Acura CSX. Manual — part 538
01
SNR9A00J32300030111FHAT00
01
SNR9ABDJ32300063101FHAT00
Glove Box Light: 3.4 W
Vanity Mirror Light: 2 W
’08-09 models
22-199
22-199
Glove Box Light Test/Replacement
Vanity Mirror Light Test/
Replacement
B
A
C
A
B
C
1. Open the glove box.
2. Remove the screws, then disconnect the 2P
connector from the glove box light (A).
3. Check for continuity between terminals No. 1 and
No. 2.
• There should be continuity with the switch (B)
released.
• There should be no continuity with the switch (B)
pushed.
4. If the continuity is not as specified, check the bulb
(C). If the bulb is OK, replace the light.
5. Install the glove box light in the reverse order of
removal.
1. Open the sunvisor.
2. Remove the sunvisor (see page 20-84).
3. Disconnect the 2P connector (A) from the vanity
mirror light.
4. Check for continuity between terminals No. 1 and
No. 2.
• With the vanity mirror cover (B) opened, there
should be continuity.
• With the vanity mirror cover closed, there should
be no continuity.
5. If the continuity is not as specified, replace the bulb
(C) or the sunvisor.
6. Install the vanity mirror light in the reverse order of
removal.
08/08/21 14:27:51 61SNR030_220_0201
*01
SNR9AB9J32300035061FHAT00
01
SNR9A00J32373760201FEAT02
With moonroof
22-200
22-200
Interior Lights
Interior Light Switch Test/
Replacement
Trunk Lid Latch Switch Test
B
C
A
’06-07 models
’08-09 models
A
B
NOTE: The interior light switch is built into the
moonroof switch, and it switches the front individual
map light OFF and DOOR positions.
1. Remove the front individual map lights (see page
22-196).
2. Disconnect the moonroof switch 10P
(12P )
connector (A) and map light 3P connector (B).
1: ’06-07 models
2: ’08-09 models
3. Remove the moonroof switch (C).
4. Check for continuity between moonroof switch
10P
(12P ) connector check for continuity
between terminals No. 1
(No. 7 ) and No. 8
(No. 9 ).
1: ’06-07 models
2: ’08-09 models
• There should be continuity when the interior light
switch is in the DOOR position.
• There should be no continuity when the interior
light switch is in the OFF position.
5. If the continuity check is not as specified, replace
the switch.
6. Install the interior light switch in the reverse order
of removal.
1. Open the trunk lid.
2. Disconnect the 3P connector (A) from the trunk lid
latch assembly (B).
3. Check for continuity between terminals No. 2 and
No. 3.
• There should be continuity with the trunk lid
open.
• There should be no continuity with the trunk lid
closed.
4. If the continuity is not as specified, replace the
trunk lid latch assembly.
1
2
1
2
1
2
1
2
08/08/21 14:27:51 61SNR030_220_0202
*01
*02
SNR9AGCJ32300027157FHAT00
+
−
+
−
TYPE S model
Driver’s Footwell Light
Front Passenger’s Footwell Light
22-201
Footwell Light Test/Replacement
(
)
(
)
A
B
(
)
(
)
A
B
1. Remove the dashboard undercover (A).
• Driver’s dashboard undercover (see page 20-103)
• Passenger’s dashboard undercover (see page
20-104)
2. The LED should come on when power is connected
to footwell light illumination 2P connector (B)
terminal No. 1 and ground is connected to terminal
No. 2.
3. If the LED does not come on, replace the footwell
light.
4. Install the footwell light in the reverse order of
removal.
Wire side of
female terminals
Wire side of
female terminals
08/08/21 14:27:52 61SNR030_220_0203
*01
SNR9A00J32323300000DAAT00
22-202
Entry Lights Control System
Component Location Index
CEILING LIGHT
FRONT INDIVIDUAL MAP LIGHTS
MICU
(Built into the under-
dash fuse/relay box)
IGNITION KEY SWITCH
DRIVER’S DOOR SWITCH
LEFT REAR DOOR SWITCH
RIGHT REAR DOOR SWITCH
FRONT PASSENGER’S
DOOR SWITCH
DRIVER’S DOOR LOCK
KNOB SWITCH
IGNITION KEY LIGHT
DRIVER’S DOOR
KEY CYLINDER SWITCH
Test/Replacement,
page 22-197
Test/Replacement (With moonroof),
page 22-196
Input Test, page 22-204
Test, page 22-207
Test, page 22-138
Test, page 22-207
Test, page 22-140
08/08/21 14:27:53 61SNR030_220_0204
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст