Mazda Protege 5. Manual — part 313
GLASS/WINDOWS/MIRRORS
09–12–7
09–12
Power Window Motor Disassembly Note
1. Make marks on the gear and the base before
disassembling the power window motor.
Power Window Motor Assembly Note
1. Align the marks on the gear and the base before assembling the power window motor.
End Of Sie
REAR MANUAL WINDOW REGULATOR REMOVAL/INSTALLATION
A3U091272561W01
1. Remove the rear door glass. (See 09–12–4 REAR DOOR GLASS AND GUIDE REMOVAL/INSTALLATION.)
2. Remove the bolts, then remove the rear manual window regulator.
Tightening torque
6.87—9.80 N·m {70—100 kgf·cm, 60.8—86.7 in·lbf}
3. Install in the reverse order of removal.
End Of Sie
POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION
A3U091266350W01
1. Disconnect the negative battery cable.
2. Remove the driver-side front door trim. (See 09–17–9 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
3. Push out the clip from the reverse side of the trim,
and remove the switch panel.
4. Remove the screw, and remove the power
window main switch.
5. Install in the reverse order of removal.
End Of Sie
X3U912WC3
X3U912WC4
1712-1U-01G(09-12).fm 7 ページ 2001年6月29日 金曜日 午前10時30分
GLASS/WINDOWS/MIRRORS
09–12–8
POWER WINDOW MAIN SWITCH INSPECTION
A3U091266350W02
1. Remove the power window main switch. (See 09–12–7 POWER WINDOW MAIN SWITCH REMOVAL/
INSTALLATION.)
2. When inspecting the passenger’s side and the rear, turn the power-cut switch to ON.
3. Inspect for continuity between the power window main switch terminals using an ohmmeter.
•
If not as specified, replace the power window main switch.
End Of Sie
Y3U912WA2
Z3U0912W003
Z3U0912W004
Z3U0912W005
Z3U0912W006
Z3U0912W007
1712-1U-01G(09-12).fm 8 ページ 2001年6月29日 金曜日 午前10時30分
GLASS/WINDOWS/MIRRORS
09–12–9
09–12
POWER WINDOW SUBSWITCH REMOVAL/INSTALLATION
A3U091266370W01
Passenger’s side
1. Disconnect the negative battery cable.
2. Remove the passenger-side front door trim. (See 09–17–9 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
3. Push out the clip from the reverse side of the trim,
and remove the switch panel.
4. Remove the screw, and remove the power
window subswitch.
5. Install in the reverse order of removal.
Rear
1. Disconnect the negative battery cable.
2. Remove the tab by inserting a tape-wrapped,
flathead screwdriver between the switch and the
rear door trim.
3. Disconnect the connector, and remove the power
window subswitch.
4. Install in the reverse order of removal.
End Of Sie
X3U912WD0
Y3U912WAK
1712-1U-01G(09-12).fm 9 ページ 2001年6月29日 金曜日 午前10時30分
GLASS/WINDOWS/MIRRORS
09–12–10
POWER WINDOW SUBSWITCH INSPECTION
A3U091266370W02
1. If inspecting the passenger’s side, remove the switch panel.
2. If inspecting the rear, remove the power window subswitch.
3. Inspect for continuity between the power window subswitch terminals using an ohmmeter.
•
If not as specified, replace the power window subswitch.
End Of Sie
REGULATOR HANDLE REMOVAL
A3U091258580W01
1. Remove the regulator handle clip using a rag as
shown.
End Of Sie
REGULATOR HANDLE INSTALLATION
A3U091258580W02
1. Install the clip in the regulator handle.
2. Close the door glass fully and push the regulator
handle on as shown.
End Of Sie
Y3U912WA3
Z3U0912W008
Y3U912WA4
Z3U0912W009
X3U912WD5
Z3U0912W002
1712-1U-01G(09-12).fm 10 ページ 2001年6月29日 金曜日 午前10時30分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст