Mazda Protege 5. Manual — part 318
GLASS/WINDOWS/MIRRORS
09–12–27
09–12
7. Press firmly inward on the glass to compress the
sealant.
Hardening time of sealant
8. Check for water leaks. If a leak is found, wipe the
water off well and repeat the installation.
9. Install the C-pillar trim. (See 09–17–11 C-PILLAR
TRIM REMOVAL/INSTALLATION.)
End Of Sie
FILAMENT INSPECTION
A3U091263931W03
1. Turn the ignition switch to ON position.
2. Turn the rear window defroster switch to ON.
3. Connect the positive (+) lead of the voltmeter to the positive side of each filament and the negative (
−
) lead to
ground.
Caution
••••
Directly touching the rear window
defroster filament with the lead of the
circuit tester will damage it. Wrap
aluminum foil around the end of the lead
and test the filament by touching it with
the foil.
4. Gradually, slide the positive (+) lead from the
positive side to the negative side and measure
the voltage. Verify that the voltage decreases
accordingly.
•
If the voltage is not as specified or it changes
rapidly, the filament is faulty. Repair the
filament.
End Of Sie
Temperature
Surface
hardening time
Time required
until car can be
put into service
5
°
C {41
°
F}
Approx. 1.5 h
Approx. 12 h
20
°
C {68
°
F}
Approx. 1 h
Approx. 4 h
35
°
C {95
°
F}
Approx. 10 min.
Approx. 2 h
A3U0912W008
Measurement place
Voltage (Reference value)
(1)
→
(2)
Approx. 12 V
→
Approx. 0 V
X3U912WA1
A3U0912W021
1712-1U-01G(09-12).fm 27 ページ 2001年6月29日 金曜日 午前10時30分
GLASS/WINDOWS/MIRRORS
09–12–28
FILAMENT REPAIR
A3U091263931W04
1. Use isopropyl alcohol to clean around the damaged section of the filament.
2. Attach tape above and below the damaged
section of the filament.
3. Using a small brush or marking pen, repair the
filament with silver paint or equivalent.
4. After approximately 2—3 minutes, carefully
remove the tape without disturbing the repaired
area.
5. Use a hot air blower heated to 150
°°°°
C {302
°°°°
F} for
30 minutes or let the paint set for 24 hours at
25
°°°°
C {77
°°°°
F} to allow it to dry completely.
Caution
••••
Do not use the rear window defroster
until the paint is completely dry. It may
cause other malfunctions if it is used before the paint is dry.
End Of Sie
REAR WINDOW DEFROSTER SWITCH INSPECTION
A3U091266460W01
1. Remove the climate control unit. (See 07–40–9 CLIMATE CONTROL UNIT REMOVAL.)
2. Inspect for continuity between the rear window
defroster switch terminals using an ohmmeter.
3. Connect battery positive voltage to terminal L and
ground to terminal E.
4. Turn the rear window defroster switch to ON.
5. Verify that the LED illuminates.
•
If not as specified, replace the climate control unit.
End Of Sie
POWER OUTSIDE MIRROR INSPECTION
A3U091269110W01
1. Disconnect the power outside mirror connector. (See 09–12–28 POWER OUTSIDE MIRROR REMOVAL/
INSTALLATION.)
2. Apply battery positive voltage to the power outside mirror and inspect the operation of the power outside mirror.
•
If not as specified, replace the power outside mirror.
End Of Sie
POWER OUTSIDE MIRROR REMOVAL/INSTALLATION
A3U091269110W02
1. Disconnect the negative battery cable.
2. Remove the front door trim. (See 09–17–9 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
3. Partially peel off the door screen.
4. Disconnect the connector.
X3U912WA4
Z3U0912W018
Z3U0912W019
Terminal
Mirror operation
B+
GND
B
D
Up
D
B
Down
F
D
Left
D
F
Right
Z3U0912W001
1712-1U-01G(09-12).fm 28 ページ 2001年6月29日 金曜日 午前10時30分
GLASS/WINDOWS/MIRRORS
09–12–29
09–12
5. Remove the nuts, and then remove the power
outside mirror.
6. Install in the reverse order of removal.
End Of Sie
MANUAL OUTSIDE MIRROR REMOVAL/INSTALLATION
A3U091269100W01
1. Remove the inner garnish.
2. Remove the nuts, and then remove the manual
outside mirror.
3. Install in the reverse order of removal.
End Of Sie
OUTSIDE MIRROR GLASS REMOVAL
A3U091269111W01
1. Warm the frame and the mirror glass to approximately 70
°°°°
C {158
°°°°
F} for 3 minutes using a hot air blower.
2. Put on gloves and protective eye wear.
3. Insert a tape-wrapped scraper between the mirror
glass and the frame, and pry the glass loose.
End Of Sie
OUTSIDE MIRROR GLASS INSTALLATION
A3U091269111W02
1. Clean and degrease the adhesion surface of the mirror glass.
2. Stick double-sided adhesive tape onto the back of the mirror glass.
3. Warm up the frame using a hot air blower.
4. Remove the paper backing from the double-sided adhesive tape on the back of the mirror glass.
5. Insert the mirror glass into the frame, then press
lightly on the glass to secure it.
End Of Sie
X3U912WD8
X3U912WD7
X3U912WD9
X3U912WE0
1712-1U-01G(09-12).fm 29 ページ 2001年6月29日 金曜日 午前10時30分
GLASS/WINDOWS/MIRRORS
09–12–30
POWER OUTSIDE MIRROR SWITCH REMOVAL/INSTALLATION
A3U091266600W01
1. Disconnect the negative battery cable.
2. Remove the driver-side front door trim. (See 09–17–9 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
3. Push the clip from the reverse side of the trim to remove the switch panel.
4. Disconnect the connector.
5. Remove the screws, and then remove the power
outside mirror switch.
6. Install in the reverse order of removal.
End Of Sie
POWER OUTSIDE MIRROR SWITCH INSPECTION
A3U091266600W02
1. Remove the power outside mirror switch. (See 09–12–30 POWER OUTSIDE MIRROR SWITCH REMOVAL/
INSTALLATION.)
2. Inspect for continuity between the power outside mirror switch terminals using an ohmmeter.
•
If not as specified, replace the power outside mirror switch.
End Of Sie
REARVIEW MIRROR REMOVAL
A3U091269220W01
1. Insert a flathead screwdriver between the mirror
and the base.
2. Push the base pin down to remove the rearview
mirror.
End Of Sie
X3U912WE2
Z3U0912W014
X3U912WE3
X3U912WE5
1712-1U-01G(09-12).fm 30 ページ 2001年6月29日 金曜日 午前10時30分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст