Mazda Protege 5. Manual — part 193
REAR AXLE
03–12–1
03–12
03–12
REAR AXLE
REAR AXLE LOCATION INDEX. . . . . . . 03–12–1
WHEEL HUB, HUB SPINDLE
PRE-INSPECTION . . . . . . . . . . . . . . . . 03–12–1
Wheel Bearing Play Inspection . . . . . . 03–12–1
WHEEL HUB, HUB SPINDLE
(DRUM BRAKE TYPE)
REMOVAL/INSTALLATION . . . . . . . . . 03–12–2
Locknut Removal Note. . . . . . . . . . . . . 03–12–3
ABS Sensor Rotor (With ABS)
Removal Note . . . . . . . . . . . . . . . . . . 03–12–3
ABS Sensor Rotor (With ABS)
Installation Note . . . . . . . . . . . . . . . . . 03–12–3
Locknut Installation Note . . . . . . . . . . . 03–12–4
WHEEL HUB, HUB SPINDLE
(DISC BRAKE TYPE)
REMOVAL/INSTALLATION . . . . . . . . . . 03–12–4
ABS Sensor Rotor (With ABS)
Installation Note . . . . . . . . . . . . . . . . . 03–12–5
End of Toc
REAR AXLE LOCATION INDEX
A3U031205000W01
.
End Of Sie
WHEEL HUB, HUB SPINDLE PRE-INSPECTION
A3U031205000W02
Wheel Bearing Play Inspection
1. Position a dial indicator against the brake drum
(brake drum type), or wheel hub (disc brake type).
2. Push and pull the rear brake component by hand
in the axial direction and measure the wheel
bearing play.
•
If the bearing play exceeds the specification,
replace the wheel hub component as
necessary and tighten the locknut to the
specified torque and retest.
Wheel bearing play
0.05 mm {0.002 in}
End Of Sie
Z3U0312W005
1
Wheel hub, hub spindle
(See 03–12–1 WHEEL HUB, HUB SPINDLE
PRE-INSPECTION)
(See 03–12–4 WHEEL HUB, HUB SPINDLE (DISC
BRAKE TYPE) REMOVAL/INSTALLATION)
(See 03–12–2 WHEEL HUB, HUB SPINDLE
(DRUM BRAKE TYPE) REMOVAL/
INSTALLATION)
X3U312WA0
1712-1U-01G(03-12).fm 1 ページ 2001年6月29日 金曜日 午前9時58分
REAR AXLE
03–12–2
WHEEL HUB, HUB SPINDLE (DRUM BRAKE TYPE) REMOVAL/INSTALLATION
A3U031205000W03
Caution
••••
Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while servicing the vehicle.
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
.
Z3U0312W001
1
ABS-wheel speed sensor
2
Hub cap
3
Locknut
(See 03–12–3 Locknut Removal Note)
(See 03–12–4 Locknut Installation Note)
4
Brake drum
5
Wheel hub and ABS sensor rotor (with ABS)
6
ABS sensor rotor (with ABS)
(See 03–12–3 ABS Sensor Rotor (With ABS)
Removal Note)
(See 03–12–3 ABS Sensor Rotor (With ABS)
Installation Note)
7
Hub bolt
(See 03–11–5 Hub Bolt Removal Note)
(See 03–11–5 Hub Bolt Installation Note)
8
Wheel hub
9
Parking brake cable
10
Brake pipe
11
Rear brake component
12
Hub spindle
1712-1U-01G(03-12).fm 2 ページ 2001年6月29日 金曜日 午前9時58分
REAR AXLE
03–12–3
03–12
Locknut Removal Note
1. Raise the staked portion of the locknut using a
small cape chisel and a hammer.
2. Lock the hub by applying the brakes.
3. Remove the locknut.
ABS Sensor Rotor (With ABS) Removal Note
Note
•
The sensor rotor does not need to be removed unless it is being replaced.
1. Remove the sensor rotor using a chisel.
ABS Sensor Rotor (With ABS) Installation Note
1. Set the SST as shown in the figure.
Caution
••••
Position the SST so that marking A faces
the bottom.
2. Press on the new sensor rotor using the SST and
a press.
X3U312WA2
X3U312WA3
X3U312WA4
A3U0312W003
1712-1U-01G(03-12).fm 3 ページ 2001年6月29日 金曜日 午前9時58分
REAR AXLE
03–12–4
Locknut Installation Note
1. Install a new locknut and stake it as shown.
End Of Sie
WHEEL HUB, HUB SPINDLE (DISC BRAKE TYPE) REMOVAL/INSTALLATION
A3U031205000W04
Caution
••••
Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and set it to an appropriate
place where the sensor will not be pulled by mistake while servicing the vehicle.
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
.
X3U312WA5
A3U0312W001
1
ABS wheel-speed sensor
2
Hub cap
3
Locknut
(See 03–12–2 WHEEL HUB, HUB SPINDLE
(DRUM BRAKE TYPE) REMOVAL/
INSTALLATION)
4
Brake caliper component
5
Disc plate
6
Wheel hub and ABS sensor rotor
7
ABS sensor rotor
(See 03–12–2 WHEEL HUB, HUB SPINDLE
(DRUM BRAKE TYPE) REMOVAL/
INSTALLATION)
(See 03–12–5 ABS Sensor Rotor (With ABS)
Installation Note)
8
Hub bolt
9
Wheel hub component
10
Dust cover
11
Hub spindle
1712-1U-01G(03-12).fm 4 ページ 2001年6月29日 金曜日 午前9時58分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст