Acura CSX. Manual — part 326
04
02
08
Outboard Joint Side
16-8
Driveline/Axle
A
A
B
A
7. Wrap the splines on the driveshaft with vinyl tape
(A) to prevent damaging the boot.
8. Remove the inboard boot. Be careful not to damage
the boot.
9. Remove the vinyl tape.
1. Remove the boot bands (A). Lift up the three tabs
(B) using a screwdriver, then release the band. Be
careful not to damage the boot.
2. Slide the outboard boot (A) partially to the inboard
joint side. Be careful not to damage the boot.
08/08/21 14:51:24 61SNR030_160_0008
09
*02
11
12
16-9
A
B
C
B
K20Z2 engine model: 22 x 1.5 mm 07XAC-001010A
K20Z3 engine model: 24 x 1.5 mm 07XAC-001020A
A
C
A
3. Wipe off the grease to expose the driveshaft and
the outboard joint inner race.
4. Make a mark (A) on the driveshaft (B) at the same
level as the outboard joint rim (C).
5. Securely clamp the driveshaft in a bench vise with
a shop towel.
6. Remove the outboard joint (A) using the threaded
adapter (B) and a commercially available 5/8’’-18
UNF slide hammer (C).
7. Remove the driveshaft from the bench vise.
8. Remove the stop ring from the driveshaft.
9. Wrap the splines on the driveshaft with vinyl tape
(A) to prevent damaging the boot.
10. Remove the outboard boot. Be careful not to
damage the boot.
11. Remove the vinyl tape.
08/08/21 14:51:24 61SNR030_160_0009
−
−
−
−
*01
*02
*03
*04
SNR9A00E16226622502KBAT00
K20Z2 engine model (left driveshaft only)
K20Z3 engine model
K20Z2 engine model
K20Z3 engine model
Model
Left/Right
Driveshaft
Specified Length (A)
16-10
Driveline/Axle
Dynamic Damper Replacement
A
A
A
A
1. Remove the inboard joint (see page 16-6).
2. Remove the dynamic damper band (see step 1 on
page 16-6).
3. Remove the dynamic damper (A).
4. Install the new dynamic damper and adjust the
position of the new dynamic damper to these
measurements.
NOTE: Be careful not to swap the dynamic dampers.
The right and left dynamic dampers are different
(K20Z3 engine model).
K20Z2
engine
model
Left
293.0
297.0 mm
(11.54
11.69 in.)
K20Z3
engine
model
Left/Right
284.0
288.0 mm
(11.18
11.34 in.)
5. Install the dynamic damper band (see step 10 on
page 16-14).
6. Install the inboard joint (see page 16-12).
08/08/21 14:51:25 61SNR030_160_0010
*01
SNR9A00E16226600000LDAT00
Exploded View
16-11
Driveshaft Reassembly
SET RING
INBOARD JOINT
ROLLERS
SPIDER
DOUBLE LOOP BANDS
(Replacement parts only)
INBOARD BOOT
LOW PROFILE BANDS
DOUBLE LOOP BAND
(Replacement part only)
DRIVESHAFT
STOP RING
LOW PROFILE BAND
DYNAMIC DAMPER
K20Z2 engine model
(left driveshaft)
OUTBOARD BOOT
OUTBOARD JOINT
EAR CLAMP BANDS
CIRCLIP
Right driveshaft
K20Z3 engine model
Replace.
Replace.
Use the grease included
in the inboard boot set.
Replace.
Use the grease included
in the inboard boot set.
Replace.
Replace.
Replace.
Replace.
Use the grease included
in the outboard boot set.
Replace.
08/08/21 14:51:25 61SNR030_160_0011
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст