Mazda Protege 5. Manual — part 339
LIGHTING SYSTEMS
09–18–9
09–18
FRONT FOG LIGHT ADJUSTMENT
A3U091851680W02
1. Adjust the tire air pressure to the specification.
2. Position the unloaded vehicle on a flat, level surface.
3. Seat one person in the driver’s seat.
4. Position the vehicle 3 m {10 ft} in front of a white
screen.
5. While adjusting one fog light, mask the other.
6. Start the engine to charge the battery.
7. Turn the front fog light on.
8. Peel off the mud guard.
9. Loosen the screw or bolts for the aim adjustment.
10. Move the front fog light in the direction of the
arrows indicated in the figure and adjust the
center of the front fog light to the position.
11. Tighten the front fog light adjusting screw or bolts.
End Of Sie
Z3U0918W006
A3U0918W111
1712-1U-01G(09-18).fm 9 ページ 2001年6月29日 金曜日 午後12時57分
LIGHTING SYSTEMS
09–18–10
REAR COMBINATION LIGHT REMOVAL/INSTALLATION
A3U091851150W01
1. Disconnect the negative battery cable.
2. Remove the trunk side trim. (See 09–17–15 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Socket Installation Note
1. Hook the harness as shown in the figure.
End Of Sie
1
Connector
2
Nut
3
Rear combination light
4
Socket
(See 09–18–10 Socket Installation Note)
5
Brake light/taillight bulb
6
Rear turn light bulb
7
Back-up light bulb
8
Rear side marker light bulb (4SD)
9
Taillight bulb (4SD)
A3U0918W107
A3U0918W106
1712-1U-01G(09-18).fm 10 ページ 2001年6月29日 金曜日 午後12時57分
LIGHTING SYSTEMS
09–18–11
09–18
HIGH-MOUNT BRAKE LIGHT REMOVAL/INSTALLATION
A3U091851580W01
In-Vehicle Type
1. Disconnect the negative battery cable.
2. Remove the rear package trim. (See 09–17–12 REAR PACKAGE TRIM REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
Rear Spoiler Type
1. Disconnect the negative battery cable.
2. Remove the rear spoiler. (See 09–16–8 REAR SPOILER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
1
High-mount brake light
2
Lens
3
Socket
4
High-mount brake light bulb
Y3U918WAM
1
Screw
2
High-mount brake light
(See 09–18–12 High-mount brake light removal
note (4SD))
A3U0918W102
1712-1U-01G(09-18).fm 11 ページ 2001年6月29日 金曜日 午後12時57分
LIGHTING SYSTEMS
09–18–12
High-mount brake light removal note (4SD)
1. Tie a string to the end of the connector of the
high-mount brake light beforehand so that the
connector can be passed easily through the rear
spoiler during installation.
End Of Sie
LICENSE PLATE LIGHT REMOVAL/INSTALLATION
A3U091851270W01
1. Disconnect the negative battery cable.
2. Remove the rear finisher. (See 09–16–3 REAR FINISHER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
License Plate Light Removal Note
1. Slide the license plate light to the arrow mark and
remove it.
End Of Sie
COMBINATION SWITCH REMOVAL/INSTALLATION
A3U091866120W01
1. Disconnect the negative battery cable.
2. Remove the driver-side air bag module. (See 08–10–5 DRIVER-SIDE AIR BAG MODULE REMOVAL/
INSTALLATION.)
3. Remove the steering wheel. (See 06–12–6 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
4. Remove the column cover. (See 09–17–5 COLUMN COVER REMOVAL/INSTALLATION.)
5. Remove the clock spring. (See 08–10–9 CLOCK SPRING REMOVAL/INSTALLATION.)
6. Remove in the order indicated in the table.
7. Install in the reverse order of removal.
End Of Sie
Y3U918WAJ
1
License plate light
(See 09–18–12 License Plate Light Removal Note)
2
Connector
3
Socket
4
License plate light bulb
X3U918WA7
X3U918WA8
1
Connector
2
Screw
3
Combination switch
X3U918WA9
1712-1U-01G(09-18).fm 12 ページ 2001年6月29日 金曜日 午後12時57分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст