Acura CSX. Manual — part 31
28
*09
05
30
5-22
Engine Assembly
A
B
B
A
6 x 1.0 mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C
A
51. Connect the evaporative emission (EVAP) canister
hose (A) and the brake booster vacuum hose (B).
52. Install the engine control module (ECM)/powertrain
control module (PCM) bracket (A), then install the
under-hood fuse/relay box (B) to the ECM/PCM
bracket.
53. K20Z3 engine: Install the engine cover.
54. Connect the ECM/PCM connectors (A) and the
engine wire harness connector (B).
55. Install the harness clamps (C).
*10
32
*11
5-23
B
A
6 x 1.0 mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
A
B
C
6 x 1.0 mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
56. Install the ECM/PCM (A), then install the ECM/PCM
cover (B).
57. Connect the battery cables (A) to the under-hood
fuse/relay box.
58. Install the harness clamp (B).
59. Install the pipe (A).
60. Connect the connector (B), and install the harness
clamps (C).
61. Install the under cowl-panel (see step 4 on page
20-164).
62. Install the air cleaner assembly (see page 11-345).
63. Install the front wheels.
64. Do the battery installation procedure (see page
22-69).
65. Inspect for fuel leaks. Turn the ignition switch to
ON (II) (do not operate the starter) so the fuel pump
runs for about 2 seconds and pressurizes the fuel
line. Repeat this operation three times, then check
for fuel leakage at any point in the fuel line.
66. Refill the engine with engine oil (see step 4 on page
8-10).
01
02
SNR9A00A18224000000KBAT10
M/T model
A/T model
5-24
5-24
Engine Assembly
Side Engine Mount Replacement
67. Refill the transmission with fluid:
• Manual transmission (see step 3 on page 13-5)
• Automatic transmission (see step 3 on page
14-232)
68. A/T model: Move the shift lever to each gear, and
verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into
gear smoothly.
70. Refill the radiator with engine coolant, and bleed
the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP
pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
01
02
SNR9A00A18224000000KBAT10
M/T model
A/T model
5-24
5-24
Engine Assembly
Side Engine Mount Replacement
67. Refill the transmission with fluid:
• Manual transmission (see step 3 on page 13-5)
• Automatic transmission (see step 3 on page
14-232)
68. A/T model: Move the shift lever to each gear, and
verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into
gear smoothly.
70. Refill the radiator with engine coolant, and bleed
the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP
pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст