Acura CSX. Manual — part 292
24
25
26
27
14-249
A
B
A
B
C
C
A
B
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
A
B
C
A
B
C
D
E
D
E
39. Connect the ATF cooler hoses (A) to the ATF cooler
lines (B), and secure the hoses with the clips (C)
(see page 14-253).
40. Secure the harness clamp bracket (A) on the
transmission hanger (B) with the bolt.
41. Install the water hose (A) to its clamp (B) at the
mark (C).
42. Connect the shift solenoid wire harness connector
(A), the A/T clutch pressure control solenoid valve
B connector (B), and the A/T clutch pressure control
solenoid valve C connector (C), and install the
harness clamps (D) on the clamp brackets (E).
08/08/21 14:48:48 61SNR030_140_0251
28
01
30
02
14-250
Automatic Transmission
E
F
A
B
C
D
G
A
B
C
D
D
A
B
43. Connect the 3rd clutch transmission fluid pressure
switch connector.
44. Connect the output shaft (countershaft) speed
sensor connector (A) and the input shaft
(mainshaft) speed sensor connector (B), and install
the harness clamp (C) on its clamp bracket (D).
45. Install the transmission range switch connector (E)
on the connector bracket, and connect the
connector. Install the harness clamp (F) to the
clamp bracket (G).
46. Connect the A/T clutch pressure control solenoid
valve A connector (A) and the 2nd clutch
transmission fluid pressure switch connector (B),
and install the harness clamps (C) on the clamp
brackets (D).
47. Install the harness cover (A) on its bracket (B).
08/08/21 14:48:49 61SNR030_140_0252
03
04
05
14-251
A
12 x 1.25 mm
64 N·m
(6.5 kgf·m,
47 lbf·ft)
A
12 x 1.25 mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
B
12 x 1.25 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
A
14 x 1.5 mm
93 N·m (9.5 kgf·m, 69 lbf·ft)
48. Loosen the upper torque rod mounting bolt (A).
49. Loosen the transmission bolt (A) and the nuts (B).
50. Loosen the lower torque rod mounting bolt (A).
51. Tighten the lower torque rod mounting bolt.
52. Tighten the transmission mounting bolt and the
nuts.
53. Tighten the upper torque rod mounting bolt.
08/08/21 14:48:49 61SNR030_140_0253
14-252
Automatic Transmission
54. Refill the transmission with ATF (see step 5 on page
14-232).
55. Install the battery tray, the battery base, and the
resonator.
56. Install the air cleaner assembly (see page 11-345)
and the intake air duct (see page 11-348).
57. Install the front grille cover (see page 20-163).
58. Install the under-cowl lower panel and the cowl
cover (see page 20-163).
59. Do the battery installation procedure (see page
22-69).
60. Install the front wheels.
61. Set the parking brake. Start the engine, and shift
the transmission through all positions three times.
62. Check the shift lever operation, the A/T gear
position indicator operation, and the shift cable
adjustment.
63. Check and adjust the front wheel alignment
(see page 18-5).
64. Install the splash shield.
65. Start the engine with the shift lever in P or N, and
warm it up to normal operating temperature (the
radiator fan comes on). Turn off the engine, and
check the ATF level (see page 14-231).
66. Road-test the vehicle (see page 14-208).
08/08/21 14:48:50 61SNR030_140_0254
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст