Mazda Protege 5. Manual — part 302
ON-BOARD DIAGNOSTIC [AUDIO]
09–02B–2
Identification With Printed Numbers/Label
Base unit
1. To identify the supplier name, compare the
leftmost number of the ID code (4 digits), printed
on the upper right corner of the LCD, with the
table below.
Upper/lower module
1. Remove the audio unit.
2. Verify the supplier name written on the label attached on each module.
Identification With On-board Diagnostic Test Mode
1. Start the on-board diagnostic test mode.
2. Verify the device code and supplier code
displayed in the LCD.
Note
•
When no DTCs are in the memory, device
code and supplier codes will not be
displayed.
End Of Sie
DTC CLEARING PROCEDURE
A3U090266900W03
1. Start the on-board diagnostic test mode.
2. First press the POWER button and hold it, then
press AUDIO CONT button for 2 seconds or
more.
Caution
••••
Before clearing the DTCs, be sure to
enter all of them displayed in the on-
board diagnostic test mode on the Audio
Exchange Order Form.
3. To stop the on-board diagnostic test mode, turn
the ignition switch to the LOCK position.
End Of Sie
Audio ID
number
Supplier name
1
Panasonic
2
Clarion
4
FMS Audio
YLE8175W002
Device code
Part name
00
Cassette deck (lower module)
03
CD player (upper module)
05
CD changer (external type)
06
CD changer (upper module)
07
MD player (lower module)
09
Base unit
Supplier code
Supplier name
1
FMS Audio
2
Panasonic
3
Clarion
Z3U0920W003
1
POWER button
2
AUDIO CONT button
YLE8175W004
1712-1U-01G(09-02B).fm 2 ページ 2001年6月29日 金曜日 午前10時27分
ON-BOARD DIAGNOSTIC [AUDIO]
09–02B–3
09–02B
DTC TABLE
A3U090266900W04
*1,*2
: When an error occurs, the error messages are displayed three times in the order of *1 and *2, respectively.
End Of Sie
DTC 09:ER22
A3U090266900W05
Diagnostic procedure
End Of Sie
Screen display
Malfunction location
Page
DTC
Output signal
09:Er22
—
Base unit (peripheral circuit)
(See 09–02B–3 DTC 09:ER22)
09:Er20
—
Power supply circuit of base unit
(See 09–02B–4 DTC 09:ER20)
00:Er10
—
Cassette deck—base unit communication line
(See 09–02B–5 DTC 00:ER10)
03:Er10
—
CD player—base unit communication line
(See 09–02B–5 DTC 03:ER10)
05:Er10
—
CD changer (external type)—base unit
communication line
(See 09–02B–6 DTC 05:ER10)
06:Er10
—
CD changer (upper module)—base unit
communication line
(See 09–02B–6 DTC 06:ER10)
07:Er10
—
MD player—base unit communication line
(See 09–02B–7 DTC 07:ER10)
03:Er01
—
CD player
(See 09–02B–7 DTC 03:ER01)
03:Er02
CHECK
*1
CD
*2
CD player
(See 09–02B–8 DTC 03:ER02)
03:Er07
CHECK
*1
CD
*2
CD player
(See 09–02B–8 DTC 03:ER07)
00:Er01
—
Cassette deck
(See 09–02B–9 DTC 00:ER01)
00:Er03
—
Cassette deck
(See 09–02B–9 DTC 00:ER03)
00:Er04
CHECK
*1
TAPE
*2
Cassette tape
(See 09–02B–9 DTC 00:ER04)
05:Er01
—
CD changer (external type)
(See 09–02B–10 DTC 05:ER01)
05:Er07
CHECK
*1
CD
*2
CD changer (external type)
(See 09–02B–10 DTC 05:ER07)
06:Er01
—
CD changer (upper module)
(See 09–02B–11 DTC 06:ER01)
06:Er02
CHECK
*1
CD
*2
CD changer (upper module)
(See 09–02B–11 DTC 06:ER02)
06:Er07
CHECK
*1
CD
*2
CD changer (upper module)
(See 09–02B–12 DTC 06:ER07)
07:Er01
—
MD player
(See 09–02B–12 DTC 07:ER01)
07:Er02
CHECK
*1
MD
*2
MD player
(See 09–02B–13 DTC 07:ER02)
07:Er07
CHECK
*1
MD
*2
MD player
(See 09–02B–13 DTC 07:ER07)
no Err
—
No stored DTCs
—
DTC 09:Er22
Base unit (peripheral circuit)
DETECTION
CONDITION
•
Base unit detects malfunction in its inner circuit (related to tuner).
POSSIBLE
CAUSE
•
Base unit malfunction
INSPECTION
ACTION
INSPECT BASE UNIT
•
Clear DTC.
•
Turn on radio and operate it for 3 seconds or more.
•
Start on-board diagnostic test mode.
•
Is DTC 09:Er22 displayed?
Yes
Replace base unit.
No
Troubleshooting completed.
1712-1U-01G(09-02B).fm 3 ページ 2001年6月29日 金曜日 午前10時27分
ON-BOARD DIAGNOSTIC [AUDIO]
09–02B–4
DTC 09:ER20
A3U090266900W06
Diagnostic procedure
End Of Sie
DTC 09:Er20
Power supply circuit of base unit
DETECTION
CONDITION
•
Voltage detected at base unit terminals 1B and 1R is less than 8.5 V, or more than 16 V (must not be
16V).
POSSIBLE
CAUSE
•
Weak battery
•
Malfunction in wiring harness between battery and base unit
STEP
INSPECTION
ACTION
1
INSPECT BATTERY
•
Turn headlights ON then OFF to remove surface
charge.
•
Measure battery voltage.
•
Is voltage less than 8.5 V?
Yes
Battery is weak.
•
Inspect charge/discharge system.
No
Go to next step.
2
INSPECT BATTERY
•
Engine running.
•
Measure battery voltage.
•
Is voltage greater than 16 V?
Yes
Battery is overcharging.
•
Inspect charge/discharge system.
No
Go to next step.
3
INSPECT WIRING HARNESS BETWEEN BATTERY
AND FUSE BLOCK
•
Measure voltage at fuse block connector (JB-01)
terminals A and D.
•
Is voltage 8.5 V —16 V?
Yes
Go to next step.
No
Repair wiring harness between battery and fuse
block.
4
INSPECT WIRING HARNESS BETWEEN FUSE
BLOCK AND BASE UNIT
•
Measure voltage at base unit connector terminals 1B
and 1R.
•
Is voltage 8.5 V —16 V?
Yes
Go to next step.
No
Repair wiring harness between fuse block and base
unit.
5
INSPECT BASE UNIT
•
Clear DTC.
•
Turn ignition switch to ACC or ON position and hold
for 30 seconds or more.
•
Start on-board diagnostic test mode.
•
Is DTC 09:Er20 displayed?
Yes
Replace base unit.
No
Troubleshooting completed.
1712-1U-01G(09-02B).fm 4 ページ 2001年6月29日 金曜日 午前10時27分
ON-BOARD DIAGNOSTIC [AUDIO]
09–02B–5
09–02B
DTC 00:ER10
A3U090266900W07
Diagnostic procedure
End Of Sie
DTC 03:ER10
A3U090266900W08
Diagnostic procedure
End Of Sie
DTC 00:Er10
Cassette deck—base unit communication line
DETECTION
CONDITION
•
Base unit detects communication error with cassette deck (lower module).
POSSIBLE
CAUSE
•
Malfunction of connectors between base unit and cassette deck (lower module)
•
Cassette deck (lower module) malfunction
•
Base unit malfunction
STEP
INSPECTION
ACTION
1
INSPECT CONNECTOR
•
Remove cassette deck (lower module) and inspect
connector for the following.
— Deformation of pin
— Poor connection of female terminal
— Pinching of foreign material
•
Is connector okay?
Yes
Go to next step.
No
Repair connector, then go to next step.
2
VERIFY THAT CASSETTE DECK (LOWER MODULE)
IS INSTALLED WITH BASE UNIT
•
Install cassette deck (lower module) and verify its
installation condition.
•
Is cassette deck securely installed?
Yes
Go to next step.
No
Securely install cassette deck (lower module), then
go to next step.
3
INSPECT CASSETTE DECK (LOWER MODULE)
•
Clear DTC.
•
Turn ignition switch to ACC or ON position and hold
for 3 seconds or more.
•
Start on-board diagnostic test mode.
•
Is DTC 00:Er10 displayed?
Yes
Replace base unit and cassette deck (lower module).
No
Troubleshooting completed.
DTC 03:Er10
CD player—base unit communication line
DETECTION
CONDITION
•
Base unit detects communication error with CD player (upper module).
POSSIBLE
CAUSE
•
Malfunction of connectors between base unit and CD player (upper module)
•
CD player (upper module) malfunction
•
Base unit malfunction
STEP
INSPECTION
ACTION
1
INSPECT CONNECTOR
•
Remove CD player (upper module) and inspect
connector for the following.
— Deformation of pin
— Poor connection of female terminal
— Pinching of foreign material
•
Is connector okay?
Yes
Go to next step.
No
Repair connector, then go to next step.
2
VERIFY THAT CD PLAYER (UPPER MODULE) IS
INSTALLED WITH BASE UNIT
•
Install CD player (upper module) and verify its
installation condition.
•
Is CD player securely installed?
Yes
Go to next step.
No
Securely install CD player (upper module), then go to
next step.
3
INSPECT CD PLAYER (UPPER MODULE)
•
Clear DTC.
•
Turn ignition switch to ACC or ON position and wait
for 3 seconds or more.
•
Start on-board diagnostic test mode.
•
Is DTC 03:Er10 displayed?
Yes
Replace base unit and CD player (upper module).
No
Troubleshooting completed.
1712-1U-01G(09-02B).fm 5 ページ 2001年6月29日 金曜日 午前10時27分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст