Mazda Protege 5. Manual — part 264
ENGINE SPEED SENSING POWER STEERING
06–12–5
06–12
8. Remove the SSTs. Install and tighten the
pressure pipe to the specified torque.
Tightening torque
30—44 N·m {3.0—4.5 kgf·m, 22—32 ft·lbf}
9. Bleed the air from the system.
End Of Sie
STEERING WHEEL AND COLUMN INSPECTION
A3U061232010W01
Steering Wheel Play Inspection
1. With the wheels in the straight-ahead position, gently turn the steering wheel to the left and right and verify that
the play is within the specification.
•
If the play exceeds the specification, either the steering joints are worn or the backlash of the steering gear
is excessive. Correct as necessary.
Play
0—30 mm {0—1.18 in}
Steering Wheel Looseness Inspection
1. Move the steering wheel as shown in the figure to
inspect for column bearing wear, steering shaft
joint play, steering wheel looseness, and column
looseness.
•
Repair or replace as necessary.
Steering Wheel Effort Inspection
1. Inspect the following points:
•
Tire size and tire pressure
•
Fluid level
•
Drive belt deflection
2. With the vehicle on a hard, level surface, put the wheels in the straight-ahead position.
Warning
••••
See 08-10 DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION for removal/installation of
the air bag module after inspection.
3. Remove the air bag module.
4. Start the engine and warm the power steering fluid to 50—60
°°°°
C {123—140
°°°°
F}.
5. Measure the steering wheel effort using a torque
wrench.
•
If not within the specification, note the
following:
— Air in system
— Fluid leakage at hose or connectors
— Function of oil pump and steering gear
Steering wheel effort
7.8 N·m {80 kgf·cm, 69 in·lbf} max.
Note
•
To determine whether the steering effort is
satisfactory or not, perform the inspection on
another vehicle of the same model and under the same conditions, and compare the results.
A3U0612W004
A3U0612W017
A3U0612W018
1712-1U-01G(06-12).fm 5 ページ 2001年6月29日 金曜日 午前10時17分
ENGINE SPEED SENSING POWER STEERING
06–12–6
•
The steering wheel effort varies with conditions as shown below.
— Road conditions, such as dry or wet, and asphalt or concrete.
— Tire conditions, such as brand, wear, and tire pressure.
End Of Sie
STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION
A3U061232010W02
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
.
A3U0612W016
1
Air bag module
(See 08–10–5 DRIVER-SIDE AIR BAG MODULE
REMOVAL/INSTALLATION)
2
Locknut
3
Steering wheel
(See 06–12–7 Steering Wheel Removal Note)
(See 06–12–8 Steering Wheel Installation Note)
4
Column cover
5
Clock spring
(See 08–10–9 CLOCK SPRING REMOVAL/
INSTALLATION)
6
Combination switch
7
Lower panel
8
Key interlock cable
9
Steering shaft
(See 06–12–8 Steering Shaft Installation Note)
10
Shaft seal
11
Set plate
12
Dust cover
13
Universal joint
14
Steering lock mounting bolts and bracket
(See 06–12–7 Steering Lock Mounting Bolts and
Bracket Removal Note)
(See 06–12–7 Steering Lock Mounting Bolts and
Bracket Installation Note)
15
Steering lock component
16
Cylinder outer component
(See 06–12–7 Cylinder Outer Component Removal
Note)
1712-1U-01G(06-12).fm 6 ページ 2001年6月29日 金曜日 午前10時17分
ENGINE SPEED SENSING POWER STEERING
06–12–7
06–12
Steering Wheel Removal Note
1. Set the vehicle in the straight-ahead position.
2. Remove the steering wheel using a suitable puller.
Caution
••••
Do not try to remove the steering wheel by hitting the shaft with a hammer. The column will
collapse.
Steering Lock Mounting Bolts and Bracket Removal Note
1. Make a groove in the heads of the steering lock
mounting bolts using a chisel and a hammer.
2. Remove the bolts using a screwdriver.
3. Disassemble the steering lock component.
Cylinder Outer Component Removal Note
Caution
••••
When replacing the cylinder outer component, the coil also must be replaced.
1. Set the key in the ACC position.
2. Keep pushing the button and remove the cylinder
outer component.
Steering Lock Mounting Bolts and Bracket Installation Note
1. Assemble the steering lock component to the steering shaft.
2. Verify that the lock operates correctly.
3. Install new steering lock mounting bolts.
4. Tighten the bolts until the heads break off.
X3U612WA7
X3U612WA8
X3U612WA9
1712-1U-01G(06-12).fm 7 ページ 2001年6月29日 金曜日 午前10時17分
ENGINE SPEED SENSING POWER STEERING
06–12–8
Steering Shaft Installation Note
Caution
••••
Do not apply a shock in the axial direction of the shaft.
1. Tighten bolt A.
2. Tighten bolt C.
3. Tighten bolt B.
4. Release the adjusting lever, and lower the
steering shaft to the lowest position.
5. Tighten bolt D.
Steering Wheel Installation Note
1. Set the wheels in the straight-ahead position, and install the steering wheel.
End Of Sie
STEERING SHAFT INSPECTION
A3U061232100W01
1. Inspect the following.
(1) Column bearing for damage
(2) Steering shaft length
•
Replace the steering shaft component as
necessary.
Length
797.4—800.4 mm {31.40—31.51 in}
2. Tilt operation
(1) Verify that the adjusting lever moves smoothly
from unlock position to lock position.
(2) Verify that the steering shaft is fixed firmly
when the adjusting lever is locked.
•
Replace the steering shaft component as
necessary.
End Of Sie
Y3U612WA3
Y3U612WA4
X3U612WAC
1712-1U-01G(06-12).fm 8 ページ 2001年6月29日 金曜日 午前10時17分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст