Mazda Protege 5. Manual — part 300
SEAT BELT
08–11–2
REAR SEAT BELT REMOVAL/INSTALLATION
A3U081157730W01
Caution
••••
The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be
rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the
retractor.
4SD
1. Remove the rear package trim.
2. Remove the bolts, then remove the rear seat belt.
3. Install in the reverse order of removal.
5HB
1. Remove the trunk side trim.
2. Remove the bolts, then remove the rear seat belt.
3. Install in the reverse order of removal.
End Of Sie
Z3U0811W004
A3U0811W001
1712-1U-01G(08-11).fm 2 ページ 2001年6月29日 金曜日 午前10時25分
SEAT BELT
08–11–3
08–11
REAR CENTER SEAT BELT REMOVAL/INSTALLATION
A3U081157730W02
Caution
••••
The ELR has a spring that will unwind if the retractor's cover is removed. The spring cannot be
rewound by hand. If this occurs, the ELR will not work properly. Therefore, do not disassemble the
retractor.
4SD
1. Remove the rear package trim.
2. Remove the bolt, then remove the rear center
seat belt.
3. Install in the reverse order of removal.
5HB
1. Remove the trunk side trim.
2. Remove the bolts, then remove the rear center
seat belt.
3. Install in the reverse order of removal.
End Of Sie
FRONT BUCKLE REMOVAL/INSTALLATION
A3U081157620W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
Z3U0811W002
A3U0811W002
1
Connector
2
Front buckle
X3U811WA3
1712-1U-01G(08-11).fm 3 ページ 2001年6月29日 金曜日 午前10時25分
SEAT BELT
08–11–4
REAR BUCKLE REMOVAL/INSTALLATION
A3U081157720W01
1. For 4SD, remove the rear seat cushion. For 5HB, lift up the rear seat cushion.
2. Remove the bolt, then remove the rear buckle.
3. Install in the reverse order of removal.
End Of Sie
SEAT BELT INSPECTION
A3U081157630W02
Belt
1. Confirm that the seat belt is installed correctly.
2. Inspect the seat belt for damage and deformation of metal parts.
•
If any damage is found, replace as necessary.
3. Replace the seat belt if there is any faulty area.
ELR
1. Verify that the belt can be pulled out smoothly,
and that it moves smoothly when wound.
•
If not as specified, replace the seat belt.
2. Verify that the retractor locks when the belt is
pulled quickly.
•
If not as specified, replace the seat belt.
3. Remove the retractor. (See 08–11–1 FRONT
SEAT BELT REMOVAL/INSTALLATION.) (See
08–11–2 REAR SEAT BELT REMOVAL/
INSTALLATION.) (See 08–11–3 REAR CENTER
SEAT BELT REMOVAL/INSTALLATION.)
4. Hold the retractor as it would be installed.
5. Slowly incline the retractor while pulling out the
belt.
6. Verify that the retractor lks at approximately 30
°
inclination.
•
If not as specified, replace the seat belt.
ALR
1. Pull the belt out fully and the lock mode changes from ELR to ALR.
2. Verify that retractor makes a clicking sound as the belt slowly retracts.
•
If no sound is heard, the lock mode has not changed to ALR. If necessary, repeat the above Step 1.
•
If not as specified, replace the seat belt.
3. Verify that the belt locks when pulled.
•
If not as specified, replace the seat belt.
4. Verify that the lock mode changes to ELR when the belt fully retracts.
•
If not as specified, replace the seat belt.
End Of Sie
Z3U0811W001
X3U811WA5
X3U811WA6
1712-1U-01G(08-11).fm 4 ページ 2001年6月29日 金曜日 午前10時25分
SEAT BELT
08–11–5
08–11
BUCKLE SWITCH INSPECTION
A3U081157620W02
1. Disconnect the negative battery cable.
2. Disconnect the buckle switch connector.
3. Inspect for continuity between the buckle switch
terminals using an ohmmeter.
•
If not as specified, replace the front buckle.
End Of Sie
CHILD RESTRAINT SEAT ANCHOR REMOVAL/INSTALLATION
A3U081157770W01
ISOFIX Anchor
1. Fold down the rear seat back.
2. Remove the tire house trim.
3. Remove the child restraint seat anchor.
4. Install in the reverse order of removal.
Tether Anchor
4SD
1. Remove the rear package trim.
2. Remove the bolt, then child restraint seat anchor.
3. Install in the reverse order of removal.
5HB
1. Remove the trunk end trim.
2. Remove the bolt, then child restraint seat anchor.
3. Install in the reverse order of removal.
End Of Sie
Y3U811WA0
X3U811WA7
Z3U0811W003
A3U0811W004
A3U0811W005
1712-1U-01G(08-11).fm 5 ページ 2001年6月29日 金曜日 午前10時25分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст