Acura CSX. Manual — part 434
01
02
SNR9AB9J34200041401KBAT00
20-58
Moonroof
Sunshade Replacement
Fastener Locations
: Screw, 4
B
A
Fastener Locations
: Screw, 4
A
B
1. Remove the drain channel (see page 20-57).
2. Slide the sunshade (A) until you can see both
sunshade slider spacers (B).
3. Remove the screws, then remove both spacers.
4. While lifting the front portion of the sunshade (A),
move the sunshade forward until you can see both
sunshade rear hooks (B). Do not damage the
sunshade or the hooks.
5. Remove the screws, then remove both rear hooks.
08/08/21 15:00:21 61SNR030_200_0060
03
04
01
SNR9AB9J34200041001KBAT00
20-59
20-59
Motor Replacement
A
B
A
Fastener Locations
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
: Bolt, 2
6. Remove the sunshade (A).
7. Remove both front sunshade base sliders (A) and
both rear sunshade base sliders (B).
8. Install the sunshade in the reverse order of removal,
and check the glass position adjustment (see page
20-55).
9. Check for water leaks. Let the water run freely from
a hose without a nozzle. Do not use a high-pressure
spray.
1. Remove the headliner (see page 20-84).
2. Put on gloves to protect your hands. Disconnect the
connector (A), and remove the bolts, then remove
the motor (B).
3. Install the motor in the reverse order of removal,
and note these items:
• Make sure the connector is plugged in properly.
• Reset the moonroof control unit (see page
22-287).
• Check the motor operation.
08/08/21 15:01:20 61SNR030_200_0061
03
04
01
SNR9AB9J34200041001KBAT00
20-59
20-59
Motor Replacement
A
B
A
Fastener Locations
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
: Bolt, 2
6. Remove the sunshade (A).
7. Remove both front sunshade base sliders (A) and
both rear sunshade base sliders (B).
8. Install the sunshade in the reverse order of removal,
and check the glass position adjustment (see page
20-55).
9. Check for water leaks. Let the water run freely from
a hose without a nozzle. Do not use a high-pressure
spray.
1. Remove the headliner (see page 20-84).
2. Put on gloves to protect your hands. Disconnect the
connector (A), and remove the bolts, then remove
the motor (B).
3. Install the motor in the reverse order of removal,
and note these items:
• Make sure the connector is plugged in properly.
• Reset the moonroof control unit (see page
22-287).
• Check the motor operation.
08/08/21 15:01:20 61SNR030_200_0061
01
02
03
*01
SNR9AB9J34200040801KBAT00
20-60
Moonroof
Frame and Drain Tube Replacement
A
A
B
C
A
A
C
C
C
A
B
Fastener Locations
: Bolt, 9
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
B
B
B
B
C
A
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
1. Remove these items:
• Headliner (see page 20-84)
• Moonroof glass (see page 20-55)
2. Put on gloves to protect your hands. Disconnect the
motor connector (A).
3. Disconnect the drain tubes (A).
4. Remove the roof wire harness (B) by detaching the
harness clips (C).
5. With an assistant holding the frame (A), remove the
bolts, starting at the rear, and release the rear
hooks (B) by moving the frame forward.
6. With the help of an assistant, carefully remove the
frame through the front door opening. Take care
not to scratch the interior trim or the body, or tear
the seat covers.
7. To remove a front drain tube (A) from the body,
remove the kick panel, left or right (see page 20-66),
and the driver’s dashboard undercover (see page
20-103) or the passenger’s dashboard undercover
(see page 20-104). Detach the clips (B) and remove
the drain valve (C) from the body hole, then remove
the front drain tube.
08/08/21 15:01:21 61SNR030_200_0062
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст