Acura CSX. Manual — part 288
#
@
*01
01
SNR9AA1E10410400000KAAT00
Special Tools Required
14-233
Transmission Removal
A
18 x 1.5 mm
49 N·m
(5.0 kgf·m, 36 lbf·ft)
B
A
B
• Engine hanger plate 07AAK-SNAA120
• Engine support hanger, A and Reds AAR-T1256
• 2006 Civic engine hanger VSB02C000025
• Front subframe adapter VSB02C000016
Available through Acura Canada Technical Tools
Department; Fax
866-398-8665/
e-mail: ch_technicaltools
ch.honda.com
NOTE:
• Use fender covers to avoid damaging painted
surfaces.
• Special tool engine support hanger must be used
with the side engine mount installed.
1. Remove the cowl cover (see page 20-163) and the
under-cowl panel.
2. Remove the front grille cover (see page 20-163).
3. Do the battery removal procedure (see page 22-69).
4. Remove the intake air duct (see page 11-348) and
the air cleaner assembly (see page 11-345).
5. Remove the battery tray, the battery base, and the
resonator.
6. Raise the vehicle on a lift, and make sure it is
securely supported and remove the front wheels.
7. Remove the splash shield.
8. Remove the drain plug (A), and drain the automatic
transmission fluid (ATF).
9. Reinstall the drain plug with a new sealing washer
(B).
10. Secure the hood in the vertical position.
11. Remove the harness cover (A) from its bracket (B).
Replace.
08/08/21 14:46:53 61SNR030_140_0235
03
02
05
06
14-234
Automatic Transmission
A
B
C
D
D
A
B
C
D
E
F
C
G
A
B
C
D
E
D
E
12. Disconnect the A/T clutch pressure control solenoid
valve A connector (A) and the 2nd clutch
transmission fluid pressure switch connector (B),
and remove the harness clamps (C) from the clamp
brackets (D).
13. Remove the harness clamp (A) from the clamp
bracket (B). Disconnect the transmission range
switch connector (C), and remove the connector
from its bracket.
14. Disconnect the output shaft (countershaft) speed
sensor connector (D) and the input shaft
(mainshaft) speed sensor connector (E), and
remove the harness clamp (F) from the clamp
bracket (G).
15. Disconnect the 3rd clutch transmission fluid
pressure switch connector.
16. Disconnect the shift solenoid wire harness
connector (A), the A/T clutch pressure control
solenoid valve B connector (B), and the A/T clutch
pressure control solenoid valve C connector (C),
then remove the harness clamps (D) from the
clamp brackets (E).
08/08/21 14:46:54 61SNR030_140_0236
07
08
09
10
14-235
A
B
A
B
A
B
A
B
C
07AAK-SNAA120
17. Disconnect the ATF cooler hoses (A) from the ATF
lines (B). Turn the end of the ATF cooler hoses up to
prevent ATF from flowing out, then plug the hoses
and lines.
18. Remove the bolt securing the harness clamp
bracket (A) from the transmission hanger (B).
19. Remove the water hose from its clamp.
20. Remove the air cleaner housing mounting bracket
(A).
21. Install the engine hanger plate (07AAK-SNAA120)
on the stud nut (B) with a 8 x 1.25 - 16 mm bolt (C).
Use only the 8 x 1.25 mm and 16 mm in length of
the threaded bolt. If you use other than 16 mm
threaded-length bolt, it may damage the engine
cylinder head.
08/08/21 14:46:55 61SNR030_140_0237
11
12
13
14-236
Automatic Transmission
07AAK-SNAA120
VSB02C000025
A
B
C
22. Install the front leg assembly (A), the hook (B), and
the wing nut (C) from the A and Reds engine
support hanger (AAR-T1256) onto the 2006 civic
engine hanger (VSB02C000025). Carefully position
the engine hanger on the vehicle, and attach the
hook to the slotted hole in the engine hanger plate
(07AAK-SNAA120). Tighten the wing nut by hand to
lift and support the engine. Use care when working
around the windshield.
23. Remove the nuts and the bolt securing the lower
arms and the ball joints, and separate the lower
arms from the ball joints.
24. Remove both front subframe body mount brackets.
08/08/21 14:46:55 61SNR030_140_0238
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст