Acura CSX. Manual — part 316
07
01
02
14-337
Improperly installed:
Properly installed:
A
B
B
A
A
B
C
D
E
A
B
G
E
D
C
F
10. Make sure the oil seal of the spring retainer (A) is
properly installed on the clutch piston (B). If the oil
seal was damaged or cracked, replace the spring
retainer.
11. Install the waved spring (A) in the 1st clutch drum
(B). Starting with the clutch wave-plate, alternately
install the clutch wave-plates (C) (4), and the discs
(D) (4), and install the clutch end-plate (E) with the
flat side down on the top disc.
12. Install the waved spring (A) in the 2nd clutch drum
(B). Install the clutch flat-plate (C), and the clutch
disc (D). Starting with the clutch wave-plate,
alternately install the clutch wave-plates (E) (3), and
the discs (F) (3), and install the clutch end-plate (G)
with the flat side down on the top disc.
08/08/21 14:52:24 61SNR030_140_0339
01
04
01
SNR9AA1E10411210251LDAT00
Special Tools Required
14-338
14-338
Shafts and Clutches
4th and 5th Clutch Reassembly
A
B
E
D
C
F
G
A
B
13. Install the waved spring (A) in the 3rd clutch drum
(B). Install the clutch flat-plate (C), and the clutch
disc (D). Starting with the clutch wave-plate,
alternately install the clutch wave-plates (E) (3), and
the discs (F) (3), and install the clutch end-plate (G)
with the flat side down on the top disc.
14. Install the snap ring using a screwdriver to secure
the clutch end-plate.
15. Check that the clutch piston moves by applying air
pressure into fluid passage.
Clutch spring compressor set 07LAE-PX40000
1. Soak the clutch discs thoroughly in ATF for at least
30 minutes.
2. Install new O-rings (A) on the clutch piston (B).
08/08/21 14:52:25 61SNR030_140_0340
01
04
01
SNR9AA1E10411210251LDAT00
Special Tools Required
14-338
14-338
Shafts and Clutches
4th and 5th Clutch Reassembly
A
B
E
D
C
F
G
A
B
13. Install the waved spring (A) in the 3rd clutch drum
(B). Install the clutch flat-plate (C), and the clutch
disc (D). Starting with the clutch wave-plate,
alternately install the clutch wave-plates (E) (3), and
the discs (F) (3), and install the clutch end-plate (G)
with the flat side down on the top disc.
14. Install the snap ring using a screwdriver to secure
the clutch end-plate.
15. Check that the clutch piston moves by applying air
pressure into fluid passage.
Clutch spring compressor set 07LAE-PX40000
1. Soak the clutch discs thoroughly in ATF for at least
30 minutes.
2. Install new O-rings (A) on the clutch piston (B).
08/08/21 14:52:25 61SNR030_140_0340
02
03
*01
01
14-339
A
B
C
B
A
07LAE-PX40000
A
B
3. Install the clutch piston (A) in the clutch drum (B)
while applying pressure and rotating to ensure
proper seating. Do not pinch the O-ring.
4. Set the return spring (A) and the spring retainer (B)
on the clutch piston, and position the snap ring (C)
on the spring retainer.
5. Install the clutch spring compressor set.
6. Be sure the clutch spring compressor set (A) is
adjusted to have full contact with the spring
retainer (B).
08/08/21 14:52:26 61SNR030_140_0341
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст