Acura CSX. Manual — part 29
02
K20Z3 engine
5-14
Engine Assembly
SIDE ENGINE MOUNT BRACKET
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
10 x 1.25 mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
A/C COMPRESSOR BRACKET
LOWER TORQUE ROD BRACKET
Replace.
*01
35
02
12
5-15
A/T model
M/T model
07AAK-SNAA120
VSB02C000015
AAR-T1256
B
C
A
D
VSB02C000025
A
2. Raise the vehicle on the lift, and position the
engine/transmission under the vehicle. Lower the
vehicle, and install the universal lifting eyelet
(07AAK-SNAA120). Attach a chain hoist to the
universal eyelet and the transmission hook, then lift
the engine into position in the vehicle.
NOTE: Reinstall the mounting bolts/support nuts in
the sequence given in the following steps. Failure
to follow this sequence may cause excessive noise
and vibration, and reduce engine mount life.
3. Attach the engine hanger adapter (VSB02C000015)
to the threaded hole in the cylinder head.
4. Install the front leg assembly (A), the hook (B), and
the wing nut (C) to an A and Reds engine support
hanger (AAR-T1256) onto the 2006 civic engine
hanger (VSB02C000025). Carefully position the
engine hanger on the vehicle, and attach the hook
to the forward hole in the engine hanger adapter
(D). Tighten the wing nut by hand to lift and support
the engine/transmission.
NOTE: Be careful when working around the
windshield.
5. Loosen the upper torque rod mounting bolt (A).
13
14
*02
09
5-16
Engine Assembly
14 x 1.5 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
12 x 1.25 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
6. Tighten the new side engine mount bracket
mounting bolt and nut.
7. M/T model: Tighten the new transmission
mounting bolt and nuts.
8. Remove the chain hoist.
9. Remove the universal lifting eyelet.
10. A/T model: Remove the transmission hanger
bracket (P/N 21232-RCT-A00).
Replace.
Replace.
*03
11
*04
*05
5-17
A
B
6 x 1.0 mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
12 x 1.25 mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
B
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
A
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
B
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
C
12 x 1.25 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
VSB02C000016
A
C
D
B
14 x 1.5 mm
103 N·m
(10.5 kgf·m, 75.9 lbf·ft)
14 x 1.5 mm
103 N·m
(10.5 kgf·m, 75.9 lbf·ft)
11. A/T model: Install the transmission mount bracket
(A), then install the ground cable (B).
12. A/T model: Install the transmission mount, then
tighten the transmission mount stiffener mounting
bolt (A) and the new transmission mount mounting
bolts (B).
13. A/T model: Tighten the new transmission mounting
bolt and nuts (C).
14. Raise the vehicle on the lift.
15. Attach the front subframe adapter (VSB02C000016)
to the front subframe, and hang the belt (A) of the
front subframe adapter over the front of the
subframe (B). Secure the belt with its stop (C), then
tighten the wing nut (D).
16. Line up the slots in the front subframe adapter
arms with the bolt holes on the corner of the jack
base, then securely attach them with four bolts. Lift
the subframe up to the body.
17. Loosely install the new front subframe mounting
bolts.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст