Mazda Protege 5. Manual — part 340
LIGHTING SYSTEMS
09–18–13
09–18
COMBINATION SWITCH DISASSEMBLY/ASSEMBLY
A3U091866120W02
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
End Of Sie
LIGHT SWITCH REMOVAL/INSTALLATION
A3U091866121W01
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09–17–5 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
LIGHT SWITCH INSPECTION
A3U091866121W02
Headlight switch
1. Remove the light switch. (See 09–18–13 LIGHT SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the light switch
terminals using an ohmmeter.
•
If not as specified, replace the light switch.
1
Screw
2
Wiper lever
3
Light lever
4
Body
Z3U0918W003
1
Connector
2
Screw
3
Light lever
X3U918WAB
Y3U918WA0
Y3U918WAN
1712-1U-01G(09-18).fm 13 ページ 2001年6月29日 金曜日 午後12時57分
LIGHTING SYSTEMS
09–18–14
Turn switch
1. Remove the light switch. (See 09–18–13 LIGHT SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the light switch
terminals using an ohmmeter.
•
If not as specified, replace the light switch.
End Of Sie
FRONT FOG LIGHT SWITCH REMOVAL/INSTALLATION
A3U091866402W01
1. Disconnect the negative battery cable.
2. Remove the left side side panel from the dashboard.
3. Compress the tabs of the front fog light switch
and pull the switch out of the dashboard.
4. Disconnect the connector to remove the front fog
light switch.
5. Install in the reverse order of removal.
End Of Sie
FRONT FOG LIGHT SWITCH INSPECTION
A3U091866402W02
1. Remove the front fog light switch. (See 09–18–14 FRONT FOG LIGHT SWITCH REMOVAL/INSTALLATION.)
2. Inspect for continuity between the front fog light
switch terminals using an ohmmeter.
•
If not as specified, replace the front fog light
switch.
End Of Sie
HAZARD WARNING SWITCH REMOVAL/INSTALLATION
A3U091866401W01
1. Disconnect the negative battery cable.
2. Remove the center panel. (See 09–17–4 CENTER PANEL REMOVAL/INSTALLATION.)
3. Grasp the tabs of the hazard warning switch and
pull it forward to remove it.
4. Install in the reverse order of removal.
End Of Sie
Y3U918WA1
X3U918WBG
Z3U0918W009
Z3U0918W007
Z3U0918W008
Y3U918WAP
1712-1U-01G(09-18).fm 14 ページ 2001年6月29日 金曜日 午後12時57分
LIGHTING SYSTEMS
09–18–15
09–18
HAZARD WARNING SWITCH INSPECTION
A3U091866401W02
1. Remove the hazard warning switch. (See 09–18–14 HAZARD WARNING SWITCH REMOVAL/
INSTALLATION.)
2. Inspect for continuity between the hazard warning
switch terminals using an ohmmeter.
•
If not as specified, replace the hazard warning
switch.
End Of Sie
BACK-UP LIGHT SWITCH REMOVAL/INSTALLATION
A3U091817640W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
BACK-UP LIGHT SWITCH INSPECTION
A3U091817640W02
1. Disconnect the back-up light switch connector.
2. Inspect for continuity between the back-up light
switch terminals using an ohmmeter.
•
If not as specified, replace the back-up light
switch.
End Of Sie
Y3U918WA2
X3U918WBH
1
Connector
2
Back-up light switch
X3U918WAG
Y3U918WA3
X3U918WBJ
1712-1U-01G(09-18).fm 15 ページ 2001年6月29日 金曜日 午後12時57分
LIGHTING SYSTEMS
09–18–16
FLASHER CONTROL MODULE REMOVAL/INSTALLATION
A3U091866830W01
Note
•
Because the lock section of the control module is damaged easily, do not remove the control module from
the bracket unless replacement is necessary. Always perform an inspection of the flasher control module
before removal.
1. Disconnect the negative battery cable.
2. Remove the bracket.
3. Disconnect the flasher control module connector.
4. Remove the flasher control module by prying the
lock section of the upper part with a flathead
screwdriver.
5. Install in the reverse order of removal.
End Of Sie
FLASHER CONTROL MODULE INSPECTION
A3U091866830W02
1. Remove the bracket and pull it toward you.
2. Measure the voltage at the flasher control module terminals as indicated below.
3. Disconnect the flasher control module connector before inspecting for continuity at terminal F.
•
If not as specified, inspect the parts listed under “Action."
•
If the parts and wiring harnesses are okay but the system still does not work properly, replace the flasher
control module.
Terminal Voltage List (Reference)
X3U918WAJ
Terminal
Signal
Connected
to
Test condition
Voltage (V)/
Continuity
Action
A
Power supply
HAZARD 15
A fuse
Under any condition
B+
•
Inspect HAZARD 15 A fuse
•
Inspect related harness
B
—
—
—
—
—
D
Turn signal
flasher (LH)
Turn signal
light (LH)
Turn signal light (LH) flashes.
Alternates below
1.0 and B+
•
Inspect turn signal light (LH)
•
Inspect related harness
Hazard warning switch at on
position.
Other
Below 1.0
F
Flasher control
module ground
GND
Constant: inspect for
continuity to ground.
Yes
•
Inspect GND
G
Turn signal
flasher (RH)
Turn signal
light (RH)
Turn signal light (RH) flashes.
Alternates below
1.0 and B+
•
Inspect turn signal light (RH)
•
Inspect related harness
Hazard warning switch at on
position.
Other
Below 1.0
H
Hazard
warning on
Hazard
warning
switch
Hazard warning switch at on
position.
Below 1.0
•
Inspect hazard warning switch
(See 09–18–15 HAZARD
WARNING SWITCH
INSPECTION)
•
Inspect related harness
Hazard warning switch at off
position.
B+
I
Turn switch on/
off (RH)
Combination
switch (light
switch)
Ignition switch is at ON and
turn switch (RH) on.
B+
•
Inspect light switch
(See 09–18–13 LIGHT
SWITCH INSPECTION)
•
Inspect TURN 10 A fuse
•
Inspect related harness
Other
Below 1.0
J
Turn switch on/
off (LH)
Combination
switch (light
switch)
Ignition switch is at ON and
turn switch (LH) on.
B+
•
Inspect light switch
(See 09–18–13 LIGHT
SWITCH INSPECTION)
•
Inspect TURN 10 A fuse
•
Inspect related harness
Other
Below 1.0
ZLU918WA6
1712-1U-01G(09-18).fm 16 ページ 2001年6月29日 金曜日 午後12時57分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст