Loader Bobcat 773. Manual — part 118
C
P–17333
1
1
3
2
A
P–16578
1
B
P–13732
P–13725
1
1
–10–36–
Service Manual
773 BICS Loader
CONTROL HANDLE
(ADVANCED HAND CONTROL)
(AHC) W/PUSH BUTTON FLOAT (Cont’d)
Handle Sensor Connector
The wire connector (Item 1) [A] can be removed from the
handle sensor wires, use the following procedure.
Remove the wedge (Item 1) [B] from the connector.
With a pointed tool, lift the tab (Item 1) [C] and pull the wire
from the connector.
Assembly: Install the wires into the connector as listed
below [C]:
1–Terminal – Red
2–Terminal – Black
3–Terminal – Green
Revised June 01
A
N–22794
1
B
P–13732
P–13725
1
1
Service Manual
–10–37–
773 BICS Loader
CONTROL HANDLE
(ADVANCED HAND CONTROL)
(AHC) W/PUSH BUTTON FLOAT (Cont’d)
Switch Handle Removal And Installation
To remove the switch handle, the connector (Item 1) [A]
must be removed from the wires.
Remove the wedge (Item 1) [B] from the connector.
Using a pointed tool, press down on the tab (Item 1) [C] and
pull the wire from the connector.
Installation: Install the wires into the connector as listed
below [C]:
Right Control Lever Switch Handle
1–Terminal – Red/White
2–Terminal – Black/White
3–Terminal – Purple/White
Left Control Lever Switch Handle
1–Terminal – Red/White
2–Terminal – Black/White
3–Terminal – Purple/White
Revised June 01
C
P–17335
1
3
2
1
A
N–17779
1
2
–10–38–
Service Manual
773 BICS Loader
CONTROL HANDLE
(ADVANCED HAND CONTROL)
(AHC) W/PUSH BUTTON FLOAT (Cont’d)
Switch Handle Removal And Installation (Cont’d)
Disconnect the right switch handle connectors (Items 1 &
2) [A] from the loader wiring harness connectors.
Disconnect the left switch handle connectors (Items 1, 2,
3 & 4) [B] from loader wiring harness connectors.
Remove the connector locks and connectors from the
wires to remove the switch handle from the control handle.
Installation:The wire colors of the control lever harness
are as follows:
Right Switch Handle
Ten–Pin Connecter
A–Terminal – Orange
B–Terminal – White
C–Terminal – White/Black
D–Terminal – White/Red
E–Terminal – Dk. Green
F–Terminal – White/Lt. Green
G–Terminal – Blank
H–Terminal – Lt. Green
J–Terminal – Yellow
K–Terminal – Blank
Three–Pin Connector
A–Terminal – Pink/Red
B–Terminal – Pink/Black
C–Terminal – Pink/Lt. Green
Left Switch Handle
Ten–Pin Connector
A–Terminal – Orange
B–Terminal – Dk. Blue
C–Terminal – White
D–Terminal – Purple
E–Terminal – Blank
F–Terminal – Tan
G–Terminal – Pink
H–Terminal – Blank
J–Terminal – Blank
K–Terminal – Blank
Three–Pin Connector
A–Terminal – Red/White
B–Terminal – Black/White
C–Terminal – Purple/White
Two–Pin Connector
A–Terminal – Black
B–Terminal – Red
Five–Pin Connector
A–Terminal – Dk. Green
B–Terminal – Brown
C–Terminal – Blank
D–Terminal – Yellow
E–Terminal – Blank
Revised June 01
B
N–17772
1
3
2
4
C
N–22794
1
A
N–22783
1
2
2
Service Manual
–10–39–
773 BICS Loader
CONTROL HANDLE
(ADVANCED HAND CONTROL)
(AHC) W/PUSH BUTTON FLOAT (Cont’d)
Switch Handle Removal And Installation (Cont’d)
Roll the pistol grip handle cover (Item 1) [A] down.
Using a small screwdriver, lift the handle tabs (Item 2) [A]
and slightly rotate the switch handle.
Pull the switch handle and wiring harness assembly (Item
1) [B] from the control lever.
Installation: When installing the switch handle and wiring
harness assembly into the control handle, route the
harness (Item 1) [C] to assure proper return of the control
handle to neutral position.
Revised June 01
B
N–22784
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст