Mazda Protege 5. Manual — part 345
WIPER/WASHER SYSTEM
09–19–6
WINDSHIELD WIPER MOTOR REMOVAL/INSTALLATION
A3U091967340W01
1. Disconnect the negative battery cable.
2. Remove the windshield wiper arm and blade. (See 09–19–5 WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION.)
3. Remove the cowl grille. (See 09–16–1 COWL GRILLE REMOVAL/INSTALLATION.)
4. Pry off the connection between the windshield wiper motor and windshield wiper link.
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
7. Adjust the windshield wiper arm and blade. (See
09–19–5 WINDSHIELD WIPER ARM AND
BLADE ADJUSTMENT.)
End Of Sie
WINDSHIELD WIPER MOTOR INSPECTION
A3U091967340W02
1. Disconnect the windshield wiper motor connector.
2. Connect battery positive voltage and inspect the
operation of the windshield wiper motor as
indicated below.
3. Disconnect battery positive voltage from terminal
C of the motor while the wipers are operating.
4. Verify that the wipers do not stop in the park
position.
5. Short between terminal B and C of the motor and
connect battery positive voltage to terminal D of
the motor.
6. Verify that the wipers operate at low speed again, then stop in the park position.
•
If not as specified, replace the windshield wiper motor.
End Of Sie
1
Connector
2
Bolt
3
Windshield wiper motor
X3U919WA0
Terminal
Operation
A
High
C
Low
Z3U0919W001
1712-1U-01G(09-19).fm 6 ページ 2001年6月29日 金曜日 午前10時37分
WIPER/WASHER SYSTEM
09–19–7
09–19
WASHER TANK REMOVAL/INSTALLATION
A3U091967480W01
1. Disconnect the negative battery cable.
2. Partially peel off the right side mud guard.
3. Partially remove the right side front bumper (if equipped with washer fluid-level sensor). (See 09–10–5 FRONT
BUMPER REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
.
End Of Sie
WINDSHIELD WASHER MOTOR REMOVAL/INSTALLATION
A3U091976670W01
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See 09–19–7 WASHER TANK REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
A3U0919W112
1
Bolt
2
Connector
3
Windshield washer hose
4
Rear washer hose
5
Washer tank
1
Windshield washer motor
2
Grommet
X3U919WA8
1712-1U-01G(09-19).fm 7 ページ 2001年6月29日 金曜日 午前10時37分
WIPER/WASHER SYSTEM
09–19–8
WINDSHIELD WASHER MOTOR INSPECTION
A3U091976670W02
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See 09–19–7 WASHER TANK REMOVAL/INSTALLATION.)
3. Connect battery positive voltage to the terminal B and ground to the terminal A of the motor.
4. Verify that the windshield washer motor operates.
•
If the motor does not operate, replace the windshield washer motor.
End Of Sie
WASHER FLUID-LEVEL SENSOR REMOVAL/INSTALLATION
A3U091967488W01
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See 09–19–7 WASHER TANK REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
WASHER FLUID-LEVEL SENSOR INSPECTION
A3U091967488W02
1. Disconnect the negative battery cable.
2. Remove the washer tank. (See 09–19–7 WASHER TANK REMOVAL/INSTALLATION.)
3. Inspect for continuity between the washer fluid-level sensor terminals using an ohmmeter.
•
If not as specified, replace the washer fluid-level sensor.
End Of Sie
Y3U919WA3
1
Washer fluid-level sensor
2
Grommet
X3U919WB0
Y3U919WA4
X3U919WB1
1712-1U-01G(09-19).fm 8 ページ 2001年6月29日 金曜日 午前10時37分
WIPER/WASHER SYSTEM
09–19–9
09–19
WIPER AND WASHER SWITCH REMOVAL/INSTALLATION
A3U091966122W01
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09–17–5 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
WIPER AND WASHER SWITCH INSPECTION
A3U091966122W02
Windshield Wiper and Washer
1. Disconnect the negative battery cable.
2. Remove the wiper and washer switch. (See 09–19–9 WIPER AND WASHER SWITCH REMOVAL/
INSTALLATION.)
3. Inspect for continuity between the wiper and
washer switch terminals using an ohmmeter.
•
If not as specified, replace the wiper and
washer switch.
1
Connector
2
Screw
3
Wiper and washer switch
X3U919WB7
Y3U919WA5
X3U919WB8
1712-1U-01G(09-19).fm 9 ページ 2001年6月29日 金曜日 午前10時37分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст