Acura RL (1996-2004 year). Manual — part 454
Oil Seals
Removal
1. Remove the oil seal from the transmission housing.
OIL SEAL
Replace.
TRANSMISSION
HOUSING
2. Remove the oil seal from the torque converter hous-
ing.
OIL SEAL
Replace.
TORQUE CONVERTER
HOUSING
Installation
1. Install the oil seal into the transmission housing
using the special tool as shown.
DRIVER
SEAL DRIVER
ATTACHMENT
10.5-11.5 mm
(0.41 - 0.45 in)
TRANSMISSION
HOUSING
OIL SEAL
2. Install the oil seal into the torque converter housing
using the special tools as shown.
DRIVER
TORQUE CONVERTER
HOUSING
5.7 - 6.7 mm
(0.22 - 0.26 in)
ATTACHMENT,
72 x 75 mm
OIL SEAL
Main Menu
Table of Contents
Torque Converter Housing Bearings
Mainshaft Bearing/Oil Seal Replacement
1. Drive out or pull up the mainshaft bearing and oil seal
using the special tools as shown.
DRIVER
TORQUE CONVERTER HOUSING
ATTACHMENT,
SLIDE HAMMER,
3/8"-16
(Commercially available)
ADJUSTABLE
BEARING PULLER,
25-40 mm
or
2. Drive in the new mainshaft bearing until it bottoms
in the housing using the special tools as shown.
DRIVER
ATTACHMENT,
62 x 68 mm
3. Install the new oil seal flush with the housing using
the special tools as shown.
DRIVER
ATTACHMENT,
72 x 75 mm
Main Menu
Table of Contents
Torque Converter Housing
Bearings
Transmission Housing
Mainshaft Bearing
Countershaft Bearing Replacement
1. Remove the countershaft roller bearing using the
special tool as shown.
SLIDE HAMMER,
3/8" - 16
(Commercially available)
ADJUSTABLE
BEARING
PULLER,
25 - 40 mm
or
2. Install the ATF guide plate.
3. Drive the new bearing into the housing using the
special tools as shown.
DRIVER
ATTACHMENT.
62 x 68 mm
0-0.1 mm
(0-0.003 in)
ATF GUIDE PLATE
Replacement
1. To remove the mainshaft bearing from the trans-
mission housing, expand the snap ring with the
snap ring pliers, then push the bearing out.
NOTE: Do not remove the snap ring unless it's nec-
essary to clean the groove in the housing.
Remove
MAINSHAFT
BEARING
2. Expand the snap ring with the snap ring pliers,
insert the new bearing part-way into it, then release
the pliers. Push the bearing down into the transmis-
sion until the ring snaps in place around it.
NOTE: Install with groove side of the bearing facing
inside the transmission housing.
Install
Main Menu
Table of Contents
Park Mechanism
Disassembly/lnspection/Reassembly
1. Remove the park pawl shaft sleeve, park pawl and park pawl spring.
2. Remove the transmission range switch (see page
).
3. Remove the bolt securing the detent lever to the control shaft, then remove the control shaft.
4. Remove the detent lever and park rod assembly from the transmission housing.
5. Assemble the park mechanism in the reverse order of disassembly.
and
when installing the transmission range switch.
PARK PAWL
SHAFT SLEEVE
PARK PAWL
PARK PAWL
SPRING
PARK PAWL
SHAFT
TRANSMISSION
HOUSING
CONTROL SHAFT
DETENT SPRING PLATE
PARK ROD ASSEMBLY
6 x 1.0 mm
14 N-m
(1.4 kgf-m,
10 Ibf-ft)
PARK ROD
LOCK WASHER
Replace.
DETENT
LEVER
DETENT SPRING PIN
DETENT SPRING
LOCK WASHER
Replace.
6 x 1.0 mm
12 N-m (1.2 kgf-m, 8.7 Ibf-ft)
DETENT LEVER
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст