Acura CSX. Manual — part 304
01
SNR9AA1E10410413013KBAT00
14-294
Transmission End Cover
ATF Feed Pipe Replacement
A
C
G
F
E
D
A
C
F
G
B
B
1. Remove the snap rings (A), the ATF feed pipes (B),
and the feed pipe flanges (C) from the end cover (D).
NOTE: Replace the end cover, if the 1st clutch ATF
feed pipe (E) replacement is required.
2. Install new O-rings (F) over the ATF feed pipes.
3. Install the ATF feed pipes in the end cover by
aligning the feed pipe tabs with the indentations in
the end cover.
4. Install new O-rings (G) in the end cover, then install
the feed pipe flanges over the ATF feed pipes.
5. Secure the ATF feed pipes and the feed pipe
flanges with the snap rings.
08/08/21 14:50:14 61SNR030_140_0296
01
SNR9AA1E10410459801KAAT00
14-295
Transmission Housing
Housing and Shaft Assembly Removal
A
B
C
D
E
F
G
H
I
J
K
1. Remove the ATF feed pipe (A) from the idler gear shaft, and remove the ATF lubrication pipe (B) from the
transmission housing.
2. Remove the shift solenoid valve cover (C), the dowel pins (D), and the gasket (E).
3. Disconnect the connectors from the shift solenoid valves, and remove the shift solenoid wire harness (F).
4. Remove the input shaft (mainshaft) speed sensor (G) and the output shaft (countershaft) speed sensor (H).
5. Remove the transmission housing mounting bolts (19 bolts) (I), the transmission hanger (J) and the harness
clamp brackets (K).
08/08/21 14:50:15 61SNR030_140_0297
02
03
04
05
14-296
Transmission Housing
C
A
B
A
B
A
B
C
A
B
C
D
6. Align the spring pin (A) on the selector control shaft
(B) with the transmission housing groove (C) by
turning the selector control shaft with the control
lever.
NOTE: Do not squeeze the end of the selector
control shaft tips together when turning the shaft.
7. Use snap ring pliers to expand the snap ring of the
secondary shaft bearing. Then lift the transmission
housing. Release the snap ring pliers and remove
the transmission housing.
8. Remove the countershaft reverse gear and the
needle bearing.
9. Remove the lock bolt securing the shift fork, then
remove the shift fork with the reverse selector
together.
10. Remove the control lever from the selector control
shaft.
11. Unlock the detent spring (A) from the detent arm
(B).
12. Remove the selector control shaft (A) from the
torque converter housing.
13. Turn the detent arm (B) away from the
countershaft (C).
14. Remove the mainshaft subassembly (A), the
countershaft subassembly (B) and the secondary
shaft subassembly (C) together. Do not bump the
countershaft on the baffle plate (D).
15. Remove the baffle plate.
16. Remove the differential assembly.
08/08/21 14:50:16 61SNR030_140_0298
01
02
SNR9AA1E10411239511KAAT00
Special Tools Required
14-297
Bearing Removal
A
B
• Attachment, 78 x 80 mm 07NAD-PX40100
• Driver 07749-0010000
• Attachment, 42 x 47 mm 07746-0010300
1. Remove the idler gear shaft when removing the
mainshaft bearing and the idler gear shaft bearing.
NOTE: If you are only removing the countershaft
bearing, the idler gear shaft removal is not needed.
2. To remove the mainshaft bearing (A) and the
countershaft bearing (B) from the transmission
housing, expand each snap ring using snap ring
pliers, then push the bearing out using the driver
and the 78 x 80 mm attachment.
NOTE: Do not remove the snap ring unless it’s
necessary to clean the grooves in the housing.
3. Expand the snap ring of the idler gear shaft bearing
using the snap ring pliers, then push the bearing
out using the driver and the 42 x 47 mm attachment.
08/08/21 14:50:17 61SNR030_140_0299
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст