Acura CSX. Manual — part 523
01
SNR9A00J46643460333FEAT00
01
SNR9A00J46643432301FEAT00
22-141
22-141
Trunk Lid Release Actuator Test
Hood Switch Test
1. Open the trunk lid.
2. Disconnect the 3P connector from the trunk lid latch
switch/trunk lid release actuator.
3. Check actuator operation by connecting power to
terminal No. 1 and ground to terminal No. 2
momentarily. The actuator should work.
4. If the actuator does not work, replace the trunk lid
latch switch/trunk lid release actuator assembly
(see page 20-185).
1. Open the hood.
2. Disconnect the 2P connector from the hood switch.
3. Check for continuity between the terminals.
• There should be continuity between terminals
No. 1 and No. 2 when the hood is opened (latch
released).
• There should be no continuity between terminals
No. 1 and No. 2 when the hood is closed (latch
pushed down).
4. If the continuity is not as specified, replace the
hood latch assembly (see page 20-181).
Terminal side of
male terminals
08/08/21 14:26:07 61SNR030_220_0143
01
02
SNR9A00J46643436101FHAT00
With HDS
22-142
Keyless/Power Door Locks/Security System
Transmitter Test/Replacement
A
NOTE:
• If the doors unlock or lock with the transmitter, but
the LED on the transmitter does not come on, the LED
is faulty; replace the transmitter.
• If any door is open, you cannot lock the doors with
the transmitter.
• If you unlocked the doors with the transmitter, but do
not open any of the doors within 30 seconds, the
doors relock automatically.
• The doors do not lock or unlock with the transmitter if
the ignition key is inserted in the ignition switch.
1. Press the lock or unlock button five or six times to
reset the transmitter.
• If the locks work, the transmitter is OK.
• If any of the transmitter buttons do not work,
replace the transmitter, then do the transmitter
programming registration (see page 22-329).
• If the locks don’t work, go to step 2.
2. Connect the HDS to the data link connector.
3. Select the KEYLESS from the BODY ELECTRICAL
menu, then enter the KEYLESS CHECK.
4. Press lock, unlock, trunk, or panic button and check
the response on the screen of the HDS.
NOTE: The door lock actuators may or may not
cycle when receiving input from the transmitter.
• If KEYLESS ENTRY TRANSMITTER CODE IS
RECEIVED is indicated, the transmitter is OK. Go
to keyless operation troubleshooting (see page
22-127).
• If DIFFERENT KEYLESS ENTRY TRANSMITTER
CODE IS RECEIVED is indicated, the transmitter is
not registered to the vehicle, if necessary,
reprogram and register the transmitter (see page
22-329).
• If KEYLESS ENTRY TRANSMITTER CODE IS NOT
RECEIVED is indicated, go to step 5.
5. Open the transmitter and check for water damage.
• If you find any water damage, replace the
transmitter, then reprogram and register the
transmitter (see page 22-329).
• If there is no water damage, go to step 6.
6. Replace the transmitter battery (A) with a new one,
and press lock or unlock button and check the
receive condition on the screen of the HDS.
• If KEYLESS ENTRY TRANSMITTER CODE IS
RECEIVED is indicated, the transmitter is OK.
• If KEYLESS ENTRY TRANSMITTER CODE IS NOT
RECEIVED is indicated, go to step 7.
08/08/21 14:26:07 61SNR030_220_0144
03
Without HDS
22-143
7. Use a different known-good keyless transmitter
and repeat steps 3 and 4.
NOTE: The keyless transmitter does not need to be
programmed to the vehicle for this test.
• If (DIFFERENT) KEYLESS ENTRY TRANSMITTER
CODE IS RECEIVED is indicated, replace the
keyless transmitter and do the immobilizer
system registration (see page 22-329).
• If KEYLESS ENTRY TRANSMITTER CODE IS NOT
RECEIVED is indicated, the immobilizer-keyless
control unit is faulty, replace it and do the
immobilizer system registration (see page
22-329).
NOTE: As the keyless transmitter is combined with
the immobilizer transponder, when the
transponder is registered by the HDS, the keyless
transmitter programming is completed
automatically.
1. Start the engine.
• If the engine does not start, go to the immobilizer
symptom troubleshooting (see page 22-323).
• If the engine starts, go to step 2.
2. Press the lock or unlock button five or six times to
reset the transmitter.
• If the locks work, the transmitter is OK.
• If the locks don’t work, go to step 3.
3. Open the transmitter and check for water damage.
• If you find any water damage, replace the
transmitter.
• If there is no water damage, go to step 4.
08/08/21 14:26:07 61SNR030_220_0145
04
22-144
Keyless/Power Door Locks/Security System
A
4. Replace the transmitter battery (A) with a new one,
and try to lock and unlock the doors with the
transmitter by pressing the lock or unlock button
five or six times.
• If the doors lock and unlock, the transmitter is OK.
• If the doors don’t lock and unlock, go to step 5.
5. Reprogram and register the transmitter (see page
22-329), then try to lock and unlock the doors.
• If the doors lock and unlock, the transmitter is OK.
• If the doors don’t lock and unlock, substitute a
known-good transmitter and recheck (see page
22-329). If still not operating, replace the
immobilizer-keyless control unit.
08/08/21 14:26:07 61SNR030_220_0146
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст