Mazda Protege 5. Manual — part 334
INTERIOR TRIM
09–17–6
Boot Panel Removal Note
1. Pull the boot panel upward, then disengage clips
A and B from the console.
Console Cover Removal Note
1. Disengage clip A using a tape-wrapped flathead
screwdriver.
2. Pull the console cover upward, then disengage
hook B from the console.
End Of Sie
CONSOLE DISASSEMBLY/ASSEMBLY
A3U091764310W03
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
End Of Sie
Y3E7742W301
Y3E7742W302
1
Screw A
2
Side wall
3
Cover
4
Screw B (MTX)
5
Screw C (MTX)
6
Boot (MTX)
7
Screw D
8
Screw E
9
Console lid hinge
10
Console lid inner
11
Screw F
12
Console lid lock
13
Console lid outer
14
Ashtray
15
Screw G
16
Bracket
Y3E7742W305
1712-1U-01G(09-17).fm 6 ページ 2001年6月29日 金曜日 午前10時35分
INTERIOR TRIM
09–17–7
09–17
GLOVE COMPARTMENT REMOVAL/INSTALLATION
A3U091764030W01
1. Bend the stoppers inward, then remove them.
2. Pull the glove compartment toward you while
pushing it downward (1), then remove clip A.
3. Slide the glove compartment toward driver's side
door (2).
4. Install in the reverse order of removal.
End Of Sie
LOWER PANEL REMOVAL/INSTALLATION
A3U091764280W01
Driver’s side
1. Pull the upper side of the lower panel downward,
then disengage clips A and pins B from the
dashboard.
2. Pull the lower panel toward you, then disengage
hooks C from the dashboard.
3. Install in the reverse order of removal.
Passenger’s side
1. Remove the glove compartment.
2. Remove the screws.
3. Install in the reverse order of removal.
End Of Sie
X3U917WAG
X3U917WAH
Z3U0917W003
Z3U0917W004
1712-1U-01G(09-17).fm 7 ページ 2001年6月29日 金曜日 午前10時35分
INTERIOR TRIM
09–17–8
METER HOOD REMOVAL/INSTALLATION
A3U091755420W01
1. Remove the screws.
2. Pull the meter hood toward you, then remove
clips A and pins B from the dashboard.
3. Install in the reverse order of removal.
End Of Sie
SIDE PANEL REMOVAL/INSTALLATION
A3U091764960W01
1. Remove clips A using a tape-wrapped flathead
screwdriver.
2. Install in the reverse order of removal.
End Of Sie
SIDE WALL REMOVAL/INSTALLATION
A3U091768371W01
1. Remove the fastener.
2. Pull the side wall indicated toward the arrow and
disengage hook A from the body.
3. Install in the reverse order of removal.
End Of Sie
X3U917WAL
X3U917WAM
Y3U917WA3
1712-1U-01G(09-17).fm 8 ページ 2001年6月29日 金曜日 午前10時35分
INTERIOR TRIM
09–17–9
09–17
FRONT DOOR TRIM REMOVAL/INSTALLATION
A3U091768420W01
1. Remove the inner garnish.
2. Remove the regulator handle if equipped.
3. Remove screws A and the fastener.
4. Slide the pull handle cover toward the front of the
vehicle, then disengage tab B from the front door
trim.
5. Remove the screws C.
6. Disengage clips D using a fastener remover from
the body.
7. Pull the front door trim upward, then disengage
pins E from the body.
8. Extract the inner handle from the front door trim.
9. Disconnect the power window main switch
connector (driver’s side).
10. Disconnect the power window sub switch
connector (passenger’s side).
11. Install in the reverse order of removal.
End Of Sie
REAR DOOR TRIM REMOVAL/INSTALLATION
A3U091768520W01
1. Disconnect the negative battery cable if equipped with power window.
2. Remove the regulator handle if equipped.
3. Insert a tape-wrapped fastener remover under the
pull-handle cover, and disengage tab A.
4. Insert a tape-wrapped flathead screwdriver into
the access hole under the forward pull-handle
cover, and remove the pull-handle cover by
pulling it upward and diagonally while pushing clip
B.
Z3U0917W005
A3U0916W015
A3U0916W016
1712-1U-01G(09-17).fm 9 ページ 2001年6月29日 金曜日 午前10時35分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст