Acura CSX. Manual — part 325
02
04
05
06
16-5
A
B
A
B
6. Separate the driveshaft outboard joint from the
front hub using a plastic hammer.
7. Pull the knuckle outward, and separate the
driveshaft outboard joint from the front hub.
8. Left driveshaft: Pry the inboard joint (A) from the
differential using a prybar. Remove the driveshaft
as an assembly.
NOTE:
• Do not pull on the driveshaft (B), or the inboard
joint may come apart. Pull the inboard joint
straight out to avoid damaging the oil seal.
• Be careful not to damage the oil seal using the
prybar.
9. Right driveshaft: Drive the inboard joint (A) off of
the intermediate shaft using a drift and a hammer.
Remove the driveshaft as an assembly.
NOTE: Do not pull on the driveshaft (B), or the
inboard joint may come apart.
08/08/21 14:51:22 61SNR030_160_0005
*01
*02
01
SNR9A00E16226600000LCAT00
Special Tools Required
Welded type
Inboard Joint Side
16-6
16-6
Driveline/Axle
Driveshaft Disassembly
A
A
A
10. Remove the set ring (A) from the left driveshaft
inboard joint.
11. Remove the set ring (A) from the intermediate shaft.
• Threaded adapter, 22 x 1.5 mm 07XAC-001010A
• Threaded adapter, 24 x 1.5 mm 07XAC-001020A
• Slide hammer, 5/8’’-18 UNF, commercially available
• Boot band pliers, commercially available
• Puller, commercially available
1. Remove the boot bands. Be careful not to damage
the boot.
• If the boot band is a welded type (A), cut the boot
band.
• If the boot band is a double loop type (B), lift up
the band end (C), and push it into the clip (D).
• If the boot band is a low profile type (E), pinch the
boot band using commercially available boot
band pliers (F).
08/08/21 14:51:22 61SNR030_160_0006
*01
*02
01
SNR9A00E16226600000LCAT00
Special Tools Required
Welded type
Inboard Joint Side
16-6
16-6
Driveline/Axle
Driveshaft Disassembly
A
A
A
10. Remove the set ring (A) from the left driveshaft
inboard joint.
11. Remove the set ring (A) from the intermediate shaft.
• Threaded adapter, 22 x 1.5 mm 07XAC-001010A
• Threaded adapter, 24 x 1.5 mm 07XAC-001020A
• Slide hammer, 5/8’’-18 UNF, commercially available
• Boot band pliers, commercially available
• Puller, commercially available
1. Remove the boot bands. Be careful not to damage
the boot.
• If the boot band is a welded type (A), cut the boot
band.
• If the boot band is a double loop type (B), lift up
the band end (C), and push it into the clip (D).
• If the boot band is a low profile type (E), pinch the
boot band using commercially available boot
band pliers (F).
08/08/21 14:51:22 61SNR030_160_0006
02
03
04
*01
Double loop type
Low profile type
16-7
C
B
D
F
E
A
D
E
B
C
F
A
A
B
D
C
2. Make marks (A) on each roller (B) and the inboard
joint (C) to identify the locations of the rollers to the
grooves in the inboard joint. Then remove the
inboard joint on a clean shop towel (D). Be careful
not to drop the rollers when separating them from
the inboard joint.
NOTE: Do not engrave or scribe any marks on the
rolling surface.
3. Make marks (A) on the rollers (B) and the spider (C)
to identify the locations of the rollers on the spider,
then remove the rollers.
NOTE: Do not engrave or scribe any marks on the
rolling surfaces.
4. Remove the circlip (D).
5. Make marks (E) on the spider and the driveshaft (F)
to identify the position of the spider on the shaft.
6. Remove the spider.
NOTE: If necessary, use a commercially available
puller.
08/08/21 14:51:23 61SNR030_160_0007
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст