Acura RL (1996-2004 year). Manual — part 585
6 x 1.0 mm
9.8 N-m
(1.0 kgf-m,
7.2 Ibf-ft)
OPENER COVER
Slide and remove the
opener cover while
pulling it up.
HOOK
FUEL FILL DOOR
OPENER
HOOK
To fuel fill door
latch.
KNOB
FUEL FILL DOOR
OPENER CABLE
(see page
Installation is the reverse of the removal procedure.
NOTE:
Make sure the opener cable is connected properly.
Make sure the fuel fill door opens properly.
Fuel fill door latch:
NOTE: Remove the following parts.
Rear edge of the trunk side trim (left side, see page
: Bolt locations, 2
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
FUEL FILL DOOR
After installing check for
a flush fit with the body.
FUEL FILL DOOR OPENER
CABLE
(see page
FUEL FILL DOOR LATCH
Remove the fuel fill door latch
by turning it 90°
Installation is the reverse of the removal procedure.
NOTE:
Make sure each opener cable is connected prop-
erly.
Make sure the fuel fill door opens properly and
locks securely.
Fuel fill door opener:
Bolt, screw locations
FUEL FILL DOOR LATCH
Main Menu
Table of Contents
Opener and Latch
Removal (cont'd)
Trunk lid latch/Lock cylinder:
NOTE: Remove the trunk lid trim (see page
).
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
LOCK CYLINDER
SWITCH CONNECTOR
LOCK
CYLINDER
TRUNK LID
LATCH
CONNECTOR
Installation is the reverse of the removal procedure.
NOTE:
Grease the trunk latch.
Make sure the trunk lid opens properly and locks
securely.
Make sure the connector is connected properly.
Bolt locations
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
CYLINDER
ROD
Main Menu
Table of Contents
Windshield Wiper Arms/Windshield Wiper Linkage
Removal
CAUTION: Put on gloves to protect your hands.
NOTE: Take care not to scratch the hood and body.
1. Remove the windshield wiper arms, then remove
the hood seal and cowl cover.
INNER CLIP
NOTCH
(Cowl cover side)
NUTS
10 x 1.25 mm
18 N-m (1.8 kgf-m,
13 Ibf-ft)
WINDSHIELD
WIPER ARMS
COWL
COVER
2. Remove the strut brace (see
).
3. Remove the control box cover, then remove the dash-
board upper center reinforcement.
DASHBOARD
UPPER CENTER
REINFORCEMENT
STRUT BRACE
BRACKET
6 x 1.0 mm
9.8 N-m (1.0 kgf-m ,
7.2 Ibf-ft )
STRUT BRACE
BRACKET
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
4. Disconnect the connector, detach the harness clip,
then remove the windshield wiper linkage assembly.
WINDSHIELD
WIPER LINKAGE
ASSEMBLY
: Bolt locations, 3
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
PIN
(Body side)
HARNESS
CLIP
5. Separate the windshield wiper linkage and wind-
shield wiper motor.
NOTE: When installing, align the alignment marks
on the link and windshield wiper linkage.
6 x 1.0 mm
8 N-m (0.8 kgf-m,
5.8 Ibf-ft)
ALIGNMENT
MARKS
LINK
LINK
WINDSHIELD
WIPER LINKAGE
WINDSHIELD WINDSHIELD
WIPER LINKAGE WIPER MOTOR
6. Installation is the reverse of the removal procedure.
NOTE:
Make sure the connector is connected properly.
If necessary, replace any damaged clips.
Install the windshield wiper arms properly as
Check the windshield wiper motor operation.
Grease the moving parts.
SHOP
TOWEL
Clip locations
CONNECTOR
Bolt locations, 3
NUT
10 x 1.25 mm
18 N-m (1.8 kgf-m,
13 Ibf-ft)
SPRING
WASHER
Main Menu
Table of Contents
Washer Reservoir
Removal
CAUTION: Put on gloves to protect your hands.
'96 - 99 models:
1. Remove the bolt, then pull out the washer filler.
Bolt location, 1
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
WASHER
RESERVOIR
WASHER
FILLER
'00-01 models:
1. Remove the bolt, then pull out the washer filler.
: Bolt location, 1
HOOK
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
WASHER
FILLER
2. Pull away the inner fender as necessary (see page
).
3. Disconnect the washer tube and washer motor con-
nector.
: Bolt locations, 3
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
WASHER
RESERVOIR
CONNECTOR
WASHER
WINDSHIELD TUBE
WASHER MOTOR
4. Remove the bolt, then remove the washer reservoir.
5. Installation is the reverse of the removal procedure.
NOTE:
Make sure the washer motor connector and
washer tube is connected properly.
Check the washer motor operation.
HOOK
HOOK
CONNECTOR
WINDSHIELD
WASHER MOTOR
WASHER
TUBE
WASHER
RESERVOIR
2. Pull away the inner fender as necessary (see page
).
3. Disconnect the washer tube and windshield washer
motor connector.
4. Remove the bolt, then remove the washer reservoir
by sliding it forward.
5. Installation is the reverse of the removal procedure.
NOTE:
Make sure the windshield washer motor connec-
tor and washer tube is connected properly.
Check the windshield washer motor operation.
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст