Acura RL (1996-2004 year). Manual — part 701
Check the SRS indicator light circuit:
1. Turn the ignition switch OFF.
2. Remove the gauge assembly. Do not disconnect the con-
nector from the gauge assembly.
3. Connect the No. 15 terminal of the dashboard wire har-
ness 30P connector and No. 22 terminal of the dashboard
wire harness 22P connector with a jumper wire (see page
).
4. Turn the ignition switch ON (II).
Faulty SRS unit or poor contact at the SRS main harness
18P connector; check the connector. If the connector is
OK, replace the SRS unit (see page
).
Check for a short to ground in the SRS indicator light cir-
cuit:
1. Turn the ignition switch OFF.
2. Disconnect the dashboard wire harness 30P connector
from the gauge assembly (see page
).
3. Check resistance between the No. 15 terminal of the
dashboard wire harness 30P connector and body ground.
There should be 1 or more.
Check for an open in the SRS indicator light circuit:
1. Turn the ignition switch OFF.
2. Disconnect the dashboard wire harness 30P connector
from the gauge assembly (see page
).
3. Check resistance between the No. 4 terminal of the SRS
main harness 18P connector and No. 15 terminal of the
dashboard wire harness 30P connector, there should be
(D)
(F)
(cont'd)
Main Menu
Table of Contents
Troubleshooting - '99 - 01 Models
The SRS Indicator Light Doesn't Go Off (cont'd)
(D) From page
(F)
Check for an open in the dashboard wire harness:
1. Disconnect the main wire harness 8P connector from the
dashboard wire harness (see page
).
2. Check resistance between the No. 4 terminal of the SRS
main harness 18P connector and No. 6 terminal of the
main wire harness 6P connector; there should be
Check for a short to ground in the main wire harness:
1. Disconnect the main wire harness 8P connector from the
dashboard wire harness (see page
2. Check resistance between the No. 6 terminal of the main
wire harness 8P connector and body ground. There
should be 1 or more.
Check for a short to ground in the SRS main harness:
1. Disconnect the SRS main harness 8P connector from the
2. Check resistance between the No. 6 terminal of the SRS
main harness 8P connector and body ground. There
should be 1 or more.
(G)
Main Menu
Table of Contents
From page
(G) (E) From page
Check for an open in the main wire harness:
1. Disconnect the SRS main harness 8P connector from the
).
2. Check resistance between the No. 4 terminal of the SRS
main harness 18P connector and No. 6 terminal of the
SRS main harness 8P connector; there should be 0 - 1.0
The problem has disappeared due to disconnecting and
connecting the connectors. Be sure all terminals make
good contact, and recheck the system (see Trouble-
shooting Intermittent Failures on page
).
Main Menu
Table of Contents
Troubleshooting - '99 - 01 Models
DTC 1-1 and DTC 1-2
CAUTION: Whenever the ignition switch is ON (II), or has
been turned OFF for less than 3 minutes, be careful not
to bump the SRS unit or the side impact sensor; the
airbags could accidentally deploy and cause damage or
injuries.
Try to reproduce the SRS indicator light:
1. Erase the DTC memory (see page
).
2. Turn the ignition switch ON (II), and check that the SRS
indicator light comes on for about 6 seconds, and then
goes off.
Check for an open or increased resistance in the SRS main
harness:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the front passenger's airbag connector (see
page
).
3. Disconnect the SRS main harness 18P connector from the
). Do not disconnect the special
tool from the SRS main harness 2P connector.
4. Check resistance between the No. 9 terminal and the No.
18 terminal of the SRS main harness 18P connector. There
should be 2.0-3.0
Intermittent failure, system is OK at this time. See
Troubleshooting Intermittent Failures on page
Check for an open or increased resistance in the driver's
airbag inflator:
1. Disconnect the negative battery cable, and wait for 3
minutes.
2. Disconnect the driver's airbag 2P connector from the
cable reel 2P connector (see page
).
3. Connect the special tool to the cable reel 2P connec-
).
4. Reconnect the negative battery cable.
5. Erase the DTC memory (see page
).
).
Open or increased resistance in the driver's airbag inflator;
replace the driver's airbag (see page
).
Check for an open or in increased resistance in the cable reel:
1. Disconnect the SRS main harness 2P connector from the
cable reel 2P connector (see page
).
2. Connect the special tool to the SRS main harness
).
3. Erase the DTC memory (see page
).
).
Open or increased resistance in the cable reel; replace the
cable reel (see page
).
Faulty SRS unit or poor contact at the SRS main harness
18P connector and the SRS unit, check the connection
between the SRS main harness 18P connector and the SRS
unit.
• If the connection is OK, replace the SRS unit (see page
).
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст