Mazda Protege 5. Manual — part 265
ENGINE SPEED SENSING POWER STEERING
06–12–9
06–12
STEERING LOCK (ATX MODEL) INSPECTION
A3U061275990W01
1. Verify that the cable connector does not move
when the key is in the LOCK position and that it
moves freely with the key in other positions.
•
Replace the steering lock component as
necessary.
End Of Sie
STEERING GEAR AND LINKAGE REMOVAL/INSTALLATION
A3U061232960W01
Caution
••••
Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while servicing the vehicle.
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. After installation, inspect the toe-in. (See 02–11–1 FRONT WHEEL ALIGNMENT.)
.
X3U612WAD
A3U0612W012
1
Bolt (intermediate shaft)
(See 06–12–10 Bolt (Intermediate Shaft) Removal
Note)
(See 06–12–10 Bolt (Intermediate Shaft) Installation
Note)
2
Cotter pin
3
Nut
4
Tie-rod end ball joint
(See 06–12–10 Tie-rod End Ball Joint Removal
Note)
5
Transverse member (ZM (ATX), FS)
6
Engine mount member
(See 06–12–10 Engine Mount Member Removal
Note)
7
Pressure pipe
8
Return pipe and clamp
9
Oil pipe
10
Steering gear and linkage
(See 06–12–10 Steering Gear and Linkage
Removal Note)
1712-1U-01G(06-12).fm 9 ページ 2001年6月29日 金曜日 午前10時17分
ENGINE SPEED SENSING POWER STEERING
06–12–10
Tie-rod End Ball Joint Removal Note
1. Remove the tie rod nut.
2. Separate the tie-rod end from the steering
knuckle using the SSTs.
Engine Mount Member Removal Note
1. Set the SSTs as shown in the figure.
2. Remove the engine mount member.
Bolt (Intermediate Shaft) Removal Note
1. Mark the pinion shaft and gear housing for proper
installation.
Steering Gear and Linkage Removal Note
1. Remove the steering gear and linkage by pulling it from the right side.
Bolt (Intermediate Shaft) Installation Note
1. Align the marks and install the intermediate shaft and bolt.
End Of Sie
X3U612WAF
Z3U0612W004
Y3U612WA8
1712-1U-01G(06-12).fm 10 ページ 2001年6月29日 金曜日 午前10時17分
ENGINE SPEED SENSING POWER STEERING
06–12–11
06–12
STEERING GEAR AND LINKAGE DISASSEMBLY
A3U061232960W02
1. Disassemble in the order indicated in the table.
.
Z3U0612W013
1
Oil pipe
2
Tie-rod end
3
Locknut (Tie-rod end)
4
Boot band
5
Boot wire
6
Boot
7
Tie rod
(See 06–12–12 Tie Rod Disassembly Note)
8
Washer
9
Locknut (Adjusting cover)
(See 06–12–12 Locknut (Adjusting Cover)
Disassembly Note)
10
Adjusting cover
11
Yoke spring
12
Support yoke
13
O-ring
14
Dust cover
15
Socket bolt
16
Pinion shaft and housing component
(See 06–12–12 Pinion Shaft and Housing
Component Disassembly Note)
17
Pinion shaft component
(See 06–12–13 Pinion Shaft Component
Disassembly Note)
18
Snap ring
(See 06–12–13 Snap Ring Disassembly Note)
19
Control valve component
20
Seal ring
21
Pinion shaft
22
Valve housing component
23
Upper bearing
(See 06–12–13 Upper Bearing Disassembly Note)
24
Oil seal
25
Valve housing
26
Holder
(See 06–12–13 Holder Disassembly Note)
27
U-gasket
28
O-ring
29
Steering rack
30
Seal ring
31
O-ring
32
Inner guide
(See 06–12–14 Inner Guide Disassembly Note)
33
Oil seal
34
Mounting bracket
35
Mount
36
Mounting rubber
(See 06–12–14 Mounting Rubber Disassembly
Note)
37
Gear housing
38
Tie-rod end boot
(See 06–12–15 Tie-rod End Boot Disassembly
Note)
1712-1U-01G(06-12).fm 11 ページ 2001年6月29日 金曜日 午前10時17分
ENGINE SPEED SENSING POWER STEERING
06–12–12
Tie Rod Disassembly Note
1. Unclamp the washer.
2. Remove the tie-rod.
Locknut (Adjusting Cover) Disassembly Note
1. Remove the locknut using the SST.
Pinion Shaft and Housing Component Disassembly Note
1. Remove the socket bolts (2 points) which fix the
pinion shaft and housing.
2. Hold the pinion shaft as shown, and pull the
pinion shaft out and housing component.
X3U612WAK
A3U0612W009
X3U612WAM
X3U612WAN
1712-1U-01G(06-12).fm 12 ページ 2001年6月29日 金曜日 午前10時17分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст