Mazda Protege 5. Manual — part 7
GENERAL INFORMATION
00–00–25
00–00
End Of Sie
SAE STANDARDS
A3U000000003W01
•
In accordance with new regulations, SAE (Society of Automotive Engineers) standard names and
abbreviations are now used in this manual. The table below lists the names and abbreviations that have been
used in Mazda manuals up to now and their SAE equivalents.
#1 : Diagnostic trouble codes depend on the diagnostic test mode
#2 : Controlled by the PCM
#3 : Device that controls engine and powertrain
#4 : Directly connected to exhaust manifold
X3U000WBT
SAE Standard
Remar
k
Abbreviation
Name
AP
Accelerator Pedal
ACL
Air Cleaner
A/C
Air Conditioning
BARO
Barometric Pressure
B+
Battery Positive Voltage
CMP sensor Camshaft Position Sensor
CAC
Charge Air Cooler
CLS
Closed Loop System
CTP
Closed Throttle Position
CPP
Clutch Pedal Position
CIS
Continuous Fuel Injection
System
CKP sensor Crankshaft Position Sensor
DLC
Data Link Connector
DTM
Diagnostic Test Mode
#1
DTC
Diagnostic Trouble Code(s)
DI
Distributor Ignition
EI
Electronic Ignition
#2
ECT
Engine Coolant Temperature
EM
Engine Modification
EVAP
Evaporative Emission
EGR
Exhaust Gas Recirculation
FC
Fan Control
FF
Flexible Fuel
4GR
Fourth Gear
GEN
Generator
GND
Ground
HO2S
Heated Oxygen Sensor
With
heater
IAC
Idle Air control
IAT
Intake Air Temperature
KS
Knock Sensor
MIL
Malfunction Indicator Lamp
MAP
Manifold Absolute Pressure
MAF sensor Mass Air Flow Sensor
MFI
Multiport Fuel Injection
OBD
On-Board Diagnostic
OL
Open Loop
OC
Oxidation Catalytic Converter
O2S
Oxygen Sensor
PNP
Park/Neutral Position
PSP
Power Steering Pressure
PCM
Powertrain Control Module
#3
PAIR
Pulsed Secondary Air
Injection
Pulsed
injection
AIR
Secondary Air Injection
Injection
with air
pump
SAPV
Secondary Air Pulse Valve
SFI
Sequential Multipoint Fuel
Injection
3GR
Third Gear
TWC
Three Way Catalytic
Converter
TB
Throttle Body
TP sensor
Throttle Position Sensor
TCC
Torque Converter Clutch
TCM
Transmission (Transaxle)
Control Module
TR
Transmission (Transaxle)
Range
TC
Turbocharger
VSS
Vehicle Speed Sensor
VR
Voltage Regulator
VAF sensor
Volume Air Flow Sensor
WUTWC
Warm Up Three Way
Catalytic Converter
#4
WOT
Wide Open Throttle
SAE Standard
Remar
k
Abbreviation
Name
GENERAL INFORMATION
00–00–26
End Of Sie
ABBREVIATIONS
A3U000000011W01
End Of Sie
AAS
Air adjusting screw
ABS
Antilock brake system
ACC
Accessories
ATF
Automatic transaxle fluid
ATX
Automatic transaxle
BDC
Bottom dead center
BTDC
Before top dead center
CDCV
Canister drain cut valve
CCM
Comprehensive component monitor
CM
Control module
DC
Drive cycle
DRL
Daytime running light
E/L
Electric load
ELR
Emergency locking retractor
EX
Exhaust
HI
High
HU
ABS hydraulic unit
HVAC
Heater, ventilation, and air conditioning
IG
Ignition
IN
Intake
INT
Intermittent
LF
Left front
LH
Left hand
LO
Low
LR
Left rear
M
Motor
MAX
Maximum
MTX
Manual transaxle
O/D
Overdrive
OFF
Switch off
ON
Switch on
PCV
Positive crankcase ventilation
PRC
Pressure regulator control
P/S
Power steering
RF
Right front
RH
Right hand
RR
Right rear
SST
Special service tool
SW
Switch
TAS
Throttle adjusting screw
TDC
Top dead center
TNS
Tail number side lights
TR
Transmission range
VICS
Variable inertia charging system
VTCS
Variable tumble control system
1GR
First gear
2GR
Second gear
4SD
4 door sedan
5HB
5 door hatchback
GENERAL INFORMATION
00–00–27
00–00
PRE-DELIVERY INSPECTION
A3U000000012W01
Pre-Delivery Inspection Table
Exterior
INSPECT and ADJUST, if necessary, the following items to specification:
Glass, exterior bright metal and paint for damage
Wheel lug nuts
All weatherstrips for damage or detachment
Operation of hood release and lock
Operation of trunk lid and fuel lid opener
Door operation and alignment
Headlight aiming
INSTALLthe following parts:
Wheel caps
Under hood—engine off
INSPECTand ADJUST, if necessary, the following items to specification:
Fuel, engine coolant, and hydraulic lines, fittings, connections, and components for leaks
Engine oil level
Power steering fluid level
Brake and clutch fluid level
Windshield washer reservoir fluid level
Radiator coolant level and specific gravity
Tightness of water hose clamps
Tightness of battery terminals, electrolyte level and specific gravity
Drive belt(s) tension
Accelerator cable and linkage for free movement CLEAN the spark plugs
Interior
INSPECT the operations of the following items:
Seat controls (slide and recline) and headrests
Folding rear seat (if equipped)
Door locks, including childproof door locks (if equipped)
Seat belts and warning system
Ignition switch and steering lock
Air bag system using warning light
Cruise control system (if equipped)
Shift-lock system (if equipped)
Starter interlock
All lights including warning, and indicator lights
Sound warning system
Horn, wipers, and washers
Wiper blades performance
Clean wiper blades and windshield, if necessary
Antenna
Audio system (if equipped)
Cigarette lighter and clock
Power windows (if equipped)
eater, defroster, and air conditioner at various mode selections (if equipped)
INSPECT the following items:
Presence of spare fuse
Upholstery and interior finish
INSPECT and ADJUST, if necessary, the following items:
Operation and fit of windows
Pedal height and free play of clutch pedal
Parking brake
Under hood—engine running at operating temperature
INSPECT the following items:
Automatic transaxle fluid level
Operation of idle-up system for electrical load, air conditioner or power steering (if equipped)
Ignition timing
Idle speed
GENERAL INFORMATION
00–00–28
On hoist
INSPECT the following items:
Manual transaxle oil level
Underside fuel, coolant and hydraulic lines, fittings, connections, and components for leaks
Tires for cuts or bruises
Steering linkage, suspension, exhaust system, and all underside hardware for looseness or damage
Road test
INSPECT the following items:
Brake operation
Clutch operation
Steering control
Operation of gauges
Squeaks, rattles, and unusual noises
Engine general performance
Emergency locking retractors and automatic locking retractors
Cruise control system (if equipped)
After road test
INSPECT for necessary owner information materials, tools, and spare tire in vehicle
The following items must be done just before delivery to your customer.
Load test battery and charge if necessary (Load test result: Volts)
Adjust tire pressure to specification (Specified tire pressure is indicated on the door label.)
Clean outside of vehicle
Install fuses for accessories
Remove seat and cabin carpet protective covers
Vacuum inside of vehicle
End Of Sie
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст