Acura TSX / Honda Accord CL. Manual — part 473
Fig. 268: Removing The Exhaust Manifold
3. Install the exhaust manifold and tighten the bolts/nuts in a crisscross pattern in two or three steps,
beginning with the inner nut.
4. Install the other parts in the reverse order of removal.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
Application
Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt
32 (44)
2004 Acura TSX
2004 ENGINES 2.4L DOHC VTEC - TSX
A/C Compressor Bolt
16 (22)
Battery Base Bolt
16 (22)
Cam Chain Tensioner Arm Bolt
16 (22)
Camshaft Holder Mounting Bolt
16 (22)
Camshaft Position Pulse Plate Bolt
29 (39)
Clutch Line Clamp Bracket Bolt
40 (54)
Connecting Rod Bearing Cap Bolt
(5)
27 (36)
Cylinder Head Bolt
Step 1
(1)
29 (39)
Step 2
(2)
Step 3
(3)
Engine Oil Pan Drain Bolt
32 (44)
Engine Upper Bracket Bolt
47 (64)
Exhaust Camshaft Sprocket Mounting Bolt
53 (72)
Exhaust Manifold
(9)(4)
Bracket Nut
32 (44)
Cover Bolt
16 (22)
Gasket Bolt
32 (44)
Heat Shield Bolt
16 (22)
Mounting Bolt
32 (44)
Self Locking Nut
32 (44)
Exhaust Pipe And Muffler
Air Fuel Ratio (A/F) Sensor
32 (44)
Exhaust Pipe Bolt
16 (22)
Mounting Bolt
16 (22)
Secondary Heated Oxygen Sensor
32 (44)
Self Locking Nut
24 (33)
Evaporative Emission Canister Purge Valve Bracket Bolt
16 (22)
Front Mount
Bracket Bolt
47 (64)
Mounting Bolt
40 (54)
Stop Nut
58 (78)
Intake Manifold
Bracket Bolt
16 (22)
Bracket Nut
16 (22)
Injector Base Nut
16 (22)
Injector Base Bolt
16 (22)
Throttle Body Bolt
16 (22)
Throttle Body Nut
16 (22)
Lower Block Bolt
(8)
16 (22)
2004 Acura TSX
2004 ENGINES 2.4L DOHC VTEC - TSX
Main Bearing Cap Bolt
(6)
21 (29)
Oil Jet Mounting
12 (16)
Oil Pump
Mounting Bolt (10 x 1.25 mm)
32 (44)
Mounting Bolt (8 x 1.25 mm)
16 (22)
Lower Balancer Shaft Holder Bolt (10 x 1.25 mm)
32 (44)
Oil Pump Bolt (8 mm)
20 (27)
Sealing Bolt
29 (39)
Sprocket Mounting Bolt
32 (44)
Upper Balancer Shaft Holder Bolt (8 x 1.25 mm)
20 (27)
Oil Pressure Switch Bolt
13 (18)
Power Steering Pump Bolt
16 (22)
Rear Mount
Bracket Bolt
65 (88)
Mounting Bolt
40 (54)
Stop Nut
51 (69)
Side Engine Mount Bolt
47 (64)
Side Engine Mount Bracket Bolt
32 (44)
Stiffener Bolt
32 (44)
Strut Brace Nut
16 (22)
Transaxle
Lower Front/Rear Mount Nut
32 (44)
Lower Mount Bolt (A/T)
32 (44)
Lower Mount Bolt (M/T) ( 10 x 1.25 mm)
32 (44)
Lower Mount Bolt (M/T) ( 12 x 1.25 mm)
44 (59)
Upper Bracket Bolt
40 (54)
Upper Mount Bracket Bolt
32 (44)
Upper Mount Bolt
40 (54)
Valve Clearance Adjustment Lock Nut
15 (20)
VTC Actuator Mounting Bolt
83 (113)
VTEC Rocker Arm Sealing Bolt
15 (20)
Water Outlet Bolt
16 (22)
Water Outlet Connecting Pipe Mounting Bolt
16 (22)
Water By-Pass Connecting Pipe Bolt
16 (22)
Water Passage Bolt
32 (44)
INCH. Lbs (N.m)
Auto-Tensioner Bolt
106 (12)
Baffle Plate Bolt
106 (12)
Cam Chain Guide Bolt
106 (12)
Camshaft Holder Mounting Bolt
(8)
106 (12)
2004 Acura TSX
2004 ENGINES 2.4L DOHC VTEC - TSX
Chain Case Bolt
106 (12)
Chain Case Cover Bolt
106 (12)
Cylinder Head Cover Bolt
(4)(11)
106 (12)
Engine Oil Pan Maintenance Lid Bolt
88 (10)
Ground Cable Bolt
106 (12)
Harness Bracket Bolt
106 (12)
Harness Clamp Bolt
106 (12)
Harness Connector Bolt
106 (12)
Intake Manifold
106 (12)
Absolute Pressure Sensor Bolt
88 (10)
Cover Nut
106 (12)
Exhaust Gas Recirculation Plate Bolt
106 (12)
Harness Holder Bolt
106 (12)
Intake Air Bypass Thermal Valve
106 (15)
Oil Pan Bolt
(12)
106 (12)
Oil Pump
Chain Tensioner Bolt
106 (12)
Housing Bolt
106 (12)
Lower Balancer Shaft Holder Bolt (6 x 1.0 mm)
106 (12)
Upper Balancer Shaft Holder Bolt (6 x 1.0 mm)
106 (12)
Power Steering (P/S) Hose Bracket Bolt
106 (12)
Power Steering (P/S) Hose Clamp Bolt
106 (12)
Thermostat Housing
106 (12)
Vacuum Line Bolt
106 (12)
Water Pump Bolt
106 (12)
(1)
Tighten in sequence shown in illustration. See Fig. 271 .
(2)
After tightening, tighten all cylinder head bolts in two steps (90° per step).
(3)
If you are using a new cylinder head bolt, tighten the bolt an additional 90°.
(4)
Tighten in 2-3 steps.
(5)
Tightening additional 120°.
(6)
Tightening additional 56°. See Fig. 270 .
(7)
Tighten the bolts/nuts in a crisscross pattern.
(8)
For camshaft holder bolt tightening sequence, see Fig. 269 .
(9)
Tighten all cylinder head bolts in two steps (90° per step). If you are using a new cylinder head bolt,
tighten the bolt an additional 90°.
(10)
Tighten the 8 mm bolts in sequence, see Fig. 274 .
(11)
For cylinder head cover tightening sequence, see Fig. 273 .
2004 Acura TSX
2004 ENGINES 2.4L DOHC VTEC - TSX
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст