Mazda Protege 5. Manual — part 305
ON-BOARD DIAGNOSTIC [AUDIO]
09–02B–14
DIAGNOSTIC ASSIST FUNCTION
A3U090266900W26
Structural View
Switch location
LCD inspection
1. With audio on, first press the POWER button and hold it, then press the SEEK button (upper) for
approximately 1 second.
2. Inspect the LCD according to the following table:
3. Turn the audio off or the ignition switch to the LOCK position to stop the diagnostic assist function.
Z3U0920W004
1
FM1/2 button
2
AM button
3
CD button
4
MD/TAPE button
5
CLOCK button
6
SEEK button (upper)
7
SEEK button (lower)
8
POWER/VOL button
9
Preset button “1”
10
Preset button “2”
11
Preset button “3”
12
Preset button “4”
13
Preset button “5”
14
Preset button “6”
15
AUDIO CONT/TURN button
16
SCAN button
17
AUTO-M button
18
LOAD button (CD changer)
19
EJECT button (CD player and CD changer)
Inspection
Display
Action
Start LCD inspection mode.
Characters displayed in LCD
are not truncated or faint.
LCD is okay.
Other than above.
Replace base unit.
1712-1U-01G(09-02B).fm 14 ページ 2001年6月29日 金曜日 午前10時27分
ON-BOARD DIAGNOSTIC [AUDIO]
09–02B–15
09–02B
Button inspection
1. With audio on, first press the POWER button and hold it, then press the CLOCK button for approximately 1
second.
2. Inspect the button according to the following table:
Note
•
The button inspection mode is designed for base unit button. The following lower module button cannot be
inspected in this mode. (A buzz will not sound.)
— Cassete deck: DOLBY button, EJECT button
— MD player: DISP button, EJECT button
3. Turn the audio off or the ignition switch to the LOCK position to stop the diagnostic assist function.
Speaker inspection
1. With audio on, first press the POWER button and hold it, then press the AUTO-M button for approximately 1
second.
2. Inspect the speaker according to the following table:
3. Turn the audio off or the ignition switch to the LOCK position to stop the diagnostic assist function.
Radio reception condition inspection
1. With audio on and at radio mode, first press the POWER button and hold it, then press the preset button “2” for
approximately 1 second.
2. Inspect the radio reception condition according to the following table:
3. Turn the audio off or the ignition switch to the LOCK position to stop the diagnostic assist function.
End Of Sie
Inspection
Display
Action
•
Start button inspection
mode.
•
Press the all buttons.
—
Buzzer sounds.
Button is okay.
Buzzer does not sound.
Replace base unit.
Inspection
Display
Action
•
Start speaker inspection
mode.
•
Does each speaker
output sound in the
following order?
1. Left front door speaker
2. Right front door
speaker
3. Right rear package
speaker (4SD) or rear
door speaker (5HB)
4. Left rear package
speaker (4SD) or rear
door speaker (5HB)
—
Yes
Speakers and wiring harness between base
unit and speakers are okay.
No
Inspect the following parts.
•
Malfunctioning speaker
•
Wiring harness between base unit and
malfunctioning speaker
Inspection
Display
Action
Start radio reception
condition inspection mode.
Antenna, antenna feeder, and base unit are okay.
Change frequency (channel) and inspect again.
Inspect antenna and antenna feeder.
•
If either one of them is not okay, replace malfunctioning
part.
•
If both are okay, replace base unit.
1712-1U-01G(09-02B).fm 15 ページ 2001年6月29日 金曜日 午前10時27分
SYMPTOM TROUBLESHOOTING
09–03–1
09–03
09–03
SYMPTOM TROUBLESHOOTING
KEYLESS ENTRY SYSTEM
WIRING DIAGRAM . . . . . . . . . . . . . . . . 09–03–1
FOREWORD . . . . . . . . . . . . . . . . . . . . . . 09–03–1
KEYLESS ENTRY SYSTEM
CHECK SHEET . . . . . . . . . . . . . . . . . . . 09–03–2
KEYLESS ENTRY SYSTEM
PREINSPECTION . . . . . . . . . . . . . . . . . 09–03–3
TROUBLESHOOTING INDEX . . . . . . . . . 09–03–3
NO.1 ONE OR MORE ON-BOARD DIAGNOSTIC
FUNCTIONS INOPERATIVE . . . . . . . . . 09–03–4
NO.2 ALL ON-BOARD DIAGNOSTIC
FUNCTIONS INOPERATIVE . . . . . . . . . 09–03–6
NO.3 TRANSMITTER ID CODE CANNOT
BE REPROGRAMMED . . . . . . . . . . . . . 09–03–7
End of Toc
KEYLESS ENTRY SYSTEM WIRING DIAGRAM
A3U090369000W01
End Of Sie
FOREWORD
A3U090369000W02
•
Go to symptom troubleshooting after identifying
the specific malfunction by performing a keyless
entry system preliminary inspection.
End Of Sie
A3U0903W001
ZLU0903W001
1712-1U-01G(09-03).fm 1 ページ 2001年6月29日 金曜日 午前10時28分
SYMPTOM TROUBLESHOOTING
09–03–2
KEYLESS ENTRY SYSTEM CHECK SHEET
A3U090369000W03
Note
•
Use the sheet below as a customer interview sheet when accepting a vehicle for service.
•
If the symptom is “Power door lock system does not operate with transmitter at all”, find out how the
customer uses the keyless entry system by following the check sheet below.
End Of Sie
Z3U0903W003
1712-1U-01G(09-03).fm 2 ページ 2001年6月29日 金曜日 午前10時28分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст