Acura CSX. Manual — part 195
*01
*02
*03
*04
SNR9AA8E34100014001FEAT02
13-6
Manual Transmission
Back-up Light Switch Test
A
BACK-UP LIGHT SWITCH 2P CONNECTOR
A
29 N·m
(3.0 kgf·m,
22 lbf·ft)
B
BACK-UP LIGHT SWITCH 2P CONNECTOR
1. Disconnect the back-up light switch 2P connector
(A).
2. Check for continuity between back-up light switch
2P connector terminals No. 1 and No. 2. There
should be continuity only when the shift lever is in
reverse.
• If the test result is OK, go to step 5.
• If the test result is faulty, go to step 3.
3. Remove the back-up light switch (A). Check for
continuity between back-up light switch 2P
connector terminals No. 1 and No. 2. There should
be continuity when the actuator (B) is pressed, and
no continuity when the actuator is released.
• If the test result is OK, check the reverse shift
mechanism in the transmission.
• If the test result is faulty, replace the back-up light
switch.
4. Apply liquid gasket (08C70-K0230M, 08C70-
K0334M, or 08C70-X0331S) to the threads of the
back-up light switch, and install it on the
transmission housing.
5. Connect the back-up light switch 2P connector.
Terminal side of male terminals
Terminal side of male terminals
08/08/21 14:44:18 61SNR030_130_0008
#
@
01
02
03
SNR9AA8E34150100000KAAT00
Special Tools Required
13-7
Transmission Removal
A
B
C
D
A
A
B
A
B
C
• Engine hanger adapter VSB02C000015
• 2006 Civic engine hanger VSB02C000025
• Engine support hanger, A and Reds AAR-T1256
• Front subframe adapter VSB02C000016
These special tools are available through the Acura
Canada Technical Tools Department; FAX
866-398-8665/e-mail: ch_technicaltools
ch.honda.com
NOTE: Use fender covers to avoid damaging painted
surfaces.
1. Do the battery removal procedure (see page 22-69).
2. Remove the cowl cover and the under-cowl panel
(see page 20-163).
3. Remove the air cleaner assembly (see page 11-345).
4. Remove the harness clips (A) and the intake air
duct (B), then remove the battery base (C) with the
coolant reservoir (D).
5. Remove the clutch line bracket (A), then carefully
move the slave cylinder (B) out of the way to avoid
bending the clutch line.
NOTE: Do not press the clutch pedal after the slave
cylinder has been moved.
6. Disconnect the back-up light switch connector (A),
the output shaft (countershaft) speed sensor
connector (B), and the harness clips (C).
08/08/21 14:44:19 61SNR030_130_0009
*01
*02
05
06
’06 model
’07-09 models
13-8
Manual Transmission
C
A
A
D
D
C
B
D
D
A
B
C
A
A
7. Remove the cotter pins (A) or the lock pins (B) and
the shift cable bracket (C), then disconnect the shift
cables (D) from the change lever assembly.
Carefully remove both cables and the bracket
together to avoid bending the cables.
8. Remove the harness clips (A) from the clutch cable
bracket (B) and the harness bracket (C).
9. Remove the air cleaner housing bracket (A).
08/08/21 14:44:20 61SNR030_130_0010
*03
*04
03
10
13-9
A
B
C
VSB02C000015
VSB02C000025
AAR-T1256
A
D
B
C
10. Remove the engine wire harness cover (A) by
lifting up on the lock tab (B), then slide the harness
cover forward off the bracket (C).
11. Attach the engine hanger adapter (VSB02C000015)
to the threaded holes in the cylinder head.
12. Install the front leg assembly (A), the hook (B), and
the wingnut (C) from an A and Reds engine support
hanger (AAR-T1256) onto the 2006 Civic engine
hanger (VSB02C000025). Carefully position the
engine hanger on the vehicle, and attach the hook
to the forward hole in the engine hanger adapter
(D). Tighten the wingnut by hand to lift and support
the engine/transmission assembly.
NOTE: Use care when working around the
windshield.
13. Remove the two upper transmission mounting
bolts.
08/08/21 14:44:21 61SNR030_130_0011
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст