75
Manual Transmission Shift
Antilock Brake System
Pattern
4-30
(ABS)
4-75
Traction Control System
(TCS)
4-76
Automatic Transmission
4-33
Dynamic Stability Control
Automatic Transmission
(DSC)
4-78
Controls
4-33
Off-Road Traction Assist*
4-79
Shift-Lock System
4-34
Transmission Ranges
4-35
Manual Shift Mode
4-36
Drive Selection
4-81
Direct Mode*
4-42
Drive Selection*
4-81
Driving Tips
4-43
i-ACTIV AWD
4-83
Switches and Controls
4-44
i-ACTIV AWD Operation*
4-83
Lighting Control
4-44
Turn and Lane-Change
Power Steering
4-85
Signals
4-49
Power Steering
4-85
Windshield Wipers and
Washer
4-50
*Some models.
4-1
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
i-ACTIVSENSE
4-86
Smart Brake Support [Rear] (SBS-
i-ACTIVSENSE*
4-86
R)*
4-157
Adaptive Front Lighting System
Smart Brake Support [Rear
(AFS)*
4-90
Crossing] (SBS-RC)*
4-161
High Beam Control System
360° View Monitor*
4-165
(HBC)*
4-91
Forward Sensing Camera
Lane Departure Warning System
(FSC)*
4-198
(LDWS)*
4-93
Front Radar Sensor*
4-202
Blind Spot Monitoring (BSM)*
Front Side Radar Sensor*
4-204
. . . . . . . . . . .. 4-96
Rear Side Radar Sensor*
4-205
Traffic Sign Recognition System
Rear/Rear corner/Rear Side
(TSR)*
4-101
Ultrasonic Sensor*
4-207
Distance & Speed Alert (DSA)*
Front Camera/Side Cameras/
. . . . . . . . . . 4-107
Rear Camera*
4-207
Driver Attention Alert (DAA)*
Driver Monitoring Camera*
. . . . . . . . . . 4-108
. . . . . . . . . . 4-208
Driver Monitoring (DM)*
4-110
Front Cross Traffic Alert
Cruise Control
4-209
(FCTA)*
4-112
Cruise Control*
4-209
Rear Cross Traffic Alert (RCTA)*
. . . . . . . . . . 4-115
Tire Pressure Monitoring System
Mazda Radar Cruise Control
(TPMS)
4-213
(MRCC) (Manual
Tire Pressure Monitoring System
Transmission)*
4-119
(TPMS)
4-213
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) (Automatic
Rear View Monitor
4-217
Transmission)*
4-127
Rear View Monitor*
4-217
Traffic Jam Assist (TJA)*
4-137
Lane-keep Assist System (LAS)*
Parking Sensor System
4-232
. . . . . . . . . . 4-151
Parking Sensor System*
4-232
Smart Brake Support (SBS)*
. . . . . . . . . . 4-155
4-2
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
Off
Ignition Switch
The power supply to electrical devices
▼ Push Button Start Positions
turns off and the indicator light
(amber) also turns off.
The system operates only when the key
is within operational range.
WARNING
Each time the push button start is
pressed, the ignition switches in the
order of off, ACC, and ON. Pressing
Before leaving the driver's seat,
the push button start again from ON
always switch the ignition off, set the
switches the ignition off.
parking brake, and make sure the
selector lever is in P (automatic
transmission) position or in 1st gear
or R (manual transmission):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transmission)
position or to 1st gear or R (manual
transmission) is dangerous.
Unexpected vehicle movement could
occur which could result in an
1. Indicator light
accident.
2. Push button start
In addition, if your intention is to leave
the vehicle for even a short period, it is
NOTE
important to switch the ignition off, as
The engine starts by pressing the
leaving it in another position will
push button start while depressing
disable some of the vehicle's security
the clutch pedal (manual
systems and run the battery down.
transmission) or the brake pedal
ACC (Accessory)
(automatic transmission). To switch
the ignition position, press the push
Some electrical accessories will
button start without depressing the
operate and the indicator light (amber)
pedal.
illuminates.
Do not leave the ignition switched
NOTE
ON while the engine is not running.
The keyless entry system does not
Doing so could result in the battery
function while the push button start
going dead. If the ignition is left in
has been pressed to ACC, and the
ACC (For automatic transmission,
doors will not lock/unlock even if they
the selector lever is in the P position,
have been locked manually.
and the ignition is in ACC), the
ignition switches off automatically
after about 25 minutes.
4-4
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
ON
Starting the Engine
This is the normal running position
after the engine is started. The
▼ Starting the Engine
indicator light (amber) turns off. (The
indicator light (amber) illuminates
WARNING
when the ignition is switched ON and
the engine is not running.)
Radio waves from the key may affect
Some indicator lights/warning lights
medical devices such as pacemakers:
should be inspected before the engine
Before using the key near people who
is started.
use medical devices, ask the medical
Refer to Warning/Indicator Lights on
device manufacturer or your physician
page 4-22.
if radio waves from the key will affect
Refer to Indication/Indicator Lights on
the device.
page 4-24.
NOTE
NOTE
When the push button start is pressed
The key must be carried because the
to ON, the sound of the fuel pump
key carries an immobilizer chip that
motor operating near the fuel tank can
must communicate with the engine
be heard. This does not indicate an
controls at short range.
abnormality.
The engine can be started when the
push button start is pressed from off,
ACC, or ON.
The push button start system
functions (function which can start
the engine by only carrying the key)
can be deactivated to prevent any
possible adverse effect on a user
wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable to
start the engine by carrying the key.
Consult an Authorized Mazda Dealer
for details. If the push button start
system functions have been
deactivated, you can start the engine
by following the procedure indicated
when the key battery goes dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-8.
4-5
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
After starting a cold engine, the
6.
Make sure that the KEY indicator
engine speed increases and a
light (green) in the instrument
whining sound from the engine
cluster and push button start
compartment can be heard.
indicator light (green) turns on.
This is for improved exhaust gas
purification and does not indicate
any parts defect.
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
1.
Make sure you are carrying the key.
1. Indicator light
2.
Occupants should fasten their seat
2. Push button start
belts.
NOTE
3.
Make sure the parking brake is on.
4.
Continue to depress the brake
If the push button start indicator
pedal firmly until the engine has
light (green) flashes, make sure
completely started.
that the key is being carried.
5.
(Manual transmission)
If the push button start indicator
Continue to depress the clutch
light (green) flashes with the key
pedal firmly until the engine has
being carried, touch the key to
completely started.
the push button start and start
(Automatic transmission)
the engine.
Put the vehicle in park (P). If you
Refer to Engine Start Function
must restart the engine while the
When Key Battery is Dead on
vehicle is moving, shift into neutral
page 4-8.
(N).
NOTE
CAUTION
(Manual transmission)
If the KEY warning indication (red)
The starter will not operate if the
is displayed, or the push button
clutch pedal is not depressed
start indicator light (amber) flashes,
sufficiently.
this could indicate a problem with
(Automatic transmission)
the engine starting system. This may
The starter will not operate if the
prevent the engine from starting or
selector lever is not in P or N
from switching the ignition to ACC
position and the brake pedal is
or ON.
not depressed sufficiently.
Refer to KEY Warning Indication/
Warning Light (Red) on page
7-28.
4-6
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
Have your vehicle inspected at an
When the engine is force-started,
Authorized Mazda Dealer as soon
the KEY warning indication (red)
as possible.
remains displayed and the push
button start indicator light
NOTE
(amber) remains flashing.
(Automatic transmission)
Under the following conditions,
When the selector lever is in the
the KEY warning indication (red)
neutral (N) position, the push
is displayed after the push button
button start indicator light (green)
start is pressed. This informs the
does not turn on.
driver that the push button start
7.
Press the push button start after the
will not switch to ACC, even if it
push button start indicator light
is pressed from off (page 7-28).
(green) turns on.
The key battery is dead.
NOTE
The key is out of operational
range.
After starting the engine, the push
The key is placed in areas where
button start indicator light
it is difficult for the system to
(amber) turns off and the ignition
detect the signal (page 3-7).
switches to the ON position.
A key from another
After pressing the push button
manufacturer similar to the key
start and before the engine starts,
is in the operational range.
the operation sound of the fuel
(Forced engine starting method)
pump motor from near the fuel
If the KEY warning indication
tank can be heard, however, this
(red) is displayed, or the push
does not indicate a malfunction.
button start indicator light
8.
After starting the engine, let it idle
(amber) flashes, this could
for about 10 seconds.
indicate that the engine may not
NOTE
start using the usual starting
method (page 7-28). Have your
Do not use high engine speeds
vehicle inspected at an
until reaching the operating
Authorized Mazda Dealer as
temperature.
soon as possible. If this occurs,
Whether the engine is cold or
the engine can be force-started.
warm, it should be started
Press and hold the push button
without the use of the
start until the engine starts. Other
accelerator.
procedures necessary for starting
If the engine does not start the
the engine, such as having the key
first time, refer to Starting a
in the cabin, and depressing the
Flooded Engine under Emergency
clutch pedal (manual
Starting. If the engine still does
transmission) or the brake pedal
not start, have your vehicle
(automatic transmission) are
inspected by an Authorized
required.
Mazda Dealer (page 7-16).
4-7
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
▼ Engine Start Function When Key
If the engine cannot be started due to
Battery is Dead
a dead key battery, the engine can be
started using the following procedure:
1. Continue to depress the brake
CAUTION
pedal firmly until the engine has
completely started.
When starting the engine by holding
2.
(Manual transmission)
the transmitter over the push button
Continue to depress the clutch
start due to a dead key battery or a
pedal firmly until the engine has
malfunctioning key, be careful not to
completely started.
allow the following, otherwise the
(Automatic transmission)
signal from the key will not be received
Put the vehicle in park (P). If you
correctly and the engine may not start.
must restart the engine while the
¾ Metal parts of other keys or metal
vehicle is moving, shift into neutral
objects touch the key.
(N).
3. Make sure that the push button
start indication light (green) flashes.
4. Align the center area of the
emblem on the transmitter with the
center area of the push button start
while the push button start
¾ Spare keys or keys for other vehicles
indicator light (green) flashes.
equipped with an immobilizer
system touch or come near the key.
¾ Devices for electronic purchases, or
security passage touch or come near
the key.
1. Indicator light
2. Push button start
3. Transmitter
4. Emblem
5. Make sure that the push button
start indicator light (green) turns
on.
6. Press the push button start to start
the engine.
4-8
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
NOTE
▼ Emergency Operation for Starting
the Engine
The engine cannot be started
unless the clutch pedal is fully
If the KEY warning indication (red) is
depressed (manual transmission)
displayed, or the push button start
or the brake pedal is fully
indicator light (amber) flashes, this
depressed (automatic
could indicate that the engine may not
transmission).
start using the usual starting method.
If there is a malfunction with the
Have your vehicle inspected at an
push button start function, the
Authorized Mazda Dealer as soon as
push button start indicator light
possible. If this occurs, the engine can
(amber) flashes. In this case, the
be force-started. Press and hold the
engine may start, however, have
push button start until the engine
the vehicle checked at an
starts. Other procedures necessary for
Authorized Mazda Dealer as
starting the engine such as having the
soon as possible.
key in the cabin, and depressing the
If the push button start indicator
clutch pedal (manual transmission) or
light (green) does not illuminate,
the brake pedal (automatic
perform the operation from the
transmission) are required.
beginning again. If it does not
illuminate, have the vehicle
checked at an Authorized Mazda
Dealer.
To switch the ignition position
without starting the engine,
perform the following operations
after the push button start
indicator light (green) turns on.
1. Release the clutch pedal
(manual transmission) or
brake pedal (automatic
transmission).
2. Press the push button start to
switch the ignition position.
The ignition switches in the
order of ACC, ON, and off
each time the push button
start is pressed. To switch the
ignition position again,
perform the operation from
the beginning.
4-9
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
Turning the Engine Off
CAUTION
▼ Turning the Engine Off
¾ When leaving the vehicle, make sure
the push button start is off.
WARNING
NOTE
(SKYACTIV-G)
Do not stop the engine while the
vehicle is moving:
The cooling fan in the engine
Stopping the engine while the vehicle
compartment could turn on for a few
is moving for any reason other than in
minutes after the ignition is switched
an emergency is dangerous. Stopping
from ON to OFF, whether or not the
the engine while the vehicle is moving
A/C is on or off, to cool the engine
will result in reduced braking ability
compartment quickly.
due to the loss of power braking,
If the system detects that the
which could cause an accident and
remaining battery power of the key is
serious injury.
low when the ignition is switched
from ON to ACC or OFF, the
1. Stop the vehicle completely.
following is indicated.
2.
(Manual transmission)
Replace with a new battery before
Shift into neutral and set the
the key becomes unusable.
parking brake.
Refer to Key Battery Replacement on
(Automatic transmission)
page 6-29.
Shift the selector lever to the P
A message is indicated in the display
position and set the parking brake.
of the instrument cluster.
3. Press the push button start to turn
Refer to KEY Warning Indication/
off the engine. The ignition position
Warning Light (Red) on page 7-28.
is off.
(Automatic transmission)
If the engine is turned off while the
selector lever is in a position other
than P, the ignition switches to ACC.
▼ Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number
of times while the engine is running or
the vehicle is being driven will turn the
engine off immediately. The ignition
switches to ACC.
4-10
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Start/Stop Engine
Cylinder Deactivation
▼ Cylinder Deactivation
The cylinder deactivation is a function
designed to reduce fuel consumption
and improve fuel economy by
deactivating 2 out of the 4 cylinders
while driving. The function constantly
determines which is better for driving;
4 cylinders or 2 cylinders, regardless of
the driver's operations, and it performs
the switching automatically.
When the cylinder deactivation
function does not operate
The cylinder deactivation function
does not operate under the following
conditions.
The selector lever is in the P, N, or R
position (automatic transmission), or
1st gear (manual transmission).
The engine oil temperature or engine
coolant temperature is low.
After disconnecting the battery
terminals for some reason, such as
for battery replacement.
4-11
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
Instrument Cluster and
Instrument Cluster
Display
▼ Instrument Cluster
▼ Instrument Cluster and Display
ᶃ Tachometer
page 4-13
ᶄ Multi-information Display
ᶃ Instrument Cluster
page 4-12
. . . . . . . . . . page 4-14
ᶄ Active Driving Display
page 4-28
ᶅ Engine Coolant Temperature
Gauge
page 4-16
ᶆ Fuel Gauge
page 4-17
ᶇ Dashboard Illumination
Switch
page 4-18
ᶈ Speedometer
page 4-12
ᶉ TRIP Switch
page 4-16
▼ Speedometer
The speedometer indicates the speed
of the vehicle.
4-12
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
▼ Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).
CAUTION
Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.
1. STRIPED ZONE*1
2. RED ZONE*1
*1
The range varies depending on the type of
gauge.
NOTE
When the tachometer needle enters
the STRIPED ZONE, this indicates to
the driver that the gears should be
shifted before entering the RED ZONE.
4-13
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
▼ Multi-information Display
1. Multi-information Display
2. INFO switch
The multi-information display indicates the following information.
Speedometer
Odometer
Trip meter
Outside temperature
Distance-to-empty
Average fuel economy
Current fuel economy
i-ACTIVSENSE Display
Compass Display
Door-Ajar/Liftgate-Ajar Warning Indication*1
Message Display
*1
Displayed when opening door/liftgate.
4-14
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
The screen content changes each time the INFO switch is pressed.
1. Basic display
2. Drive information display
3. i-ACTIVSENSE display
4. Message display*1
*1
Displayed only when a warning occurs.
The type of display for the fuel economy and the maximum driving distance can be
changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
4-15
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
▼ Odometer, Trip Meter and Trip
For instance, trip meter A can record
Meter Selector
the distance from the point of origin,
and trip meter B can record the
You can switch between the odometer
distance from where the fuel tank is
and trip meter display using the TRIP
filled.
switch.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
The trip meter can be reset by pressing
the TRIP switch for 1.5 seconds or
more while the trip meter is displayed.
NOTE
Only the trip meters record tenths of
kilometers (miles).
▼ Engine Coolant Temperature
Gauge
Displays the engine coolant
temperature. The blue range of the
gauge indicates that the engine coolant
temperature is low, and the red range
of the gauge indicates that the engine
coolant temperature is high and
overheating.
1.
TRIP switch
2.
Odometer display
3.
Trip meter A display
4.
Trip meter B display
Odometer
The odometer records the total
distance the vehicle has been driven.
Trip meter
The driving distance for a specified
interval is indicated. Two types (TRIP A,
TRIP B) of interval distance can be
measured.
4-16
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
▼ Fuel Gauge
CAUTION
The fuel gauge shows approximately
When the engine coolant temperature
how much fuel is remaining in the tank
gauge needle is in the red range, the
when the ignition is switched ON. We
engine coolant temperature is
recommend keeping the tank over 1/4
extremely high. Drive slowly to reduce
full.
engine load. If the engine coolant
temperature gauge needle is in the red
range, there is the possibility of
overheating. Park the vehicle in a safe
place immediately and take
appropriate measures.
Refer to Overheating on page 7-17.
NOTE
If the engine or engine coolant
temperature is high or low, the
engine output may be restricted to
protect the engine.
1. Full
2.
1/4 Full
3. Empty
If the low fuel warning light illuminates
or the fuel level is very low, refuel as
soon as possible.
If inconsistency in engine performance
or stalling occurs due to low fuel level
conditions, refuel the vehicle as soon
as possible and add at least 10 L (2.7
US gal, 2.2 Imp gal) of fuel.
Refer to Low Fuel Warning Indication/
Warning Light on page 7-30.
4-17
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
NOTE
The brightness increases by pressing
the + switch.
After refueling, it may require some
The brightness decreases by pressing
time for the indicator to stabilize. In
the - switch. If you press the - switch
addition, the indicator may deviate
while the instrument cluster is at
while driving on a slope or curve
maximum dimness, a sound is
since the fuel moves in the tank.
activated to notify you that the
The direction of the arrow (
)
current dimmer setting is at
indicates that the fuel-filler lid is on
maximum dimness.
the left side of the vehicle.
▼ Dashboard Illumination
(Without auto-light control)
When the lights are turned on with the
ignition switched ON, the brightness of
the dashboard illumination is dimmed.
(With auto-light control)
When the lights are turned on with the
ignition switched ON, the brightness of
the dashboard illumination is dimmed.
However, when the light sensor
detects that the surrounding area is
1. Bright
bright such as when the lights are
2. Dim
turned on in the daytime, the
dashboard illumination does not dim.
Function for canceling illumination
dimmer
NOTE
The illumination dimmer can be
(With auto-light control)
canceled by pressing the + switch
When the ignition is switched ON in
while the instrument cluster is at
the early evening or at dusk, the
maximum dimness and while the
dashboard illumination is dimmed
ignition is switched ON. If you press
for several seconds until the light
the + switch again while the
sensor detects the brightness of the
illumination dimmer is canceled, a
surrounding area, however, the
sound is activated to notify you that it
dimming may cancel after the
is canceled. If the instrument cluster's
brightness is detected.
visibility is reduced due to glare from
When the lights are turned on, the
surrounding brightness, cancel the
lights-on indicator light in the
illumination dimmer.
instrument cluster turns on.
Refer to Headlights on page 4-44.
NOTE
The brightness of the instrument panel
When the illumination dimmer is
and dashboard illuminations can be
canceled, the instrument cluster
adjusted by pressing the dashboard
cannot be dimmed even if the lights
illumination switch while the
are turned on.
dashboard illumination is dimmed.
4-18
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
When the illumination dimmer is
▼ Distance-to-empty
canceled, the screen in the center
This displays the approximate distance
display switches to constant display
you can travel on the remaining fuel
of the daytime screen.
based on the fuel economy.
▼ Outside Temperature Display
The distance-to-empty will be
calculated and displayed every second.
When the ignition is switched ON, the
outside temperature is displayed.
NOTE
NOTE
Even though the distance-to-empty
display may indicate a sufficient
Under the following conditions, the
amount of remaining driving distance
outside temperature display may
before refueling is required, refuel as
differ from the actual outside
soon as possible if the fuel level is
temperature depending on the
very low or the low fuel warning light
surroundings and vehicle conditions:
illuminates.
Significantly cold or hot
The display will not change unless
temperatures.
you add more than approximately 9
Sudden changes in outside
L (2.3 US gal, 1.9 Imp gal) of fuel.
temperature.
The distance-to-empty is the
The vehicle is parked.
approximate remaining distance the
The vehicle is driven at low speeds.
vehicle can be driven until all the
graduation marks in the fuel gauge
Changing the Temperature Unit of the
indicating the remaining fuel supply
Outside Temperature Display
disappear.
The outside temperature unit can be
If there is no past fuel economy
information such as after first
switched between Celsius and
Fahrenheit.
purchasing your vehicle or the
information is deleted when the
Settings can be changed by operating
the center display screen.
battery cables are disconnected, the
actual distance-to empty/range may
Refer to the Settings section in the
Mazda Connect Owner's Manual.
differ from the amount indicated.
4-19
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
▼ Average Fuel Economy
NOTE
The average fuel economy is calculated
Indicates the 0 position when the
every 30 seconds from the total
vehicle speed is about 5 km/h (3
traveled distance on the trip meter and
mph) or slower.
the total fuel consumption, and the
The red arrow on the scale indicates
average fuel economy for either drive
the average fuel economy.
information display is displayed.
▼ i-ACTIVSENSE Display*
The average fuel economy is also
displayed by a red arrow in the
Displays the system status.
instantaneous fuel economy display.
Refer to Lane Departure Warning
The average fuel economy and trip
System (LDWS) on page 4-95.
meters can be reset by pressing the
Refer to Blind Spot Monitoring
INFO switch for 1.5 seconds or more
(BSM) on page 4-99.
while in each mode. After the data is
Refer to Traffic Sign Recognition
cleared, the fuel consumption is
System (TSR) on page 4-103.
recalculated and the - - - L/100 km
Refer to Distance & Speed Alert
(- - - mpg) for the 30 seconds prior to
(DSA) on page 4-108.
it being displayed is indicated.
Refer to Driver Attention Alert (DAA)
▼ Current Fuel Economy
on page 4-110.
Refer to Driver Monitoring (DM) on
This displays the current fuel economy
page 4-111.
by calculating the amount of fuel
Refer to Front Cross Traffic Alert
consumption and the distance
(FCTA) on page 4-112.
traveled.
Refer to Mazda Radar Cruise Control
(MRCC) on page 4-121.
Refer to Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function) on page
4-130.
Refer to Traffic Jam Assist (TJA) on
page 4-141.
Refer to Lane-keep Assist System
(LAS) on page 4-153.
Refer to Smart Brake Support (SBS)
on page 4-156.
4-20
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
Refer to Smart Brake Support [Rear]
▼ Message Display
(SBS-R) on page 4-160.
A message such as the system
Refer to Smart Brake Support [Rear
operation status, a malfunction, or an
Crossing] (SBS-RC) on page 4-164.
abnormality is indicated.
Refer to Cruise Control on page
4-210.
Warning/indicator light in instrument
cluster turns on/flashes or symbol is
▼ Compass Display
indicated on display at same time as
The direction the vehicle is moving is
message
displayed in one of eight directions
Check the information regarding the
while the vehicle is being driven.
warning/indicator light or indicated
symbol.
Refer to If a Warning Indication/
Warning Lights on page 4-22.
Refer to If a Indication/Indicator Lights
on page 4-24.
Message only is indicated on display
Follow the instructions indicated on
the display. For the display content,
refer to the next page.
Refer to If a Message Indicated on
Display
Direction
Multi-information Display on page
N
North
7-34.
S
South
▼ Warning/Indicator Lights
E
East
Instrument Cluster varies depending
W
West
on model and specifications.
NE
Northeast
NW
Northwest
SE
Southeast
SW
Southwest
1. Instrument Cluster
2. Front Center of Headliner
Warning lights will appear in any of the
highlighted areas
4-21
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
▼ Warning Indication/Warning Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal
Warning
Refer to
Brake System Warning Indication/Warning Light*1
7-22
Electronic
Brake Force
Distribution
System Warn-
ABS Warning Indication/Warning Light*1
ing
7-23
ABS warning
7-25
Charging System Warning Indication/Warning Light*1
7-23
Engine Oil Warning Indication/Warning Light*1
7-23
High Engine Coolant Temperature Warning Indication
7-24
Power Steering Malfunction Indication/Indicator Light*1
7-24
Master Warning Indication
7-25
Brake Control System Warning Indication/Warning Light*1
7-25
Brake Override Warning Indication
7-26
Check Engine Indication/Light*1
7-26
*Automatic Transmission Warning Indication/Warning Light
*1
7-26
*AWD Warning Indication/Warning Light*1
7-27
4-22
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
Signal
Warning
Refer to
Air Bag/Front Seat Belt Pretensioner System Warning Indication/
7-27
Warning Light*1
Flashing
Tire Pressure Monitoring System (TPMS) Warning Indication/Warning
7-28
Light*1
Turns on
7-32
KEY Warning Indication/Warning Light*1
7-28
(Red)
*High Beam Control System (HBC) Warning Indication/Warning
7-29
Light*1
(Amber)
i-ACTIVSENSE Warning Indication/Warning Light*1
7-29
Exterior Light Warning Indication/Warning Light*1
7-29
Low Fuel Warning Indication/Warning Light
7-30
Check Fuel Cap Warning Indication/Warning Light*1
7-30
Engine Oil Level Warning Indication/Warning Light*1
7-30
Seat Belt Warning Indication/Warning Light (Front seat)
7-31
Seat Belt Warning Light (Rear seat)
7-31
(Red)
*Low Washer Fluid Level Warning Indication/Warning Light
7-31
Door-Ajar Warning Indication
7-32
Liftgate-Ajar Warning Indication
7-32
*Some models.
4-23
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
Signal
Warning
Refer to
Door-Ajar Warning Light
7-32
*1
The light turns on when the ignition is switched on for an operation check, and turns off a few
seconds later or when the engine is started. If the light does not turn on or remains turned on, have
the vehicle inspected at an Authorized Mazda Dealer.
▼ Indication/Indicator Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal
Indicator
Refer to
Seat Belt Indicator Light (Rear seat)
2-25
(Green)
*Front Passenger Air Bag Deactivation Indicator Light
2-67
Immobilizer
System
3-46
Theft-Deterrent
Security Indicator Light
System
3-47
Malfunction
7-29
KEY Indicator Light
4-5
(Green)
Wrench Indication/Indicator Light*1
4-27
*Shift Position Indication
4-36
Lights-On Indicator Light
4-44
4-24
*Some models.
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
When Driving
Instrument Cluster and Display
Signal
Indicator
Refer to
Headlight
High-Low
Beam
Headlight High-Beam Indicator Light
4-47
Flashing the
Headlights
4-47
Turn and
Lane-Change
Signals
Turn Signal/Hazard Warning Indicator Lights
4-49
Hazard Warn-
ing Flasher
4-57
Electric Parking Brake (EPB) Indication/Indicator Light*1*2
7-25
AUTOHOLD Active Indicator Light*1
4-71
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
4-136
Stop & Go function) indicator Light
*Traffic Jam Assist (TJA) indicator Light
4-150
Traction Con-
trol System
(TCS)
4-76
Dynamic Sta-
TCS/DSC Indication/Indicator Light*1
bility Control
(DSC)
4-78
Turns on
7-27
TCS OFF Indicator Light (FWD) *1
4-77
Off-Road Traction Assist Indicator Light (AWD) *1
4-79
*Select Mode Indicator Light
4-82
*Some models.
4-25
CX-30_8JP5-EA-20K_Edition1_new
2020-7-22 15:50:09
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст