Acura CSX. Manual — part 522
01
02
*01
04
SNR9A00J46643420901FEAT30
Driver’s Door and Left Rear Door
Front Passenger’s Door and Right Rear Door
22-137
Door Lock Actuator Test
A
B
Terminal
Position
1
2
LOCK
UNLOCK
A
B
Terminal
Position
3
4
LOCK
UNLOCK
1. Remove the door panel (see page 20-7).
2. Disconnect the 10P connector (A) from the actuator
(B).
NOTE: The illustration shows the driver’s door.
3. Check actuator operation by connecting power and
ground according to the table. To prevent damage
to the actuator, apply battery voltage only
momentarily.
4. If the actuator does not operate as specified,
replace it.
1. Remove the door panel.
• Front door panel (see page 20-7)
• Rear door panel (see page 20-17)
2. Disconnect the 10P connector (A) from the actuator
(B).
NOTE: The illustration shows the front passenger’s
door.
3. Check actuator operation by connecting power and
ground according to the table. To prevent damage
to the actuator, apply battery voltage only
momentarily.
4. If the actuator does not operate as specified,
replace it.
08/08/21 14:26:05 61SNR030_220_0139
[
]
[
]
[ ]
01
*01
SNR9A00J46643421011FEAT00
Driver’s Door
Passenger’s Door
22-138
Keyless/Power Door Locks/Security System
Door Lock Knob Switch Test
A
B
Left rear door
A
B
Front passenger’s door,
Right rear door
1. Remove the driver’s door panel (see page 20-7).
2. Disconnect the 10P connector (A) from the actuator
(B).
3. Check for continuity between the terminals.
• There should be continuity between terminals
No. 6 and No. 5 when the door lock knob switch
is in the LOCK position and no continuity when
the switch is in the UNLOCK position.
• There should be continuity between terminals
No. 7 and No. 5 when the door lock knob switch
is in the UNLOCK position and no continuity
when the switch is in the LOCK position.
4. If the continuity is not as specified, replace the door
lock actuator.
1. Remove the passenger’s door panel (see page
20-7).
2. Disconnect the 10P connector (A) from the actuator
(B).
3. Check for continuity between the terminals.
There should be continuity between terminals
No. 8
No. 7
and No. 10
No. 5
when the
door lock knob switch in the UNLOCK position and
no continuity when the switch is in the LOCK
position.
: Left rear door
4. If the continuity is not specified, replace the door
lock actuator.
08/08/21 14:26:06 61SNR030_220_0140
01
02
SNR9A00J46643421021FEAT00
Driver’s door
Front passenger’s door
22-139
Door Lock Switch Test
1. Remove the power window master switch and
disconnect its connector (see page 22-219).
2. Check for continuity between the power window
master switch 22P connector terminals.
• There should be continuity between terminals
No. 11 and No. 17 when the door lock switch is in
the LOCK position. (With security)
• There should be no continuity between terminals
No. 11 and No. 17 when the door lock switch is in
the UNLOCK position. (With security)
• There should be continuity between terminals
No. 11 and No. 19 when the door lock switch is in
the UNLOCK position.
• There should be no continuity between terminals
No. 11 and No. 19 when the door lock switch is in
the LOCK position.
3. If the continuity is not as specified, replace the
power window master switch.
1. Remove the front passenger’s power window
switch (see page 22-220).
NOTE: The illustration shows the front passenger’s
door.
2. Check for continuity between the front passenger’s
power window switch 8P connector terminals.
• There should be continuity between terminals
No. 1 and No. 2 when the door lock switch is in
the LOCK position.
• There should be no continuity between terminals
No. 1 and No. 2 when the door lock switch is in
the UNLOCK position.
• There should be continuity between terminals
No. 2 and No. 6 when the door lock switch is in
the UNLOCK position.
• There should be no continuity between terminals
No. 2 and No. 6 when the door lock switch is in
the LOCK position.
3. If the continuity is not as specified, replace the front
passenger’s window switch.
08/08/21 14:26:06 61SNR030_220_0141
01
SNR9A00J46643420703FEAT00
22-140
Keyless/Power Door Locks/Security System
Door Key Cylinder Switch Test
A
B
1. Remove the driver’s door panel (see page 20-7).
2. Disconnect the 10P connector (A) from the key
cylinder switch (B).
3. Check for continuity between the terminals.
• There should be continuity between terminals
No. 9 and No. 5 when the door key cylinder
switch is in LOCK position. (With security)
• There should be no continuity between terminals
No. 9 and No. 5 when the door key cylinder
switch is in the neutral or UNLOCK position.
(With security)
• There should be continuity between terminals
No. 8 and No. 5 when the door key cylinder
switch is in UNLOCK position.
• There should be no continuity between terminals
No. 8 and No. 5 when the door key cylinder
switch is in the neutral or LOCK position.
4. If the continuity is not as specified, replace the door
key cylinder assembly (see page 20-9).
08/08/21 14:26:06 61SNR030_220_0142
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст