Acura CSX. Manual — part 197
#
@
01
*01
*02
*03
SNR9AA8E34150100000KCAT00
Special Tools Required
13-14
Manual Transmission
Transmission Installation
A
A
A
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 9 lbf·ft)
• Engine hanger adapter VSB02C000015
• 2006 Civic engine hanger VSB02C000025
• Engine support hanger, A and Reds AAR-T1256
• Front subframe adapter VSB02C000016
These special tools are available through the Acura
Canada Technical Tools Department; FAX
866-398-8665/e-mail: ch_technicaltools
ch.honda.com
NOTE: Use fender covers to avoid damaging painted
surfaces.
1. Loosen the upper torque rod mounting bolt (A).
2. Made sure that the two dowel pins (A) are installed
in the clutch housing.
3. Check the release fork and the release bearing, and
reinstall them with the appropriate grease
(see page 12-24).
4. Place the transmission on the transmission jack,
and raise it to the engine level.
5. Install the transmission mounting bolts.
6. Install the clutch cover.
7. Install the intermediate shaft (see page 16-27).
8. Install the driveshafts inboard joint (see step 6 on
page 16-21).
08/08/21 14:44:25 61SNR030_130_0016
05
06
01
13-15
VSB02C000016
B
14 x 1.5 mm
103 N·m
(10.5 kgf·m, 76 lbf·ft)
B
14 x 1.5 mm
103 N·m
(10.5 kgf·m, 76 lbf·ft)
A
A
B
B
A
9. Support the front subframe with the subframe
adapter (VSB02C000016) and a jack.
10. Install the front subframe (A). Loosely install new
subframe mounting bolts (B).
11. Align the front subframe reference marks (A) to the
body (B), as noted during removal. Tighten the
front subframe mounting bolts to the specified
torque.
Replace.
Replace.
08/08/21 14:44:26 61SNR030_130_0017
02
03
02
05
13-16
Manual Transmission
14 x 1.5 mm
88 N·m
(9.0 kgf·m,
65 lbf·ft)
12 x 1.25 mm
74 N·m
(7.5 kgf·m, 55 lbf·ft)
A
A
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12. Install a new lower torque rod bracket mounting
bolt.
13. Install the front engine mount bracket (A) on the
transmission and the engine with new bolts.
14. Loosely tighten a new front engine mount
mounting bolt (A), then attach the lower radiator
hose to the front engine mount bracket.
15. Install new middle subframe mounting bolts.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:44:26 61SNR030_130_0018
12
13
*09
*04
13-17
A
B
10 x 1.25 mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)
10 x 1.25 mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
A
B
C
10 x 1.25 mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
10 x 1.25 mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)
10 x 1.25 mm
38 N·m
(3.9 kgf·m,
28 lbf·ft)
12 x 1.25 mm
74 N·m
(7.5 kgf·m,
55 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
12 x 1.25 mm
74 N·m
(7.5 kgf·m,
55 lbf·ft)
12 x 1.25 mm
74 N·m
(7.5 kgf·m, 55 lbf·ft)
B
A
A
14 x 1.5 mm
93 N·m
(9.5 kgf·m,
69 lbf·ft)
16. Install the steering gearbox stiffener plate (A) and
the harness clip (B).
17. Install the stiffener plate (A) and the mounting
bracket (B). Connect the exhaust mounting rubber
(C).
18. Connect the lower ball joint and the lower arm (see
step 8 on page 16-21).
19. Lower the vehicle on the lift.
20. Install the transmission mount bracket (A), and
connect the ground cable (B).
21. Raise the vehicle on the lift.
22. Loosen and retighten the lower torque rod
mounting bolt (A).
23. Refill the transmission with the recommended
transmission fluid (see page 13-5).
24. Lower the vehicle on the lift.
Replace.
Replace.
Replace.
08/08/21 14:44:27 61SNR030_130_0019
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст