Acura RL (1996-2004 year). Manual — part 561
Adjustment, page
REAR LOWER
CHANNEL
STRIKER
Adjustment, page
GLASS RUN
CHANNEL
FRONT
CHANNEL
OUTER
HANDLE
COVER
OUTER HANDLE
Removal, page
POWER DOOR
LOCK SWITCH
LATCH
Removal, page
CYLINDER
SWITCH
OUTER HANDLE
BASE
SEAT B
SEAT A
LOCK CYLINDER
INNER HANDLE
CABLE
INNER
HANDLE
TRIM PLATE
LATCH
PROTECTOR
Main Menu
Table of Contents
Doors
Door Panel Removal
NOTE: Take care not to scratch the door panel and other
parts.
1. Remove the trim plate, then remove the screws.
NOTE: Do not remove the inner handle from the
door panel.
Screw locations, 2
Pry here.
INNER
HANDLE
TRIM
PLATE
2. Remove the screw and stop. Release the clips that
hold the door panel, then remove the door panel by
pulling it upward.
NOTE: Remove the door panel with as little bending
as possible to avoid creasing or breaking it.
TRIM PAD
REMOVER
(Commercially
available)
Snap-on
#A177, or
equivalent
12 mm
(0.47 in.)
1 mm
(0.04 in.)
45 mm
(1.77 in.)
Clip locations
DOOR
PANEL
TRIM PAD
REMOVER
DOOR PANEL
STOP
3. Disconnect the connectors and inner handle cable.
SECURITY
INDICATOR
CONNECTOR
(driver's)
POWER SEAT
MEMORY SWITCH
CONNECTOR
(driver's)
COURTESY
LIGHT
CONNECTOR
TWEETER
CONNECTOR
(for some models)
POWER WINDOW
SWITCH CONNECTOR
TRUNK LID
OPENER SWITCH
CONNECTOR
4. Installation is the reverse of the removal procedure.
INNER HANDLE
CABLE
POWER DOOR
LOCK SWITCH
CONNECTOR
TWEETER
CONNECTOR
(for some models)
POWER MIRROR
SWITCH
CONNECTORS
Screw location, 1
95 mm (3.74 in.)
45°
Main Menu
Table of Contents
Outer Handle/Latch Removal
NOTE: Raise the glass fully.
1. Remove:
Door panel
2. Remove the glass run channel as needed, then
remove the rear lower channel.
Bolt location, 1
6 x 1.0 mm
9 N-m (0.9 kgf-m,
7 Ibf-ft)
GLASS RUN
CHANNEL
GLASS RUN
CHANNEL
REAR LOWER
CHANNEL
3. Remove the outer handle cover, then remove the
lock cylinder.
NOTE:
Take care not to drop the bolt inside the door.
Remove in numbered sequence.
Bolt locations
4 x 0.8 mm
3 N-m (0.3 kgf-m,
2 Ibf-ft)
CYLINDER
ROD
Disconnect.
COLLAR
5 x 0.8 mm
5 N-m (0.5 kgf-m,
4 Ibf-ft)
OUTER
HANDLE
BASE
HOLE
SEAL
OUTER
HANDLE
COVER
OUTER
HANDLE
BASE
CLIPS
CYLINDER SWITCH
CONNECTOR
Disconnect and detach.
LOCK
CYLINDER
HOLDER
REAR
LOWER
CHANNEL
Main Menu
Table of Contents
Doors
Outer Handle/Latch Removal (cont'd)
4. Remove the outer handle as shown.
OUTER HANDLE
BASE
LEVER
SEAT B
5. Remove the seat A, then loosen the bolt.
OUTER
HANDLE
BASE
SEAT A
5 x 0.8 mm
5 N-m (0.5 kgf-m,
4 Ibf-ft)
Loosen.
6. Slide the outer handle base, and remove it from the
door. Disconnect the connector, detach the clips,
then remove the latch with the outer handle base
through the hole in the door. Pry the outer handle
rod out from the outer handle base using diagonal
cutters.
NOTE:
To ease reassembly, note location of the outer
handle rod on the joint before disconnecting it.
Take care not to bend the rods.
Screw locations
6 x 1.0 mm
5 N-m (0.5 kgf-m,
4 Ibf-ft)
Nut location, 1
OUTER HANDLE
ROD
DIAGONAL
CUTTERS
6 x 1.0 mm
8 N-m (0.8 kgf-m,
6 Ibf-ft)
CYLINDER
ROD
OUTER
HANDLE
ROD
BUSHING
Replace.
OUTER
HANDLE
BASE
CLIP
LATCH
CLIP
CONNECTOR
7. Installation is the reverse of the removal procedure.
NOTE:
Make sure the glass run channel is installed
securely into the rear lower channel.
Make sure the door locks and opens properly.
SEAT B
OUTER
HANDLE
OUTER
HANDLE
SEAT A
LOCK
ROD
JOINT
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст