Mazda Protege 5. Manual — part 335
INTERIOR TRIM
09–17–10
5. Remove the screws and fasteners.
6. Disengage clips C using a fastener remover.
7. Pull the rear door trim upward, then disengage
pins D from the body.
8. Disconnect the power window sub switch
connector if equipped.
9. Remove the inner handle from the rear door trim.
10. Install in the reverse order of removal.
End Of Sie
A-PILLAR TRIM REMOVAL/INSTALLATION
A3U091768160W01
1. Turn the seaming welt over.
2. Disengage clips A and B using a fastener
remover.
3. Pull the A-pillar trim upward, then disengage
hooks C and D.
4. Install in the reverse order of removal.
End Of Sie
B-PILLAR LOWER TRIM REMOVAL
A3U091768220W01
Warning
••••
Handling the side air bag sensor improperly can accidentally deploy the side air bag module,
which may seriously injure you. Read AIR BAG SYSTEM SERVICE WARNINGS before working
around the B-pillar areas. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)
Note
•
The side air bag sensor is located in the B-pillar.
1. Disconnect the negative battery cable.
2. Remove the front scuff plate.
3. Remove the rear scuff plate.
4. Pull the area marked A, then remove one side of
the B-pillar lower trim.
End Of Sie
A3U0916W017
Y3U917WA5
X3U917WAS
1712-1U-01G(09-17).fm 10 ページ 2001年6月29日 金曜日 午前10時35分
INTERIOR TRIM
09–17–11
09–17
B-PILLAR LOWER TRIM INSTALLATION
A3U091768220W02
Warning
••••
Handling the side air bag sensor improperly can accidentally deploy the side air bag module,
which may seriously injure you. Read AIR BAG SYSTEM SERVICE WARNINGS before working
around the B-pillar areas. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)
Note
•
The side air bag sensor is located in the B-pillar.
1. Disconnect the negative battery cable.
2. Install the B-pillar lower trim to the B-pillar with setting 5—10 mm {0.20—0.39 in} upward from its original
installation place.
3. Slide the B-pillar lower trim downward.
4. Install the rear scuff plate.
5. Install the front scuff plate.
End Of Sie
B-PILLAR UPPER TRIM REMOVAL/INSTALLATION
A3U091768210W01
1. Remove the upper anchor of the front seat belt. (See 08–11–1 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
2. Remove the B-pillar lower trim. (See 09–17–10 B-PILLAR LOWER TRIM REMOVAL.) (See 09–17–11 B-
PILLAR LOWER TRIM INSTALLATION.)
3. Turn the seaming welt over.
4. Disengage clip A using a fastener remover.
5. Pull the B-pillar upper trim upward, then
disengage hooks B from the body.
6. Install in the reverse order of removal.
End Of Sie
C-PILLAR TRIM REMOVAL/INSTALLATION
A3U091768240W01
4SD
1. Remove the tire house trim.
2. Turn the seaming welt over.
3. Disengage clips A and pin B using a fastener
remover.
4. Pull the C-pillar trim upward, then disengage hook
C from the body.
5. Install in the reverse order of removal.
Y3U917WA6
Y3U917WA7
1712-1U-01G(09-17).fm 11 ページ 2001年6月29日 金曜日 午前10時35分
INTERIOR TRIM
09–17–12
5HB
1. Remove the trunk side trim.
2. Remove the rear center seat belt upper anchor installation bolt. (LH only)
3. Remove the fastener.
4. Disengage clips A and pins B using a fastener
remover.
5. Pull the C-pillar trim upward, then disengage
hooks C from the body.
6. Install in the reverse order of removal.
End Of Sie
REAR PACKAGE TRIM REMOVAL/INSTALLATION
A3U091768320W01
4SD
1. Remove the rear seat back.
2. Pull the rear package trim upward, then
disengage clips A, pins B and tabs C from the
body.
3. Pull the rear package trim toward you, then
disengage tabs D from the body.
4. Install in the reverse order of removal.
5HB
1. Remove the straps from the strap hangers.
2. Pull the rear package trim, then remove the hinge
pin from the trunk side trim.
3. Install in the reverse order of removal.
End Of Sie
A3U0917W001
Z3U0917W001
A3U0917W003
1712-1U-01G(09-17).fm 12 ページ 2001年6月29日 金曜日 午前10時35分
INTERIOR TRIM
09–17–13
09–17
FRONT SCUFF PLATE REMOVAL/INSTALLATION
1. Pull the front scuff plate upward, then disengage
clips A from the body.
2. Install in the reverse order of removal.
End Of Sie
REAR SCUFF PLATE REMOVAL/INSTALLATION
1. Pull the rear scuff plate upward, then disengage
clips A and B from the body.
2. Install in the reverse order of removal.
End Of Sie
FRONT SIDE TRIM REMOVAL/INSTALLATION
1. Remove the front scuff plate.
2. Turn the seaming welt over.
3. Remove the fasteners.
4. Pull the front side trim toward you, then
disengage clip A, pins B and C from the body.
5. Install in the reverse order of removal.
End Of Sie
TIRE HOUSE TRIM REMOVAL/INSTALLATION
A3U091768760W01
4SD
1. Remove the rear seat back.
2. Remove the rear scuff plate.
3. Remove the rear package trim.
4. Remove the lower anchor installation bolt from
the rear seat belt.
5. Remove the fasteners.
6. Pull the tire house trim forward, then remove the
tire house trim.
7. Install in the reverse order of removal.
X3U917WAW
X3U917WAX
X3U917WAY
X3U917WAZ
1712-1U-01G(09-17).fm 13 ページ 2001年6月29日 金曜日 午前10時35分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст