Acura CSX. Manual — part 531
01
02
03
SNR9A00J32133131131MBAT00
22-173
Headlight Adjustment
A
A
7.5 m (25 ft)
A
A
B
Headlights become very hot during use; do not
touch them or any attaching hardware immediately
after they have been turned off.
Before adjusting the headlights:
• Park the vehicle on a level surface.
• Make sure the tire pressures are correct.
• The driver or someone who weighs the same should
sit in the driver’s seat.
1. Clean the outer lens so that you can see the center
(A) of the headlights.
2. Park the vehicle in front of a wall or a screen (A).
3. Turn the low beams on.
4. Determine if the headlights are aimed properly.
Vertical adjustment:
Measure the height of the headlights (A).
Adjust the cut line (B) to the lights height.
08/08/21 14:27:01 61SNR030_220_0175
04
*01
01
SNR9A00J32133131131KBAT00
22-174
22-174
Exterior Lights
Headlight Replacement
U: UP
D: DOWN
A
A
D
B
C
A
5. If necessary, open the hood and adjust the
headlights to local requirements by turning the
adjusters (A).
A transient high tension (25,000 V) occurs at the
bulb sockets or the high intensity discharge (HID)
lamps when the combination light switch is turned
ON, it may cause serious electrical shock or
electrocution if you do not observe the cautions.
Do not service the headlights assembly in wet
conditions, such as rain or snow, near a sprinkler
system, or when your hands are wet to prevent
electrocution.
1. Remove the front bumper (see page 20-146).
2. Remove the connectors (A) from the headlight
assembly (B).
3. Remove the five bolts, then remove the headlight.
4. Remove the bolt (C) and the corner upper beam (D)
from the headlight.
5. Install the headlight in the reverse order of removal.
6. After replacement, adjust the headlight to local
requirements.
The illustration is shown from
back side of left headlight.
08/08/21 14:27:01 61SNR030_220_0176
04
*01
01
SNR9A00J32133131131KBAT00
22-174
22-174
Exterior Lights
Headlight Replacement
U: UP
D: DOWN
A
A
D
B
C
A
5. If necessary, open the hood and adjust the
headlights to local requirements by turning the
adjusters (A).
A transient high tension (25,000 V) occurs at the
bulb sockets or the high intensity discharge (HID)
lamps when the combination light switch is turned
ON, it may cause serious electrical shock or
electrocution if you do not observe the cautions.
Do not service the headlights assembly in wet
conditions, such as rain or snow, near a sprinkler
system, or when your hands are wet to prevent
electrocution.
1. Remove the front bumper (see page 20-146).
2. Remove the connectors (A) from the headlight
assembly (B).
3. Remove the five bolts, then remove the headlight.
4. Remove the bolt (C) and the corner upper beam (D)
from the headlight.
5. Install the headlight in the reverse order of removal.
6. After replacement, adjust the headlight to local
requirements.
The illustration is shown from
back side of left headlight.
08/08/21 14:27:01 61SNR030_220_0176
01
02
SNR9AGPJ32127127151KBAT00
*01
*02
SNR9A0DJ32127127151KBAT00
’07-08 models
’09 model
FOG LIGHT: 55 W
FOG LIGHT: 55 W
22-175
22-175
Fog Light Replacement
A
B
A
A
B
A
1. Remove the fog light cover.
2. Remove the mounting screw from the fog light.
3. Remove the fog light (A) from the front bumper.
4. Disconnect the 2P connector (B) from the fog light.
5. Turn the bulb socket (A) 60 ° counterclockwise to
remove it from the housing.
6. Install the fog light in the reverse order of removal.
7. After replacement, adjust the fog lights to local
requirements (see page 22-176).
1. Remove the mounting screw from the fog light.
2. Remove the fog light (A) from the front bumper.
3. Disconnect the 2P connector (B) from the fog light.
4. Turn the bulb socket (A) 60 ° counterclockwise to
remove it from the housing.
5. Install the fog light in the reverse order of removal.
6. After replacement, adjust the fog lights to local
requirements (see page 22-176).
08/08/21 14:27:02 61SNR030_220_0177
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст