Acura TSX / Honda Accord CL. Manual — part 701

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect driver-side air bag connector from
upper cable reel connector. See Fig. 4 . Connect SRS Simulator Lead (07XAZ-SZ30100) and SRS
Inflator Simulator (07SAZ-TB4011A) to upper cable reel connector. Reconnect negative battery cable.
Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE CODE (DTC)
under DIAGNOSTICS. If DTC 11-8 or 11-A is indicated, go to next step. If DTC 11-8 or 11-A is not
indicated, replace driver-side air bag module. See DRIVER-SIDE AIR BAG MODULE under
REMOVAL & INSTALLATION.

3. Turn ignition switch to OFF position. Disable air bag system. Disconnect dashboard wire harness

connector from lower cable reel connector. Connect SRS simulator lead and SRS inflator simulator to
dashboard wire harness connector. Reconnect negative battery cable. Erase DTC memory. Retrieve DTC.
If DTC 11-8 or 11-A is indicated, go to next step. If DTC 11-8 or 11-A is not indicated, replace cable
reel. See CABLE REEL under REMOVAL & INSTALLATION.

4. Turn ignition switch to OFF position. Disable air bag system. Access and disconnect SRS unit connector

"A". See SRS UNIT under REMOVAL & INSTALLATION. See Fig. 33 . Reconnect negative battery
cable. Turn ignition switch to ON position. Disconnect SRS inflator simulator from SRS simulator lead.
DO NOT disconnect simulator lead from dashboard wire harness connector. Measure voltage between
ground and each SRS inflator simulator connector terminal. If voltage is less than 0.5 volt at all terminals,
replace SRS unit. If voltage is more than 0.5 volt at any terminal, replace dashboard wire harness.

DTC 11-9, 11-B

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect driver-side air bag connector from
upper cable reel connector. See Fig. 4 . Connect SRS Simulator Lead (07XAZ-SZ30100) and SRS
Inflator Simulator (07SAZ-TB4011A) to upper cable reel connector. Reconnect negative battery cable.
Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE CODE (DTC)
under DIAGNOSTICS. If DTC 11-9 or 11-B is indicated, go to next step. If DTC 11-9 or 11-B is not
indicated, replace driver-side air bag module. See DRIVER-SIDE AIR BAG MODULE under
REMOVAL & INSTALLATION.

3. Turn ignition switch to OFF position. Disable air bag system. Disconnect dashboard wire harness

connector from lower cable reel connector. Connect SRS simulator lead and SRS inflator simulator to
dashboard wire harness connector. Reconnect negative battery cable. Erase DTC memory. Retrieve DTC.
If DTC 11-9 or 11-B is indicated, go to next step. If DTC 11-9 or 11-B is not indicated, replace cable reel.
See CABLE REEL under REMOVAL & INSTALLATION.

4. Disable air bag system. Access and disconnect SRS unit connector "A". See SRS UNIT under

REMOVAL & INSTALLATION. See Fig. 33 . Disconnect SRS inflator simulator from SRS inflator
simulator lead. DO NOT disconnect simulator lead from dashboard wire harness connector. Measure
resistance between ground and each SRS inflator simulator connector terminal. If resistance is more than
one megohm at all terminals, replace SRS unit. If resistance is less than one megohm at any terminal,
replace dashboard wire harness.

2004 Acura TSX

2004 ACCESSORIES/SAFETY EQUIPMENT Acura - Air Bag Restraint Systems

DTC 12-1, 12-4

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect passenger-side air bag module
connector from dashboard wire harness. See Fig. 5 . Connect SRS Simulator Lead (07XAZ-SZ30100)
and SRS Inflator Simulator (07SAZ-TB4011A) to dashboard wire harness connector. Reconnect negative
battery cable. Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE
CODE (DTC) under DIAGNOSTICS. If DTC 12-1 or 12-4 is indicated, go to next step. If DTC 12-1 or
12-4 is not indicated, replace passenger-side air bag module. See PASSENGER-SIDE AIR BAG
MODULE under REMOVAL & INSTALLATION.

3. Turn ignition switch to OFF position. Disable air bag system. Access and disconnect SRS unit connector

"A". See SRS UNIT under REMOVAL & INSTALLATION. See Fig. 33 . Disconnect SRS inflator
simulator from SRS simulator lead. DO NOT disconnect simulator lead from dashboard wire harness
connector. Measure resistance between each pair of SRS inflator simulator connector terminals. If
resistance is less than one ohm, check connection between SRS unit connector "A" and SRS unit. If
connection is okay, replace SRS unit. If resistance is more than one ohm, replace dashboard wire harness.

DTC 12-3, 12-6

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect passenger-side air bag module
connector from dashboard wire harness. See Fig. 5 . Connect SRS Simulator Lead (07XAZ-SZ30100)
and SRS Inflator Simulator (07SAZ-TB4011A) to dashboard wire harness connector. Reconnect negative
battery cable. Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE
CODE (DTC) under DIAGNOSTICS. If DTC 12-3 or 12-6 is indicated, go to next step. If DTC 12-3 or
12-6 is not indicated, replace passenger-side air bag module. See PASSENGER-SIDE AIR BAG
MODULE under REMOVAL & INSTALLATION.

3. Disable air bag system. Access and disconnect SRS unit connector "A". See SRS UNIT under

REMOVAL & INSTALLATION. See Fig. 33 . Disconnect SRS inflator simulator from SRS simulator
lead. DO NOT disconnect simulator lead from dashboard wire harness connector. Defeat short connector
between SRS unit connector "A" terminals No. 3 and 4, or terminals No. 9 and 10. See DEFEATING
SHORT CONNECTOR under DIAGNOSTICS. Measure resistance between each pair of SRS inflator
simulator connector terminals. If resistance is more than one megohm, replace SRS unit. If resistance is
less than one megohm, replace dashboard wire harness.

DTC 12-8, 12-A

2004 Acura TSX

2004 ACCESSORIES/SAFETY EQUIPMENT Acura - Air Bag Restraint Systems

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect passenger-side air bag module
connector from dashboard wire harness. See Fig. 5 . Connect SRS Simulator Lead (07XAZ-SZ30100)
and SRS Inflator Simulator (07SAZ-TB4011A) to dashboard wire harness connector. Reconnect negative
battery cable. Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE
CODE (DTC) under DIAGNOSTICS. If DTC 12-4 or 12-A is indicated, go to next step. If DTC 12-4 or
12-A is not indicated, replace passenger-side air bag module. See PASSENGER-SIDE AIR BAG
MODULE under REMOVAL & INSTALLATION.

3. Disable air bag system. Access and disconnect SRS unit connector "A". See SRS UNIT under

REMOVAL & INSTALLATION. See Fig. 33 . Reconnect negative battery cable. Turn ignition switch to
ON position. Disconnect SRS inflator simulator from SRS simulator lead. DO NOT disconnect simulator
lead from dashboard wire harness connector. Measure voltage between ground and each SRS inflator
simulator connector terminal. If voltage is less than 0.5 volt at all terminals, replace SRS unit. If voltage
is more than 0.5 volt at any terminal, replace dashboard wire harness.

DTC 12-9, 12-B

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect passenger-side air bag module
connector from dashboard wire harness. See Fig. 5 . Connect SRS Simulator Lead (07XAZ-SZ30100)
and SRS Inflator Simulator (07SAZ-TB4011A) to dashboard wire harness connector. Reconnect negative
battery cable. Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE
CODE (DTC) under DIAGNOSTICS. If DTC 12-9 or 12-B is indicated, go to next step. If DTC 12-9 or
12-B is not indicated, replace passenger-side air bag module. See PASSENGER-SIDE AIR BAG
MODULE under REMOVAL & INSTALLATION.

3. Turn ignition switch to OFF position. Disable air bag system. Access and disconnect SRS unit connector

"A". See SRS UNIT under REMOVAL & INSTALLATION. See Fig. 33 . Disconnect SRS inflator
simulator from SRS simulator lead. DO NOT disconnect simulator lead from dashboard wire harness
connector. Measure resistance between ground and each SRS inflator simulator connector terminal. If
resistance is more than one megohm at all terminals, replace SRS unit. If resistance is less than one
megohm at any terminal, replace dashboard wire harness.

DTC 21-1

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning

2004 Acura TSX

2004 ACCESSORIES/SAFETY EQUIPMENT Acura - Air Bag Restraint Systems

light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Access and disconnect left seat belt pretensioner
connector from SRS left floor harness. See SEAT BELT PRETENSIONERS under REMOVAL &
INSTALLATION. See Fig. 8 . Connect SRS Simulator Lead (07TAZ-SZ5011A) and SRS Inflator
Simulator (07SAZ-TB4011A) to floor harness connector. Reconnect negative battery cable. Erase DTC
memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE CODE (DTC) under
DIAGNOSTICS. If DTC 21-1 is indicated, go to next step. If DTC 21-1 is not indicated, replace left seat
belt pretensioner.

3. Turn ignition switch to OFF position. Disable air bag system. Disconnect right seat belt pretensioner

connector from SRS right floor harness. Access and disconnect SRS unit connector "B". See SRS UNIT
under REMOVAL & INSTALLATION. See Fig. 33 . Measure resistance between SRS unit connector
"B", terminals No. 1 and 2. If resistance is 2-3 ohms, check connection between SRS unit connector "B"
and SRS unit. If connection is okay, replace SRS unit. If resistance is not 2-3 ohms, replace floor harness.

DTC 21-3

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Access and disconnect left seat belt pretensioner
connector from SRS left floor harness. See SEAT BELT PRETENSIONERS under REMOVAL &
INSTALLATION. See Fig. 8 . Connect SRS Simulator Lead (07TAZ-SZ5011A) and SRS Inflator
Simulator (07SAZ-TB4011A) to side harness connector. Reconnect negative battery cable. Erase DTC
memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE CODE (DTC) under
DIAGNOSTICS. If DTC 21-3 is indicated, go to next step. If DTC 21-3 is not indicated, replace left seat
belt pretensioner.

3. Turn ignition switch to OFF position. Disable air bag system. Disconnect right seat belt pretensioner

connector from SRS right floor harness. Access and disconnect SRS unit connector "B". See SRS UNIT
under REMOVAL & INSTALLATION. See Fig. 33 . Disconnect inflator simulator from left seat belt
pretensioner connector. Measure resistance between SRS unit connector "B", terminals No. 1 and 2. If
resistance is more than one megohm, replace SRS unit. If resistance is less than one megohm, replace
floor harness.

DTC 21-8

1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)

memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.

2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under

DISABLING & ACTIVATING AIR BAG SYSTEM. Access and disconnect left seat belt pretensioner

2004 Acura TSX

2004 ACCESSORIES/SAFETY EQUIPMENT Acura - Air Bag Restraint Systems