Mazda Protege 5. Manual — part 132
LUBRICATION
01–11–8
2. Install the new gaskets onto the oil pump body
and the rear cover with the projections in the
notches as shown. (ZM model)
3. Apply silicone sealant onto the area of oil pan
gasket indicated by A and B. (ZM model)
Thickness
2.0 mm {0.079 in}
4. Apply silicone sealant to the oil pan along the
inside of the bolt holes and overlap the ends.
Thickness
ZM: 2.5—3.5 mm {0.099—0.137 in}
FS: 2.0—3.0 mm {0.079—0.118 in}
Integrated Stiffener Installation Note
ZM
1. Hand-tighten the lock bolt A.
X3U111WAH
X3U111WAJ
X3U111WAK
X3U111WAL
1712-1U-01G(01-11).fm 8 ページ 2001年6月29日 金曜日 午前9時40分
LUBRICATION
01–11–9
01–11
2. Hand-tighten the lock bolt B.
3. Tighten the lock bolt C.
Tightening torque
37—52 N·m {3.8—5.3 kgf·m, 27.3—38.3 ft·lbf}
4. Tighten the lock bolt D.
Tightening torque
37—52 N·m {3.8—5.3 kgf·m, 27.3—38.3 ft·lbf}
5. Tighten the lock bolt A .
Tightening torque
37—52 N·m {3.8—5.3 kgf·m, 27.3—38.3 ft·lbf}
6. Tighten the lock bolt B.
Tightening torque
37—52 N·m {3.8—5.3 kgf·m, 27.3—38.3 ft·lbf}
End Of Sie
X3U111WAM
Y3A1111W001
X3U111WAL
X3U111WAM
1712-1U-01G(01-11).fm 9 ページ 2001年6月29日 金曜日 午前9時40分
LUBRICATION
01–11–10
OIL PUMP REMOVAL/INSTALLATION
A3U011119220W01
1. Remove the timing belt. (See 01–10A–9 TIMING BELT REMOVAL/INSTALLATION [ZM].) (See 01–10B–8
TIMING BELT REMOVAL/INSTALLATION [FS].)
2. Remove the timing belt pulley.
3. Remove the oil pan. (See 01–11–4 OIL PAN REMOVAL/INSTALLATION.)
4. Remove the A/C compressor with the pipe still connected.
5. Remove the A/C compressor bracket.
6. Remove the generator. (ZM)
7. Remove the transaxle (FS) (See 05–15B–4 MANUAL TRANSAXLE (MTX) REMOVAL/INSTALLATION
[G15M-R].) (See 05–17–31 AUTOMATIC TRANSAXLE (ATX) REMOVAL/INSTALLATION.)
8. Remove in the order indicated in the table.
9. Install in the reverse order of removal.
.
Y3U111WA1
1
Oil pump
(See 01–11–12 Oil Pump Removal Note)
(See 01–11–12 Oil Pump Installation Note)
1712-1U-01G(01-11).fm 10 ページ 2001年6月29日 金曜日 午前9時40分
LUBRICATION
01–11–11
01–11
.
Oil Pan Upper Block Removal Note
1. Remove the two bolts at the rear of the cylinder block.
2. Loosen the oil pan upper block bolts in 2 or 3
steps in the order shown.
Z3U0111W998
1
Oil pan upper block
(See 01–11–11 Oil Pan Upper Block Removal Note)
(See 01–11–13 Oil Pan Upper Block Installation
Note)
2
Oil pump
(See 01–11–12 Oil Pump Removal Note)
(See 01–11–12 Oil Pump Installation Note)
Y3U111WA3
1712-1U-01G(01-11).fm 11 ページ 2001年6月29日 金曜日 午前9時40分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст