Acura CSX. Manual — part 303
01
SNR9AA1E10410424251KAAT00
Special Tools Required
14-290
Transmission End Cover
End Cover Removal
A
D
E
I
J
K
L
M
N
O
P
Q
R
S
T
F
G
H
F
R
S
J
F
E
D
F
B, C
Mainshaft holder 07GAB-PF50101
1. Remove the banjo bolts (D), the ATF cooler lines (E), and the sealing washers (F).
2. Remove A/T clutch pressure control solenoid valve A, the ATF joint pipes (G), the ATF pipe (H), and the gasket (I).
3. Remove A/T clutch pressure control solenoid valves B and C, the harness clamp brackets (J), the ATF joint pipes
(K), and the gasket (L).
4. Remove the transmission range switch cover (M).
5. Remove the transmission range switch harness clamps (N) from the clamp bracket (O), then remove the
transmission range switch (P).
6. Remove the end cover (Q), the dowel pins (R), the O-rings (S), and the end cover gasket (T).
08/08/21 14:50:11 61SNR030_140_0292
*01
03
04
*02
14-291
07GAB-PF50101
C
A
B
A
C
B
D
D
E
B
A
C
7. Install the mainshaft holder onto the mainshaft.
8. Engage the park pawl with the park gear.
9. Cut the lock tab (A) of the each shaft locknut (B)
using a chisel (C). Then remove the locknuts and
the conical spring washers from each shaft.
NOTE:
• Countershaft and secondary shaft locknuts have
left-hand threads.
• Keep all of the chiseled particles out of the
transmission.
• Clean the old mainshaft and countershaft
locknuts; they are used to install the press fit idler
gear on the mainshaft, and the park gear on the
countershaft.
10. Remove the mainshaft holder from the mainshaft.
11. Set a two-jaw (or three-jaw) puller (A) on the
countershaft (B) with a spacer (C) between the
puller and the countershaft, then remove the park
gear (D).
12. Install a puller (A) with two 6 x 1.0 mm bolts (B) on
the mainshaft idler gear (C). Set a spacer (D)
between the puller and the mainshaft, then remove
the mainshaft idler gear.
13. Remove the park pawl, the park pawl spring, the
park pawl shaft, and the stop shaft.
14. Remove the park lever from the selector control
shaft.
08/08/21 14:50:12 61SNR030_140_0293
01
02
SNR9AA1E10410445001MCAT00
−
*01
02
SNR9AA1E10410434081KBAT00
−
−
Standard: 57.7
58.7 mm (2.27
2.31 in.)
PARK LEVER STOP
Mark
Part Number
B
C
Special Tools Required
14-292
14-292
Transmission End Cover
Park Lever Stop Inspection and
Adjustment
Idler Gear Shaft Bearing
Replacement
C
A
B
B
C
A
07736-A01000B or
07736-A01000A
B
A
C
07749-0010000
07746-0010400
1. Set the park lever in the P position.
2. Measure the distance (A) between the park pawl
shaft (B) and the park lever roller pin (C).
3. If the distance is out of standard, select and install
the appropriate park lever stop (A) from the table.
1
24537-PA9-003
11.00 mm
(0.433 in.)
11.00 mm
(0.433 in.)
2
24538-PA9-003
10.80 mm
(0.425 in.)
10.65 mm
(0.419 in.)
3
24539-PA9-003
10.60 mm
(0.417 in.)
10.30 mm
(0.406 in.)
4. After replacing the park lever stop, make sure the
distance is within tolerance.
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
• Driver 07749-0010000
• Attachment, 52 x 55 mm 07746-0010400
1. Remove the idler gear shaft bearing (A) from the
end cover (B) using the adjustable bearing puller
and a commercially available 3/8 ’’-16 slide
hammer (C).
2. Install a new bearing in the end cover using the
driver and the 52 x 55 mm attachment.
08/08/21 14:50:13 61SNR030_140_0294
01
*01
SNR9AA1E10410417256KBAT00
01
*01
SNR9AA1E10410417254KBAT00
Special Tools Required
Special Tools Required
14-293
14-293
Selector Control Shaft Oil Seal
Replacement
Selector Control Shaft Bearing
Replacement
A
B
07749-0010000
07746-001A800
07746-001A800
07749-0010000
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-001A800
1. Remove the oil seal (A) from the end cover (B).
2. Install a new oil seal flush to the end cover using
the driver and the 22 x 24 mm attachment.
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-001A800
1. Remove the oil seal from the end cover, then
remove the bearing.
2. Install a new bearing flush to the end cover using
the driver and the 22 x 24 mm attachment.
3. Install a new oil seal.
08/08/21 14:50:14 61SNR030_140_0295
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст