Mazda MX-5 Miata / Grand Touring. Manual — part 23
FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION
1. Remove the mudguard.
2. Remove in the order indicated in the table.
M
RF wheel-
speed sensor
(signal)
RF ABS
wheel-speed
sensor
Continuity
M-RF ABS
wheel-speed
sensor
connector
terminal A
Continuity
detected
harness (M-
RF ABS
wheel-speed
sensor
connector
terminal A)
N
Brake switch Brake switch
Voltage
N-brake switch
(Brake pedal
depressed)
B+
Wiring
harness (N-
brake
switch)
Brake
switch
Y-brake switch
(Brake pedal
not depressed)
1 V or less
O
RF wheel-
speed sensor
(ground)
RF ABS
wheel-speed
sensor
Continuity
O-RF ABS
wheel-speed
sensor
connector
terminal B
Continuity
detected
Wiring
harness (O-
RF ABS
wheel-speed
sensor
connector
terminal B)
P
-
-
-
-
-
-
Q
-
-
-
-
-
-
R
-
-
-
-
-
-
S
-
-
-
-
-
-
T
-
-
-
-
-
-
U
-
-
-
-
-
-
V
-
-
-
-
-
-
W
-
-
-
-
-
-
X
-
-
-
-
-
-
Y
CAN_L
DLC-2
(CAN_L)
Continuity
Y-DLC-2
terminal
CAN_L.
Continuity
detected
Wiring
harness (Y-
DLC-2
terminal
CAN_L)
Z
CAN_H
DLC-2
(CAN_H)
Continuity
Z-DLC-2
terminal
CAN_H
Continuity
detected
Wiring
harness (Z-
DLC-2
terminal
CAN_H)
2008 Mazda MX-5 Miata Grand Touring
2008 BRAKES Antilock Brake System - MX-5 Miata
3. Install in the reverse order of removal.
Fig. 11: Identifying Front ABS Wheel-Speed Sensor (With Torque Specifications)
Courtesy of MAZDA MOTORS CORP.
FRONT ABS WHEEL-SPEED SENSOR INSPECTION
INSTALLATION VISUAL INSPECTION
1. Inspect the following items:
If there is any malfunction, replace the applicable part.
1. Excessive play of the ABS wheel-speed sensor
2. Deformation of the ABS wheel-speed sensor
CLEARANCE INSPECTION
1. Remove the front ABS wheel-speed sensor.
2. Measure the distance between the front ABS wheel-speed sensor installation surface and the ABS sensor
rotor. This is dimension A.
3. Measure the distance between the front ABS wheel-speed sensor installation surface and the tip of ABS
wheel-speed sensor. This is dimension B.
2008 Mazda MX-5 Miata Grand Touring
2008 BRAKES Antilock Brake System - MX-5 Miata
4. Calculate the clearance between the front ABS wheel-speed sensor and the ABS sensor rotor using the
following formula:
Clearance (mm {in}) = A - B
5. Verify that the clearance between the ABS sensor rotor and the front ABS wheel-speed sensor is as
indicated below.
If there is any malfunction, replace it.
Clearance
0.3-1.0 mm {0.012-0.057 in}
Fig. 12: Measuring Distance Between Front ABS Wheel-Speed Sensor Installation Surface & ABS
Wheel-Speed Sensor Tip
Courtesy of MAZDA MOTORS CORP.
2008 Mazda MX-5 Miata Grand Touring
2008 BRAKES Antilock Brake System - MX-5 Miata
SENSOR OUTPUT VALUE INSPECTION
1. Turn the ignition switch off.
2. Connect the M-MDS or equivalent to the DLC-2.
Fig. 13: Locating DLC-2 Connector
Courtesy of MAZDA MOTORS CORP.
3. Select the following PIDs using the M-MDS or equivalent:
LF_WSPD
(LF wheel-speed sensor)
RF_WSPD
(RF wheel-speed sensor)
4. Start the engine and drive the vehicle.
5. Verify that the display of the M-MDS or equivalent shows the same value as the speedometer.
CAUTION:
Resistance inspection using other testers may cause damage to the
ABS wheel-speed sensor internal circuit. Be sure to use the M-MDS
or equivalent to inspect the ABS wheel-speed sensor.
2008 Mazda MX-5 Miata Grand Touring
2008 BRAKES Antilock Brake System - MX-5 Miata
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст