Mazda 5. Manual — part 67

BODY STRUCTURE [PANEL REPLACEMENT]

09–80B–31

09

3. Remove the front pillar (outer).

4. Rough cut area (D) and drill the 5 locations indicated by (E).
5. Drill the 6 locations indicated by (F) from the interior.
6. Remove the bolt from the locations indicated by (A).
7. Remove the front pillar reinforcement.

Note

• When removing the front pillar reinforcement (upper) and the front pillar reinforcement (rear) separately,

drill the 10 locations indicated by (H).

(B)12

(C)2

90mm

55mm

{2.17in}

{3.54in}

(B)25

(B)27

(B)2

(B)2

(B)3

430mm

{16.93in}

50mm {1.97in}

INSULATOR

INSULATOR

(A)

(A)

A

A

A-A

B-B

B

B

CUT-AND-JOIN LOCATION
FOR FRONT PILLAR
(OUTER)

CUT-AND-JOIN LOCATION
FOR FRONT PILLAR
(OUTER)

ROUGH CUT LOCATION FOR
FRONT PILLAR (OUTER)

ROUGH CUT LOCATION FOR
FRONT PILLAR (OUTER)

DPE0980B077

09–80B–32

BODY STRUCTURE [PANEL REPLACEMENT]

8. Rough cut area (I) and remove the side sill reinforcement (front).

(E)1

(H)10

(E)4

35mm

{1.38in}

45mm

{1.77in}

(D)

(I)

(F)3

(G)1

80mm {3.15in}

{1.57in}

40mm

(

CUT-AND-JOIN LOCATION FOR FRONT
PILLAR REINFORCEMENT (UPPER)

FRONT PILLAR REINFORCEMENT
(UPPER)

ROUGH CUT LOCATION FOR
FRONT PILLAR REINFORCEMENT
(UPPER)

FRONT PILLAR REINFORCEMENT
(LOWER)

SIDE SILL
REINFORCEMENT (FRONT)

CUT-AND-JOIN LOCATION FOR SIDE
SILL REINFORCEMENT (FRONT)

ROUGH CUT LOCATION FOR SIDE
SILL REINFORCEMENT (FRONT)

DPE0980B078

BODY STRUCTURE [PANEL REPLACEMENT]

09–80B–33

09

9. Rough cut area (J), drill the location indicated by (K), and then remove the front pillar (inner).

End Of Sie

FRONT PILLAR INSTALLATION

DPE098074090B02

1. When joining and cutting the new and existing parts, trial fit the new part in position, and then measure and

adjust the body as necessary to conform with standard dimensions.

2. Drill holes for plug welds before installing new parts.

Note

• The shape for the right side is different. In areas where the outer, reinforcement, inner, and other parts are

in 3-4 layers, drill holes for plug welds in all but the innermost panel.

(K)1

(J)

50mm

{1.97in}

110mm

{4.33in}

FRONT PILLAR (INNER)

CUT-AND-JOIN LOCATION FOR
FRONT PILLAR (INNER)

ROUGH CUT LOCATION FOR
FRONT PILLAR (INNER)

DPE0980B079

09–80B–34

BODY STRUCTURE [PANEL REPLACEMENT]

3. Make a reinforcement panel using the material from the front pillar reinforcement.
4. To cut and join the new and existing parts, cut the new part at the specified location shown in the figure, and

chamfer the joint surfaces of the new and existing parts.

5. Because the front pillar reinforcement cannot be welded to the existing parts from the inside of the inner, drill 4

plug weld holes at the locations indicated by (A) on the existing parts. Install the reinforcement and the existing
parts by plug welding from the outside, then butt weld the new and existing parts.

Caution

• Press fit the reinforcement panel and the body side material, and then plug weld them.

6. Grind the butt welded area with a disc grinder to finish the surface.
7. Install the bolt to the locations indicated by (B).
8. Weld the 9 locations indicated by (C) and install the front pillar reinforcement.

1

110mm

{4.33in}

CUT-AND-JOIN LOCATION FOR
FRONT PILLAR (INNER)

FRONT PILLAR (INNER)

DPE0980B082