Acura RL (1996-2004 year). Manual — part 584
Inner Fender, Fenderwell Trim, Rear Fender Cover,
and Rear Air Outlet
Removal
NOTE: If necessary, replace any damaged clips
Inner fender:
: Bolt, screw locations
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
: Clip locations, 11
INNER FENDER
Fenderwell trim/Rear fender cover/Rear air outlet:
NOTE:
Take care not to bend the fenderwell trim.
Before installing the fenderwell trim, clean the body
bonding surface with a sponge dampened in alcohol.
After cleaning, keep oil, grease, or water from getting
on the surface.
To remove the rear fender cover, first remove the rear
wheel (see
To remove the rear fender cover, first pull out the front
edge of the rear bumper (see page
).
To remove the rear air outlet, first remove the rear
).
STEEL
CORE
: Bolt, screw locations
Left, 3
Right, 2
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
HOOKS
: Clip locations
FENDERWELL
TRIM
REAR AIR
OUTLET
Rear bumper
outline
Left side only.
REAR FENDER
COVER
GROMMET
REAR FENDER
COVER
REAR
BUMPER
CLIP
FENDERWELL
TRIM
ADHESIVE
Main Menu
Table of Contents
Opener Cable/Opener and Latch/Wiper and Washer
WINDSHIELD WIPER ARMS
and LINKAGE
Removal, page
WINDSHIELD
WASHER NOZZLES
Adjustment, page
TRUNK LID OPENER
MAIN SWITCH
Test, page
FUEL FILL DOOR OPENER
CABLE
(see page
HOOD OPENER CABLE
(see page
TRUNK LID
OPENER SWITCH
Test, page
FUEL FILL DOOR OPENER
(see page
WASHER RESERVOIR
WASHER RESERVOIR
('96-99 models)
WINDSHIELD
WASHER TUBE
(see page
Component Location Index
Main Menu
Table of Contents
Opener Cables
Removal
NOTE:
When removing the clips, use a clip remover.
Take care not to bend the opener cables.
Hood opener cable:
NOTE: Remove the inner fender (see page
) and kick
) from the left side of the vehicle.
HOOD RELEASE
HANDLE
(see page
: Clip locations
Route the opener
cable through the
holes in the body.
Fuel fill door opener cable:
NOTE: Remove the following parts from the left side of
the vehicle, then pull the carpet and rear carpet back, as
necessary (see page
).
Front and rear side trim (see page
Front and rear door trim (see page
Front seat belt lower anchor (see
Rear seat cushion and rear seat-back (see page
Rear trim panel and trunk side trim (see page
: Clip locations
FUEL FILL DOOR
OPENER
(see page
FUEL FILL DOOR
OPENER CABLE
Installation is the reverse of the removal procedure.
NOTE:
Make sure each opener cable is routed and con-
nected properly.
Make sure the hood and fuel fill door open properly.
HOOD OPENER
CABLE
Main Menu
Table of Contents
Opener and Latch
Removal
NOTE: Take care not to bend the opener cables.
Hood release handle:
NOTE: Remove the dashboard lower cover (see page
).
6 x 1.0 mm
9.8 N-m
(1.0 kgf-m,
7.2 Ibf-ft)
HOOD
RELEASE
HANDLE
Installation is the reverse of the removal procedure.
NOTE:
Make sure the opener cable is connected properly.
Make sure the hood opens properly and locks
securely.
Hood latch:
: Bolt locations, 3
COVER
HOOD OPENER
CABLE
Detach the clip.
HOOD LATCH
SWITCH
CONNECTOR
Installation is the reverse of the removal procedure.
NOTE:
Make sure the opener cable is connected properly.
Make sure the hood opens properly and locks
securely.
Grease each location of the hood latch indicated
by the arrows.
HOOD LATCH
Bolt locations, 2
HOOD LATCH
6 x 1.0 mm
9.8 N-m
(1.0 kgf-m,
7.2 Ibf-ft)
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст