Mazda Protege 5. Manual — part 253
AUTOMATIC TRANSAXLE
05–17–21
05–17
5. Remove the clip and disconnect the selector
cable.
Caution
••••
Do not use an impact wrench. Hold the
manual shaft lever when removing the
manual shaft nut, or the transaxle may be
damaged.
6. Set the adjustable wrench as shown to hold the
manual shaft lever.
7. Remove the manual shaft nut and washer.
8. Remove the manual shaft lever.
9. Remove the TR switch.
10. Rotate the manual shaft to the converter housing
side fully, then return 2 notches to set the N
position.
11. Align the protrusion and mark as shown.
X3U517WAC
Y3U517WAM
X3U517WAD
X3U517WAE
X3U517WCW
1712-1U-01G(05-17).fm 21 ページ 2001年6月29日 金曜日 午前10時12分
AUTOMATIC TRANSAXLE
05–17–22
12. Install the TR switch while aligning the protrusion
and groove as shown.
13. Turn the TR switch so that the neutral hole is in
line with the flat, straight surfaces on either side of
the manual shaft.
14. Hand-tighten the TR switch bolts.
15. Perform the TR switch adjustment. (See 05–17–
23 TRANSAXLE RANGE (TR) SWITCH
ADJUSTMENT.)
16. Install the manual shaft lever and washer.
Caution
••••
Do not use an impact wrench. Hold the
manual shaft lever when tightening the
manual shaft nut, or the transaxle may be
damaged.
17. Set the adjustable wrench as shown to hold the manual shaft lever.
18. Tighten the manual shaft nut using a torque
wrench.
Tightening torque
32—46 N·m {3.2—4.7 kgf·m, 24—33 ft·lbf}
19. Install the clip as shown in the figure.
X3U517WCX
X3U517WAF
X3U517WAJ
X3U517WCZ
1712-1U-01G(05-17).fm 22 ページ 2001年6月29日 金曜日 午前10時12分
AUTOMATIC TRANSAXLE
05–17–23
05–17
20. Verify that the selector lever range position and
TR switch are aligned, then connect the selector
cable.
21. Inspect for continuity at the TR switch. (See 05–
17–20 Inspection of Continuity.)
22. Connect the TR switch connector.
23. Install the splash shield.
24. Install the air cleaner component and fresh-air
duct. (See 01–13A–5 INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [ZM].) (See 01–13B–
6 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION [FS].)
25. Connect the negative battery cable.
26. Inspect operation of the TR switch. (See 05–17–
20 Inspection of Operation.)
End Of Sie
TRANSAXLE RANGE (TR) SWITCH ADJUSTMENT
A3U051719440W03
1. Disconnect the negative battery cable.
2. Remove the fresh-air duct and air cleaner component. (See 01–13A–5 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION [ZM].) (See 01–13B–6 INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [FS].)
3. Remove the splash shield.
4. Remove the clip and disconnect the selector
cable.
5. Rotate the manual shaft to the converter housing
side fully, then return 2 notches to set the N
position.
6. Disconnect the TR switch connector.
X3U517WAK
X3U517WD0
X3U517WD3
X3U517WAL
1712-1U-01G(05-17).fm 23 ページ 2001年6月29日 金曜日 午前10時12分
AUTOMATIC TRANSAXLE
05–17–24
7. Loosen the TR switch mounting bolts.
8. Connect an ohmmeter between terminals B and
H.
9. Adjust the switch to the point where there is
continuity between the terminals.
10. Tighten the TR switch mounting bolts.
Tightening torque
7.9—10.7 N·m {80—110 kgf·cm, 69.5—95.4
in·lbf}
11. Verify that the selector lever range position and
TR switch are aligned.
12. Connect the TR switch connector.
13. Install the clip as shown in the figure.
14. Connect the selector cable.
15. Install the splash shield.
16. Install the air cleaner component and fresh-air
duct. (See 01–13A–5 INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [ZM].) (See 01–13B–
6 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION [FS].)
17. Connect the negative battery cable.
End Of Sie
X3U517WAM
Z3U517W15
X3U517WD1
X3U517WD2
1712-1U-01G(05-17).fm 24 ページ 2001年6月29日 金曜日 午前10時12分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст