Acura RL (2011 year). Manual — part 7
▲ ▼
There are three language selections
you can make: English, French, and
Spanish. To choose the language you
want, follow these instructions:
While METER SETUP is shown in
the CUSTOMIZE GROUP of the
multi-information display, press the
SEL/RESET button. You will see the
above display.
Select the desired language by
pressing the INFO (
/
) button,
then enter your selection by pressing
the SEL/RESET button.
CONTINUED
Language Selection
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
95
10/08/04 18:58:17 31SJA660_100
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
To exit LANGUAGE SELECTION
without changing the current setting,
select EXIT by pressing the INFO
(
/
) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
All messages on the multi-
information display will be shown in
the language you selected.
If your choice is not set, you will see
the above display for several seconds,
then screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
language selection setup.
Multi-Information Display
96
10/08/04 18:58:25 31SJA660_101
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
▲
▼
While the multi-information display
is in the METER SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO (
/
) button until
you see the above display.
Press the SEL/RESET button. The
screen changes as shown above. The
highlighted number is the current
setting above or below the outside
temperature. Press the INFO (
/
) button repeatedly until the
number you want appears, then
press the SEL/RESET button to
enter your selection.
If you sometimes find that the
temperature reading is a few
degrees above or below the actual
temperature, you can adjust it by
following these instructions:
CONTINUED
Adjust Outside Temp. Display
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
97
10/08/04 18:58:33 31SJA660_102
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
To exit ADJUST OUTSIDE TEMP.
DISPLAY without changing the
current setting, select EXIT by
pressing the INFO (
/
) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
If your choice is not set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
adjust outside air temperature
display setup.
Multi-Information Display
98
10/08/04 18:58:40 31SJA660_103
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
▲ ▼
While METER SETUP is shown in
the CUSTOMIZE GROUP of the
multi-information display, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO (
/
) button until
you see the above display.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO (
/
) button, then press the
SEL/RESET button to enter your
selection.
To cause trip A, average fuel
economy A, and average speed to
reset every time you refuel your
vehicle, follow these instructions:
CONTINUED
Multi-Information Display
Trip A Reset with Ref uel
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
99
10/08/04 18:58:48 31SJA660_104
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the trip
A reset with refuel setup.
To exit TRIP A RESET with
REFUEL without changing the
current setting, select EXIT by
pressing the INFO (
/
) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
Multi-Information Display
100
10/08/04 18:58:55 31SJA660_105
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
−
−
−
▲ ▼
While METER SETUP is shown in
the CUSTOMIZE GROUP of the
multi-information display, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO (
/
) button until
you see the above display.
IGN OFF
The elapsed time is
reset when you turn the ignition
switch to the LOCK (0) position.
TRIP A
The elapsed time is reset
when Trip A is reset.
TRIP B
The elapsed time is reset
when Trip B is reset.
Press the SEL/RESET button. The
screen changes as shown above.
Select the desired setting by
pressing the INFO (
/
) button,
then press the SEL/RESET button
to enter your selection.
There are three elapsed time reset
choices you can make:
CONTINUED
Elapsed Time Reset
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
101
10/08/04 18:59:05 31SJA660_106
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
To exit ELAPSED TIME RESET
without changing the current setting,
select EXIT by pressing the INFO
(
/
) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
If your choice is not set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
elapsed time reset setup.
Multi-Information Display
102
10/08/04 18:59:12 31SJA660_107
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
▲
▼
▲ ▼
▲
▼
There are two position setups you
can make:
MEMORY POSITION LINK
AUTO TILT & TELESCOPIC
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select POSITION SETUP by
pressing the INFO (
/
) button,
and then press the SEL/RESET
button.
Each time you press the INFO (
/
) button, the screen changes as
shown in the illustration. Press the
INFO (
/
) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
CONTINUED
Position Setup
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
103
see page 104
see page 106
Press the
or
button.
Press the SEL/RESET button.
10/08/04 18:59:24 31SJA660_108
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
When Memory Position Link is set
to ON, the driver’s seat, the steering
wheel, and the outside mirror
positions move to the positions
stored in memory. To cause the
memory to activate, open the driver’s
door with the remote, or grab the
door handle while carrying the
remote.
To set the seat memory position, see
page
. For information on using
the remote, see page
.
While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to the above display.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO (
/
) button, then press the
SEL/RESET button to enter your
selection.
164
174
Memory Position Link
Multi-Information Display
104
10/08/04 18:59:32 31SJA660_109
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
To exit MEMORY POSITION LINK
without changing the current setting,
select EXIT by pressing the INFO
(
/
) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
memory position link setup.
CONTINUED
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
105
10/08/04 18:59:40 31SJA660_110
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
▲ ▼
When AUTO TILT & TELESCOPIC
is set to ON, the steering wheel
automatically moves fully in and up
when you turn the ignition switch to
the LOCK (0) position and release it,
or when you remove the built-in key
from the ignition switch.
While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO (
/
) button until
you see the above display.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO (
/
) button, then press the
SEL/RESET button to enter your
selection.
Auto Tilt & Telescopic
Multi-Information Display
106
10/08/04 18:59:47 31SJA660_111
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
To exit AUTO TILT &
TELESCOPIC without changing the
current setting, select EXIT by
pressing the INFO (
/
) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the auto
tilt and telescopic setup.
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
107
10/08/04 18:59:54 31SJA660_112
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲
▼
▲ ▼
▲
▼
▲
▼
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO (
/
) button, the screen changes as
shown in the illustration. Press the
INFO (
/
) button until you see
the custom setting then press the
SEL/RESET button to enter your
selection.
There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO (
/
) button, then press the SEL/
RESET button.
Keyless Access Setup
Multi-Information Display
108
see page 109
see page 111
see page 113
Press the
or
button.
Press the SEL/RESET button.
10/08/04 19:00:05 31SJA660_113
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), follow these
instructions:
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to the above display.
Press the SEL/RESET button. The
screen changes as shown above.
Select DRIVER DOOR ONLY or
ALL DOORS by pressing the INFO
(
/
) button, then press the SEL/
RESET button to enter your
selection.
CONTINUED
Door Unlock Mode
Multi-Information Display
Inst
ru
m
e
nt
s
a
nd
Cont
ro
ls
109
10/08/04 19:00:12 31SJA660_114
-------------------------------------------------------------------------------------------------------------------------------------------------------------
▲ ▼
To exit DOOR UNLOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
(
/
) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display for several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the door
unlock mode setup.
Multi-Information Display
110
10/08/04 19:00:20 31SJA660_115
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст