Acura RL (1996-2004 year). Manual — part 325
Engine Removal/Installation
Removal (cont'd)
18. Remove the evaporative emission (EVAP) canister
hose and brake booster vacuum hose.
BRAKE BOOSTER
VACUUM HOSE
EVAP CONTROL
CANISTER HOSE
19. Disconnect the transmission sub-harness connec-
tor, and remove the wire harness clamp.
WIRE HARNESS
CLAMP
TRANSMISSION
SUB-HARNESS
CONNECTOR
CONNECTOR
CONTROL
BOX
21. Disconnect the engine wire harness connectors on
the right side of the engine compartment.
ENGINE WIRE
HARNESS CONNECTOR
20. Disconnect the connector, then remove the control
box.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
Main Menu
Table of Contents
22. Disconnect the spark plug voltage detection module
connector, and remove the engine ground cables.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
GROUND
CABLES
SPARK PLUG VOLTAGE
DETECTION MODULE
CONNECTOR
23. Remove the vacuum hoses.
VACUUM
HOSES
24. Loosen the mounting bolt, lock bolt and adjusting
rod, then remove the alternator belt.
ADJUSTING
ROD
LOCK BOLT
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
ALTERNATOR
BELT
MOUNTING BOLT
10 x 1.25 mm
44 N-m (4.5 kgf-m,
33 Ibf-ft)
25.
Loosen the idler pulley center nut and adjusting
bolt, then remove the air conditioning (A/C) com-
pressor belt.
ADJUSTING
BOLT
IDLER PULLEY
CENTER NUT
10 x 1.25 mm
44 N-m (4.5 kgf-m,
33 Ibf-ft)
A/C COMPRESSOR
BELT
Main Menu
Table of Contents
Engine Removal/Installation
Removal (cont'd)
26. Disconnect the power steering pressure (PSP) switch
connector.
ADJUSTING
BOLT
LOCKNUT
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
PSP SWITCH
CONNECTOR
P/S PUMP
BELT
MOUNTING BOLT
10 x 1.25 mm
44 N-m (4.5 kgf-m,
33 Ibf-ft)
27. Remove the adjusting bolt, locknut and mounting
bolt, then remove the power steering (P/S) pump
belt and pump.
NOTE: Do not disconnect the P/S hoses.
28. Pull the carpet back underneath the front passen-
ger's seat to expose the secondary heated oxygen
sensor (secondary HO2S) connector, then discon-
nect the secondary HO2S connector.
29. Remove the radiator cap.
Use care when removing the radiator
cap to avoid scalding by hot coolant or steam.
30. Raise the hoist to full height.
31. Remove the front tires/wheels and splash shield.
SPLASH
SHIELD
6 x 1.0 mm
9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)
32. Drain the engine coolant (see page
). Loosen
the drain plug in the radiator.
33. Drain the automatic transmission fluid (ATF). Reinstall
the drain plug using a new washer (see
).
34. Drain the differential oil. Reinstall the drain plug
).
35. Drain the engine oil. Reinstall the drain bolt using a
new washer (see page
).
36. Remove the damper forks (see
).
37. Disconnect the suspension lower arm ball joints
).
38. Remove the driveshafts (see
).
NOTE: Coat all precision finished surfaces with
clean engine oil. Tie plastic bags over the driveshaft
ends.
SECONDARY
HO2S CONNECTOR
Main Menu
Table of Contents
39. Disconnect the compressor clutch connector, then
remove the A/C compressor. Do not disconnect the
A/C hoses.
COMPRESSOR CLUTCH
CONNECTOR
A/C COMPRESSOR
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
40. Disconnect the vehicle speed sensor (VSS) connector,
then remove the VSS/power steering speed sensor.
Do not disconnect the fluid hoses.
6 x 1.0 mm
12 N-m (1.2 kgf-m,
8.7 Ibf-ft)
VSS CONNECTOR
VSS/POWER STEERING
SPEED SENSOR
41. Remove the transmission stop collars.
42. Remove exhaust pipe A.
GASKETS
Replace.
GASKET
Replace.
EXHAUST
PIPE A
SELF-LOCKING NUT
10 x 1.25 mm
54 N-m (5.5 kgf-m,
40 Ibf-ft)
Replace.
10 x 1.25 mm
38 N-m (3.9 kgf-m,
28 Ibf-ft)
SELF-LOCKING NUT
10 x 1.25 mm
54 N-m (5.5 kgf-m,
40 Ibf-ft)
Replace.
TRANSMISSION STOP
COLLAR
43. Remove the wire harness cover and grommet, then
remove the three way catalytic converter (TWC).
SELF-LOCKING NUT
10 x 1.25 mm
33 N-m (3.4 kgf-m,
25 Ibf-ft)
Replace.
GROMMET
WIRE HARNESS
COVER
GASKET
Replace.
TWC
6 x 1.0 mm
9.8 N-m (1.0 kgf-m,
7.2 Ibf-ft)
SELF-LOCKING NUT
8 x 1.25 mm
22 N-m (2.2 kgf-m, 16 Ibf-ft)
Replace.
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст